Kim, Jae-Won;Kim, Hyeon-Cheol;Kim, Du-Hyeon;Seo, Seong-Mun;Jo, Chang-Yong;Choe, Seung-Ju;Kim, Jae-Cheol
Korean Journal of Materials Research
/
v.10
no.3
/
pp.233-240
/
2000
In order to fabricate dense cordierite ceramics without sintering aid, thermal behavior of Mg-Al-Si compounds during sintering was investigated. The dispersibility of cordierite suspension in aqueous media was measured by ESA(electrokinetic sonic amplitude). To prevent aggregation and insufficient dispersion of the cordierite sol, the pH of the suspension was controlled to 1.03 and 8.30 by adding $2N\;HNO_3$ and $2N\;NH_4OH$, respectively. Magnesium-aluminum-silicate complex gel coexisted in the specimen which has been gelled at $150^{\circ}C$ fir 12 hours, however several metastable phase such as ${\mu}-cordierite(Mg_2Al_4Si_5O_{18}),\;spine(MgAl_2O_4)\;and\;mullite(Al_6Si_2O_{13})$ existed below $1300^{\circ}C$ Nucleation rates of the two suspension were similar, but densification of the gel was sensitive to the pH of the sol. Densification of the sol with the pH of 8.3 was more pronounced than that of the sol with pH of 1.63.
The surface treated hydroxypropyl methylcellulose(HPMC) which could adjust the soluble time was synthesized when 40 wt % glyoxal solution and $KH_2PO_4$ were sprayed and reacted. And also, the solution dynamic at different ratios of two adding agents were identified If the surface of HPMC was treated with only glyoxal, the dispersion characteristics at different ratios of two adding agents were identified If the surface of HPMC was treated with only glyoxal, the dispersion was observed in the neutral solution and the viscosity was increased after directly dissolved as the solution become alkali condition. But the fine-powder type of HPMC which reacted with glyoxal and $KH_2PO_4$ was dispersed regardless of pH of solution and observed that it was dissolved and its viscosity increased after elapsing some time. With increasing amount of glyoxal and $KH_2PO_4$, the soluble time was delayed. The reaction condition was about 60 min at $75{\sim}85^{\circ}C$. Especially, the removal process of organic solvent after reaction was not required due to reaction under water solution without organic during glyoxal and $KH_2PO_4$ treatment. And also, the HPMC which could adjust the soluble rate in water or organic solvent by changing the degree of substitution of HPMC was synthesized.
Jo, Jin-Oh;Choi, Kyeong Yun;Gim, Suji;Mok, Young Sun
Applied Chemistry for Engineering
/
v.26
no.3
/
pp.311-318
/
2015
This work investigated the plasma treatment of aqueous bisphenol A (BPA) solution and mineralization pathways. For the effective contact between plasmatic gas and aqueous BPA solution, the plasma was created inside a porous ceramic tube, which was uniformly dispersed into the aqueous solution through micro-pores of the ceramic tube. Effects of the gas flow rate, applied voltage and treatment time on the decomposition of BPA were examined, and analyses using ultraviolet (UV) spectroscopy, ion chromatography and gas chromatography-mass spectrometry were also performed to elucidate mineralization mechanisms. The appropriate gas flow rate was around $1.0L\;min^{-1}$; when the gas flow rate was too high or too low, the BPA decomposition performance at a given electric power decreased. The increase in the voltage improves the BPA decomposition due to the increased electric power, but the energy required to remove BPA was similar, regardless of the voltage. Under the condition of $1.0L\;min^{-1}$ and 20.8 kV, BPA at an initial concentration of $10L\;min^{-1}$ (volume : 1 L) was successfully treated within 30 min. The intermediates produced by the attack of ozone and hydroxyl radicals on BPA were further oxidized to stable compounds such as acetate, formate and oxalate.
Reductive reactivity of zero-valent iron nanoparticles was investigated for removal of nitrate-nitrogen which is considered one of the major water pollutants. To elucidate the difference in reactivity between preparation methods, iron nanoparticles were synthesized respectively from microemulsion and aqueous solution of ferric ions. Iron nanoparticles prepared from microemulsion were deposited on aluminum by electrophoretic method, and their reaction kinetics was compared to that of the same nanoparticles suspended in aqueous batch reaction. With an approximation of pseudo-first-order reaction, rate constants for suspended nanoparticles prepared from microemulsion and dilute aqueous solution were $3.49{\times}10^{-2}min^{-1}$ and $1.40{\times}10^{-2}min^{-1}$, respectively. Iron nanoparticles supported on aluminum showed ca. 30% less reaction rate in comparison with the identical nanoparticles in suspended state. However, supported nanoparticles showed the superior effectiveness in terms of nitrate-nitrogen removal per zero-valent iron input especially when excess amounts of nitrates were present. Iron nanoparticles deposited on aluminum maintained reductive reactivity for more than 3 hours, and produced nitrogen gas as a final reduction product of nitrate-nitrogen.
We synthesized PEG-PLA (or PLGA) amphiphilic di-block copolymers, which consist of PEG as biocompatible and hydrophilic block and PLA (or PLGA) as biodegradable and hydrophobic block, by ring opening polymerization of LA in the presence of methoxy PEG as a macroinitiator. The compositions and the molecular weights of the copolymers were controlled by changing the feed ratio of LA (and GA) to PEG initiator. The di-block copolymers could self-assemble in aqueous media to form micellar structure. A hydrophobic model drug, pioglitazone, was loaded into the polymer micelle using solid dispersion and dialysis methods, and the drug-loaded micelles were characterized by AFM, DLS and HPLC measurements. The drug loading capacity and in vitro release studies were performed and evaluated under various conditions. These results indicated that the amphiphilic di-block copolymers of PEG-PLA (or PLGA) could solubilize pioglitazone by solid dispersion method and the drug release was modulated according to micellar chemical compositions.
Silver nanoparticles were prepared by chemical reduction-protection method using 1-decanoic acid and tri-n-octylphosphine as surfactants, and using $NaBH_4$ as a reducing agent. The silver nanoparticles were also studied for their formation, structure, morphology and size using UV-Visible spectroscopy, XRD, TEM and SEM. Further the viscosity of the silver paste and the surface resistance of the silver metal film produced by screen coating onto a PET film were investigated. Well dispersed and quasispherical silver nanoparticles with the size of 10-200 nm were obtained under the optimal molar ratio of $NaBH_4/AgNO_3=1:5$. The surface resistance of silver metal film coated on the PET film made with the silver nanoparticles under the optimal molar ratio showed a minal value of $41{\mu}{\Omega}/cm^2$.
Platinum nanoparticles loading on carbon nanotube was carried out by impregnation of hexachloro platinate(IV) from hydrogen hexachloro platinate(IV) hydrate dissolved solution without using reduction agents, and heating the hexachloro platinate(IV) impregnated carbon nanotube up to $400^{\circ}C$. The amounts of impregnated hexachloro platinate(IV) on to carbon nanotube were measured with UV-visible spectrophotometer. The TG, XRD, and TEM analysis were performed to confirm the platinum particles loading and distribution on carbon nanotube. The average platinum particles size on carbon nanotube was under 2 nm by heating the hexachloro platinate(IV) up to $400^{\circ}C$ in spite of non-using reduction agents, while the average size increased due to the agglomeration of some particles by heating them up to $800^{\circ}C$. Therefore, uniformly distributed platinum nanoparticles loading on carbon nanotube can be obtained from simple impregnation of hexachloro platinate(IV) from solution and heating it up to $400^{\circ}C$.
Monodisperse, spherical $SiO_2/TiO_2$ composite fine powders were prepared by modified Sol-Gel process which $TiO_2$ fine Powders was used as a seed particles for condensation of TEOS (Tetraethyl Orthosilicate). The reaction was carried out under $N_2$ atmosphere at ambient temperature using $NH_3$ as a catalyst. Ethanol was used as a solvent. Drying process was carried out with vacuum trap which cooled by liquid $N_2$. The reaction variables were the concentration of TEOS, the concentration of ammonia, the size of $TiO_2$ seed and molar ratio of $SiO_2/TiO_2$. The optimum condition for the preparation of $SiO_2/TiO_2$ composite fine powders without agglomeration was [TEOS]=0.3M, [$NH_3$]=0.7M, size of $SiO_2/TiO_2$ seed = 200~300nm.
Direct contact heat exchange (DCHE) method has been employed to investigate the separation of ethanol from dilute aqueous solutions. Bubbles at high temperature were dispersed into a continuous liquid phase, generating temperature gradient in air-liquid interface, which causes heat and mass transfer accordingly. The experiments were performed in the ranges of jet regime air flow. The air-water stripping coefficient increased $5{\sim}10,\;and\;1{\sim}1.5$ times as temperature and air flow rate increased, respectively. The recovery ratio based on the initial ethanol concentration reached into 80% at the air flow rate of 84.88 m/min. The initial ethanol concentration showed little effect on the stripping coefficient and the recovery ratio.
Proceedings of the Materials Research Society of Korea Conference
/
2012.05a
/
pp.104.2-104.2
/
2012
이종 재료의 접합에 대한 연구는 단일 재료에서 얻을 수 없는 물리적/기계적 특성과 이종 재료의 우수한 특성을 얻을 수 있다는 장점이 있어 국내외 적으로 연구가 활발히 진행되고 있다. 이러한 이종 접합 기술은 구조재료와 에너지 변환분야에 가장 많이 사용되고 있으며, 그 외 광촉매와 Thin film, 경량구조재료 등에도 사용되고 있다. 그 중 FGM(Functional Graded Materials)는 조성의 점진적인 변화를 통하여 접합하는 방법으로 이종 재료 접합 시 발생하는 내부 응력을 해소해줌으로써 적합한 방법이라고 할 수 있다. FGM 제작에 사용되는 방법으로 널리 알려진 것들로는 plasma spraying, 원심주조, 분말 야금법, PVD, CVD 그리고 EPD(electrophoretic deposition) 등이 있다. 이중에서 EPD는 수용액이나 유기용매와 같은 분산매체 중에 콜로이드 입자의 표면에 대전되는 전하를 이용하여, 외부에서 전장을 걸어서 입자의 움직임을 제어하는 기술이다 EPD는 코팅 속도가 상대적으로 빠르고 두꺼운 코팅 층 제작이 가능하다. 또한 바인더, 윤활제 또는 가소제를 사용하지 않고 다양한 종류와 모양의 기판 위에 균일한 코팅이 가능하다는 장점이 있다. 본 연구에서는 Ni substrate를 이용하여 그 위에 Ni과 $Al_2O_3$의 조성을 점진적으로 변화시켜 FGM을 EPD 방법으로 코팅하였다. 여기서 사용된 Ni은 높은 녹는점과 좋은 연성으로 인해 성형이 용이하여 구조재료로 적합하며, $Al_2O_3$는 고내열성과 내부식성을 가지며 경도가 높다는 장점이 있다. 본 연구에서는 EPD 방식을 이용하여 Ni/$Al_2O_3$ FGM을 코팅하였으며, 코팅 후 발생하는 substrate와의 접착력 문제를 해결하기 위해서 건조 방식과 substrate의 표면 상태를 최적화하여 다층의 Ni/$Al_2O_3$ FGM을 코팅 및 소결하였다. Zeta-potential 측정을 통해 electrophoretic mobility와 suspension의 분산 안정도를 평가 할 수 있었으며, X-ray 회절 분석(XRD)을 통하여 Ni 의 환원 여부를 확인하였다. 또한 Scanning electron microscopy(SEM) 분석을 통하여 미세구조 분석을 하였고, 최종적으로 Electron Probe Micro Analyzer (EPMA) 를 이용하여 다층 구조의 조성변화를 확인함으로 Ni/$Al_2O_3$의 FGM 코팅이 이루어졌음을 확인하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.