• Magazine of the Korea Concrete Institute
• /
• v.8 no.4
• /
• pp.171-179
• /
• 1996

A proposal of the basic fbrm on the design of joint parts that can increase the shear strength by the useful joint shapes of each member is intended. The vertical joint parameters are the number of' shear key and a variety of' reinfbrcement details and the horizontal joint paramctcrs arc t,hc number of shear key and the direction of' shear f'orcc. 10 PC panel vortical joint arid 12 PC panel horizontal joint specimens were tested to investigate the effects of these parameters. Test results show that : 1. The ductility of the test specimen that has the horizontal reinforcing steels is larger than that does not have. 2. The maximum resisting force of round bar specimen is similar to that of strand wire specimen under the condition of fixed horizontal displacement.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.4 s.74
• /
• pp.375-387
• /
• 2006

Different from the previous studies which investigated seismic P-$\Delta$ effect in slender columns though comparison of response spectra according to stability coefficients obtained from the analyses based on the assumed moment-curvature relationship, the axial force and P-$\Delta$ effect in RC columns are investigated on the basis of the layered section method which can effectively consider the changes of stiffness and yield strength due to the application of axial force in RC members. Practical ranges of slenderness and stability coefficient are assumed, and sixty sets of horizontal/vertical earthquake inputs are used in the analysis. From the parametric study, it is noted that the maximum deformation of the slender RC column is hardly affected by P-$\Delta$ effect or vortical earthquake but dominantly affected by the applied axial force. Therefore, it can be concluded that no additional consideration for the P-$\Delta$ effect and vortical earthquake is required in the seismic design of a slender RC column if the axial force effect is taken into account in the analysis and design procedures.

• 건축구조
• /
• v.12 no.4
• /
• pp.80-81
• /
• 2005

고층화의 최대 장점은 과밀한 수평 밀집 환경을 건축물의 수직적 확장으로 과밀 현상에서 다층 보행자 시스템으로 대지의 공지를 활용하는데 있다. 이러한 초고층 건물은 특성상 건물의 강도, 강성, 안전성 등을 고려하여 설계가 이루어졌고, 이러한 특성으로 인해 비교적 건물 내의 대공간 확보와 평면의 자유를 얻기 힘들었다. 그래서, 이런 단점을 보완하기 위해서 그 대안으로 SAC조와 현수교 구조(Cable)를 제안하고자 한다.

• Computational Structural Engineering
• /
• v.5 no.4
• /
• pp.41-45
• /
• 1992

본 실험에서는 가장 널리 쓰이는 base isolator의 한 종류로서 laminated rubber bearing을 제작하여 정적 및 동적 특성실험을 수행하였다. 앞에서 간략하게 언급한 실험결과에 대한 분석자료는 상부구조물과 기초와의 분리를 목적으로 본 실험에서 제작한 base isolator의 활용가능성을 검증하였다. 일반적으로 base isolator가 갖는 특성을 대부분 포함하고 있지만 본 실험결과에서 얻은 개선점은 i) 수직강성의 보강 ii) mounting plate와의 볼트연결부분 보완 iii) 최대전단변형을 증가시키기 위해 base isolator의 전체높이 조정 등으로 요약할 수 있다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.10a
• /
• pp.57-62
• /
• 2001

밀링은 회전공구를 사용하여 금속을 제거하는 효율적인 방법으로, 특히 수직밀링은 고능률절삭의 이점 때문에 널리 사용되는 금속절삭 가공방법중의 하나이다. 그러나 밀링커터는 단속절삭 공구로서 절삭 날의 단속절삭작용에 의한 변동절삭력과, 여러 날의 동시가공에 의한 절삭력의 교란 때문에 가공능률, 가공정밀도, 기계와 공구의 수명향상에 문제가 되어 왔다. 이러한 문제점들을 해결하기 위하여 기계설계자들은 절삭력의 교란에 의하여 일어나는 진동을 줄이기 위하여 기계구조의 강성을 증가시켰으나 이석은 고비용을 필요로 하게 되므로 공구 형상을 개선하여 안정된 절삭을 시도하였다.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.165-168
• /
• 2001

고 전계하에서 수직 및 수평 전계의 영향을 고려할 수 있는 Hewlett-Packard 이동도 모델을 구현하였다. HP 이동도 모델은 BANDIS에 구현되었다. 구현된 HP이동도 모델을 검증하기 위해 N-MOSFET과 P-MOSFET에 대해 모의실험을 수행하여 MEDICI와 비교한 결과, 드레인 전압-드레인 전류는 5% 이내의 최대 상대 오차를 보였고 전위 분포는 5% 이내의 최대 상대오차를 보였다. MEDICI에서는 1회 수렴을 하기위해 평균 4.6회 이하의 행렬 연산이 필요한 반면 BANDIS에서는 평균 4.3회 이하의 행렬 연산이 필요하다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.3
• /
• pp.282-288
• /
• 1982

크랙탄성평판의 굽힘문제가 경계적분방정식으로 구성되었다. 자연변수인 변위, 수직기울기, 굽힘 모우멘트, 등가전단적과 크랙끝에서 응력의 성장율로 정의되는 응력확대계수들이 주변수로 포함 된다. 이 적분방정식들은 가역에너지 적분이론(Green-Rayleigh)을 기초로 크랙응력분포특성에 맞 게 발전되었으며 해당되는 핵함수들이 유도되었다. 등분석 모우멘트를 받는 중앙크랙이 있는 정 4각형 모형에 대한 응력확대계수가 계산되어 기존의 유한요소법의 해와 비교되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.106-111
• /
• 2017

In this study, the stiffness of an LMU (Leg Mating Unit), which is a device required for installing the top side part of an offshore structure, was examined through structural analysis. This unit is mounted on the supporting point of the structure and is used to absorb the shock at installation. It is a cylindrical structure with an empty center. To support the vertical load, elastomeric bearings (EBs) and iron plates are laminated in layers. The stiffness of the EBs is basically influenced by the size of the bearings, but it varies with the number of laminated sheets inside the same sized structure. The relationship between the stiffener and the compressive stiffness is investigated, and its design is suggested. The stiffness of the EBs is analyzed by calculating the reaction force, while controlling the displacement. First, the relationship between the size of the reinforcing plate and the compressive stiffness is considered. Next, the relationship between the number of stacked reinforcing plates and the compression stiffness is considered. Different loads are required for each installed point. The goal is to design the compression stiffness in such a way that the same deformation occurs at each point in the analysis. In this study, ANSYS is used to perform the FE analysis.

• Journal of the Korean Society for Railway
• /
• v.18 no.2
• /
• pp.139-148
• /
• 2015

By increasing the vertical stiffness of the rail fastening system, the dynamic wheel load of the vehicle can be increased on the ballast track, though this increases the cost of track maintenance. On the other hand, the resistance acting on the wheel is decreased, which lowers the cost of the electric power to run the train. For this reason, the determination of the optimal fastener stiffness is important when attempting to minimize the economic costs associated with both track maintenance and energy to operate the train. In this study, a numerical method for evaluating the optimal vertical stiffness of the fasteners used on ballast track is presented on the basis of the process proposed by L$\acute{o}$pez-Pita et al. They used an approximation formula while calculating the dynamic wheel load. The evaluated fastener stiffness is mainly affected by the calculated dynamic wheel load. In this study, the dynamic wheel load is more precisely evaluated with an advanced vehicle-track interaction model. An appropriate range of the stiffness of the fastener applicable to the design of ballast track along domestic high-speed lines is proposed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.6
• /
• pp.533-540
• /
• 2012

Rubber laminated bearings with lead core are highly affected by changes in temperature because key materials which are rubber and lead have temperature dependencies. In this study, two full scale LRB(D800, S=5) are manufactured and temperature dependency tests on shear properties are accomplished. The shear properties at the 3rd cycle are used at $-10^{\circ}C$, $0^{\circ}C$, $10^{\circ}C$, $20^{\circ}C$, $30^{\circ}C$, $40^{\circ}C$ respectively. The double shear configuration, simultaneously testing two pieces, is applied for compression shear test in order to minimize the friction effects due to the test machine, described in ISO 22762-1:2010. Characteristic strength, post-yield stiffness, effective stiffness, equivalent damping ratio are estimated and presented coefficient due to the temperature changes.