• Journal of Radiation Protection and Research
• /
• v.21 no.2
• /
• pp.125-129
• /
• 1996

The energy response of HPGe detector for low energy Photons was determined by using three Monte Carlo codes. MCNP4A. EGS4, and CYLTRAN in ITS3. In this study. bare HPGe detector$(100 mm^2{\times}10mm)$ was used and a pencil beam was incident perpendicularly on the center of the detector surface. The photopeak efficiency, $K_{\alpha}$ and $K_{\beta}$ escape fractions were calculated as a function of incident X-ray energies ranging from 12 to 60 keV in 2-keV increments. Since the Compton. elastic. ana penetration fraction were negligible in this energy range. they were ignored in the calculation. Although MCNP. EGS, and CYLTRAN codes calculated slightly different energy response of HPGe detector for low energy Photons, it appears that the three Monte Carlo codes can Predict the low energy Photon scattering Processes accurately. The MCNP results, which are generally known as to be less accurate at low energy ranges than the EGS and ITS results. are comparable to the results of EGS and ITS and are applicable to the calculation of the low energy response data of a detector.

• Journal of radiological science and technology
• /
• v.37 no.1
• /
• pp.15-20
• /
• 2014

This study was to evaluate clinical feasibility of biodegradable polymeric membrane for interventional procedure in preliminary study. Bio-degradable polymetric membrane was produced into a solution by mixing hyaluronic acid powder with NaOH solution in a heating mantle. Three different concentrations of contrast media (10, 20, and 30 vol%) were added to the produced soluble powder, and vertical agitation was performed for 12 hours at a speed of 100 to 200 rpm at a room temperature. It was freeze dried for 24 hours at a temperature $80^{\circ}C$. Pressure on the freeze dried sample was exerted by a hydraulic press in order to form the freeze dried sample into a membrane. The membrane produced with varying contrast medium concentration was visually examined by a scanning electron microscope and radiographically inspected. Under the visual examination, the higher the concentration of contrast medium, the rougher the surface. Radiographic transparency was similar under all conditions of fluoroscopic radiography, simple radiography, and serial radiography. In conclusion, this preliminary study verified that bio-degradable membrane produced with hyaluronic acid was a material with clinical usability.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.6
• /
• pp.288-292
• /
• 2009

Hydrophobic/hydrophilic patterned substrates were fabricated on a glass substrate by a liquid phase deposition (LPD) method. Hydrophobic surface was obtained by modifying ZnO thin films with a rough surface using a fluoroalkyltrimethoxysilane (FAS) and hydrophilic surface was prepared by decomposing FAS on an exposed to UV light. The hexagonal ZnO rods were perpendicularly grown by LPD method on glass substrates with a ZnO seed layer. The diameter and thickness of hexagonal ZnO rods were increased as a function of increases of immersion time. The surface morphology, thickness, crystal structure, transmittance and contact angle of prepared ZnO thin films were measured by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), UV-visible spectrophotometer (UV-vis) and contact angle measurement. Hydrophilic ZnO thin films with a contact angle of $20^{\circ}{\sim}30^{\circ}$ were changed to a hydrophobic surface with a contact angle of $145^{\circ}{\sim}161^{\circ}$ by a FAS surface treatment. Prepared hydrophobic surface was pattered by an irradiation of UV light using shadow mask with $300\;{\mu}m$ or 3 mm dot size. Finally, the hydrophobic surface exposed to UV light was changed to a hydrophilic surface.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.21 no.1
• /
• pp.7-13
• /
• 1991

An anatomic radiolucency called medial sigmoid depression can be observed on a number of panoramic and mandibular oblique lateral views in the ramus just below and anterior to the mandibular sigmoid notch. The radiolucency may be unilateral or bilateral. Seventy-eight mandibles of dry skulls were visually examined and radiographed by panoramic machine. The observable incidence, the location center, and the mean size of the medial sigmoid depression were studied. Additionally, the radiographic incidence of the depression was determined using 500 panoramic radiographs. Normal anatomic radiolucent areas in the jaws are encountered often in the radiographs taken for the usual dental practice purpose. Some of these radiolucencies can be misdiagnosed as pathologic entities. But in most cases, the size, location, and appearance of the radiolucent area, and the presence or absence of symptoms can lead one to the correct diagnosis before surgery is undertaken. And this can be secured if diagnosticians are aware of the common and varied appearances of the normal anatomic radiolucencies A depression in the ramus just below and slightly anterior to the most inferior aspect of mandibular sigmoid notch shows occasionally foramen-like or notch-like radiolucency on some panoramic and oblique lateral views. This radiolucency was named medial sigmoid depression by Langlais et a1. in 1983. Since there're no reports about this medial sigmoid depression after that, (The author retrieved the Mediline from 1983 to 1990: Cambridge scientific abstracts, (7200 Wisconsin Ave Bethesda MD 20814 U.S.A.) National Library of Medicine) the author studied the size and the location of the depression of the mandible specimens, and determined the relationship between the observable anatomic incidence and its reproducibility on the radiographs.

• Journal of Broadcast Engineering
• /
• v.17 no.6
• /
• pp.964-975
• /
• 2012

Recently the attention on digital hologram that is regarded as to be the final goal of the 3-dimensional video technology has been increased. A digital hologram can be generated with a depth and a RGB image. We proposed a new system to capture RGB and depth images and to convert them to digital holograms. First a new cold mirror was designed and produced. It has the different transmittance ratio against various wave length and can provide the same view and focal point to the cameras. After correcting various distortions with the camera system, the different resolution between depth and RGB images was adjusted. The interested object was extracted by using the depth information. Finally a digital hologram was generated with the computer generated hologram (CGH) algorithm. All algorithms were implemented with C/C++/CUDA and integrated in LabView environment. A hologram was calculated in the general-purpose computing on graphics processing unit (GPGPU) for high-speed operation. We identified that the visual quality of the hologram produced by the proposed system is better than the previous one.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.1 s.38
• /
• pp.1-5
• /
• 2006

We prepared 80 nm-thick TiSix on each 70 nm-thick amorphous silicon and polysilicon substrate using an RF sputtering with $TiSi_2$ target. TiSix composite silicide layers were stabilized by rapid thermal annealing(RTA) of $800^{\circ}C$ for 20 seconds. Line width of $0.5{\mu}m$ patterns were embodied by photolithography and dry etching process, then each additional annealing process at $750^{\circ}C\;and\;850^{\circ}C$ for 3 hours was executed. We investigated the change of sheet resistance with a four-point probe, and cross sectional microstructure with a field emission scanning electron microscope(FE-SEM) and transmission electron microscope(TEM), respectively. We observe an abrupt change of resistivity and voids at the silicide surface due to interdiffusion of silicide and composite titanium silicide in the amorphous substrates with additional $850^{\circ}C$ annealing. Our result implies that the electrical resistance of composite titanium silicide may be tunned by employing appropriate substrates and annealing condition.

• Journal of the Korean Magnetics Society
• /
• v.12 no.4
• /
• pp.127-131
• /
• 2002

We fabricated MTJ devices that have doubly oxidized tunnel barrier using plasma oxidation method to from oxidized AlO$\sub$x/ tunnel barrier. Doubly oxidation I, which sputtered 10 ${\AA}$-bottom Al layer and oxidized it with oxidation time of 10 s. Subsequent sputtering of 13 ${\AA}$-Al was performed and the metallic layer was oxidized for 50, 80 and 120 s., respectively. Doubly oxidation II, which sputtered 10 ${\AA}$-bottom Al layer and oxidized it varying oxidation time for 30∼120 s. Subsequent sputtering of 13 ${\AA}$-Al was performed and the metallic layer was oxidized for 210 sec. Double oxidation process specimen showed MR ratio of above 27％ in all experiment range. Singly oxidation process. 13 ${\AA}$-Al layer and oxidized up to 210 s, showed less MR ratio and more narrow process window than those of doubly oxidation. Cross-sectional TEM images would that doubly oxidized barrowers were thinner and denser than singly oxidized ones. XPS characterization confirmed that doubly oxidation of Fe with bottom insulating layer. As a result, doubly oxidation could have superior MR ratio in process extent during long oxidation time because of preventing oxidation of bottom magnetic layer than singly oxidation.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.2
• /
• pp.88-99
• /
• 1997

뉴질랜드산(産) 라디아타소나무의 수간(樹幹) 및 지재(枝材)에 발달(發達)되어 있는 압축이상재(壓縮異常材), 대응재(對應材) 및 측면재(側面材)의 해부학적(解剖學的) 특성(特性)을 광학현미경(光學顯微鏡), 주사전자현미경(走射電子顯微鏡) 그리고 투과전자현미경(透過電子顯微鏡)을 이용하여 조직학적(組織學的) 및 구성요소(構成要素)의 수량적(數量的) 측면(側面)에서 비교(比較), 검토(檢討) 하였다. 조직학적(組織學的)인 면(面)에서 볼 때 춘재(春材)로부터 추재(秋材)로의 가도관(假導管) 이행(移行)은 대응재(對應材)나 측면재(側面材)보다 압축이상재(壓縮異常材)가 훨씬 더 점진적(漸進的)이었다. 편심생장(偏心生長)으로 인해 연륜폭(年輪幅)은 압축이상재(壓縮異常材)가 가장 컸고 그 다음이 측면재(側面材) 및 대응재(對應材)의 순이었으며 추재솔(秋材率) 역시 압축이상재(壓縮異常材)가 대응재(對應材) 및 측면재(側面材)보다 컸다. 횡단면상(橫斷面上) 가도관(假導管) 형상면(形狀面)에서 압축이상재(壓縮異常材)가 원형(圓形)을 나타내는 반면 대응재(對應材)와 측면재(側面材)는 각형(角形)을 띠고 있었다. 또한 압축이상재(壓縮異常材)에서만 가도관(假導管)의 세포벽(細胞壁)에 나선강(螺旋腔)과 나선열(螺旋裂) (helical cavity and check), 슬릿(slit)형(形) 벽공구(壁孔口)가 존재(存在)하였으나 $S_3$층(層)이 결여(缺如)되어 있었으며 굴곡(屈曲)된 선단(先端)과 불규칙(不規則)한 형상(形狀)의 가도관(假導管) 및 세포간극(細胞間隙)이 자주 관찰(觀察)되었다. 직교분야(直交分野) 벽공(壁孔)은 압축이상재(壓縮異常材)가 가문비나무형(型) 그리고 대응재(對應材) 및 측면재(側面材)는 소나무형(型) 벽공(壁孔)을 나타냈다. 수량적(數量的) 특성(特性) 면에서 볼 때 가도관(假導管)의 길이는 압축이상재(壓縮異常材)가 가장 짧고 측면재(側面材)가 가장 길었으며 가도관(假導管)의 벽(壁) 두께는 압축이상재(壓縮異常材)가 대응재(對應材)나 측면재(側面材)보다 두꺼웠다. 수직수지구(垂直樹脂溝)는 대응재(對應材)가 그리고 수평수지구(水平樹脂溝)(방추형(紡錐形) 방사조직(放射祖織))는 압축이상재(壓縮異常材)의 쪽이 많았다. 결론적(結論的)으로 보면 라디아타소나무의 압축이상재(壓縮異常材)는 근본적으로 대응재(對應材)나 측면재(側面材)와는 상이(相異)한 특성(特性)을 지녔으나 대응재(對應材)와 측면재(側面材)는 거의 유사(類似)한 특성(特性)을 공유(共有)하는 것으로 밝혀졌다.

• Journal of the Korean Vacuum Society
• /
• v.17 no.1
• /
• pp.51-57
• /
• 2008

we have demonstrated structural evolution and optical properties of Si-nanowires (NWs) synthesized on Si (111) substrates with nanoscale Au-Si islands by rapid thermal chemical vapor deposition (RTCVD). The Au-Si nano-islands (10-50nm in diameter) were employed as a liquid-droplet catalysis to grow Si-NWs via vapor-liquid-solid mechanism. The Si-NWs were grown by a mixture gas of SiH4 and H2 at a pressure of 1.0 Torr and temperatures of $500{\sim}600^{\circ}C$. Scanning electron microscopy measurements showed that the Si-NWs are uniformly sized and vertically well-aligned along <111> direction on Si (111) surfaces. The resulting NWs are ${\sim}60nm$ in average diameter and ${\sim}5um$ in average length. High resolution transmission microscopy measurements indicated that the NWs are single crystals covered with amorphous SiOx layers of ${\sim}3nm$ thickness. In addition, the optical properties of the NWs were investigated by micro-Raman spectroscopy. The downshift and asymmetric broadening of the Si main optical phonon peak were observed in Raman spectra of Si-NWs, which indicates a minute stress effects on Raman spectra due to a slight lattice distortion led by lattice expansion of Si-NW structures.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.1
• /
• pp.39-44
• /
• 2012

The new blind design of sunlighting has been suggested in this study. The material in this blind becomes transparent but the blind has the parabolic edge section having the perpendicular line on a side. The material of this blind is PolyMethly MethAcrylate(PMMA). In this parabolic edge section, the front side of the blind is designed perpendicular to the ground. But the back side is a little tilted to the front side. The rays of reflected sun at the front side can be easily reflected totally by the back side. If the inclination angle in this parabolic edge section at the back side is designed with $15^{\circ}$, it can transmit the rays of sun when the height of the sun is lower than $45^{\circ}$. But it can reflect the rays of sun when the height of the sun is upper than $45^{\circ}$. The suggested design of blind can be applied to the existing blind installation. Although the material in this blind becomes transparent, the rays of sun can be reflected totally at midday. There is also prospect outside of the blind because the material becomes transparent. Several inclination angles in the suggested design have been simulated for the various height of sun. Total reflections have been occurred by the suggested blind design at midday and it can be useful to shut out the sunlight.