• Proceedings of the KAIS Fall Conference
• /
• 2007.05a
• /
• pp.66-68
• /
• 2007

본 논문에서는 CDMA 상향 중심주파수인 836.5MHz에서 단말기 송신 전력 제어를 위한 Schottky 다이오드 전력 검출기 기본 회로 구조를 제안한다 일반적인 다이오드의 비선형성에 의한 검파 출력의 선형성 개선과 낮은 입력 레벨의 출력 전압 감도 특성을 개선하기 위해서 낮은 검출기 입력 레벨에서의 임피던스 매칭을 한다 다이오드 패키지의 기생 성분을 고려한 시뮬레이션을 통하여 비교적 정확한 측정 결과를 예측할 수 있다. 본 논문의 전력 검출기의 전압 감도는 최대 0.1V의 비교적 우수한 특성을 보이며, -20dBm에서 +15dBm의 검출기 입력 대역에서 임피던스 매칭의 분석을 통하여 선형성의 뚜렷한 개선 효과를 얻는다. 또한 입력 주파수의 대역폭에 따른 매칭특성과 개선된 검파 출력 특성도 제시된다.

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.1905-1906
• /
• 2006

VSAT(Very Small Aperture Terminal)는 일반 가정이나 기업에서 인공위성을 이용해 양방향 통신이 가능하도록 하는 초소형 위성통신장비로 통신 인프라가 갖춰지지 못한 산간 오지지역의 정보를 실시간으로 처리해야 하는 곳을 중심으로 최근 수요가 늘고 있다. 위성 통신용으로 Ku Band 대역의 주파수를 사용하여 데이터를 전송하는 경우에는 전파가 대기권을 통과할 때 강우에 의한 감쇠를 많이 받게 되며, 회선 품질에 매우 심각한 영향을 주게 된다. 이러한 신호감쇠에 대한 보상방법으로 비콘신호의 세기를 분석하여 전력을 제어하는 방법이 제시되고 있다. 본 연구에서는 VSAT 단말지구국의 송신전력에 비례하여 출력을 제어함으로써 데이터 전송환경의 변화에 따른 전파의 세기가 감쇠되는 것을 보상하도록 VSAT의 Outlink 수신레벨을 감시하여 정해진 방법에 의해 VSAT의 Tx Attenuation을 조정하여 안정적인 위성링크 상태를 보장하도록 하는 기능과 호출 및 Event 발생시간을 저장함으로 데이터의 검보정에 활용할 수 있는 기능을 갖는 VSAT 송신전력 제어기를 개발하였으며, 단말지구국에 설치하여 운영된 데이터를 분석하고자 한다.

• Proceedings of the KIPE Conference
• /
• 2014.11a
• /
• pp.3-4
• /
• 2014

무선전력전송 회로는 부하의 변동에 따라 출력값을 알맞게 제어해 줄 필요가 있는데 송신부와 수신부 회로는 분리되어 있으므로 제어루프 또한 분리되어야 한다. 기존에는 주로 통신방식이나 부하측 변조를 이용한 1차측 제어를 사용하였다. 하지만 통신을 이용하는 경우 가격이 비싸고 시스템이 복잡하며, 부하측 변조 방식은 제어회로의 반응이 느리다는 단점이 있다. 본 논문은 2.5W급 전계결합형 무선전력회로에 대하여 LED 광학링크를 이용해 송신부의 스위칭 주파수를 제어하는 회로를 제안한다. 이 회로는 수신부에 포토다이오드와 연산증폭기를 내장하여 부하에 추가적인 배터리전원 없이 저가로 우수한 성능의 제어기를 구성할 수 있으며, 그 성능을 하드웨어로 검증하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.2
• /
• pp.339-346
• /
• 2011

In the existing RF communication based WPAN environment, a lowering of battery span and interference problem among sensors occur because the value of output is set and transmitted steadily when the system on sensor is initialized. Therefore, this paper proposes a framework and a transmit method with low power which decreases the electricity consumption by properly controling transmit power of opponent by received signal strength indicator(RSSI) of each sensor. The system proposes a power-lowering method by controling transmit power properly by the transmit intensity of the connected sensor after being affected by the transmit intensity of surrounded sensor. The framework that is proposed in this paper includes data transmit module, transmit power manager module, transmit power searching module, signal transmit module, and signal receiving module.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.5
• /
• pp.1311-1319
• /
• 1998

The methods of providing available bandwidth adaptively using feedback to maximize the utilization of network as well as the quality of service have been the focus of recent research activities for ATM(Asynchronous Transfer Mode). This study has been extended from the point-to-point connection to a point-to-multipoint environment as the number of applications requiring multicast service increases. It is known that the effectiveness of feedback based congestion control scheme diminishes as propagation delay increases. Especially for a multicast connection consisting of various paths and destinations with different performance and congestion status, the problem of unfairness due to different propagation delays may occur. The degree of such unfairness may change depending on various aspects of congestion control schemes. These has been, however, relatively little study on these problems. In this paper, we present how various aspects of control schemes-length of the interval between feedback generations, point of time to coalesce feedback cells from child paths, decreasing factor of source rate in case of congestion-affect the degree of unfairness. Simulation results show that degree of unfairness changes according to when the feedback coalescing happens. Expecially it is shown that the effect of feedback coalescing time to the degree of unfairness is more significant for the smaller feedback interval. It is also found that as the source rate decreasing factor becomes larger the average ACR(Allowed Cell Rate) at the source gets lower and the degree of unfairness grow larger.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.9
• /
• pp.1077-1082
• /
• 2007

This paper presents the analysis of the potential ultra-wideband(UWB) interference to WiMAX at 3.5 GHz bands and the mitigation method using transmit power control(TPC) of UWB system. UWB interference effect is evaluated with WiMax's outage probability over UWB density when multiple UWB systems and single WiMAX receiver distribute in unit area of 1$km^2$, When UWB distribution density is 20$devices/km^2$ and the dynamic range of TPC is 30 dB, UWB interference effect with TPC is decreased by 42 % rather than that without mitigation scheme. Finally, we describe that the proposed TPC is an effective method to mitigate UWB interference to WiMAX.

• Journal of Digital Contents Society
• /
• v.18 no.2
• /
• pp.365-371
• /
• 2017

IEEE 802.11 Wireless Local Area Network (WLAN) adopts Power Saving Mode(PSM) to save the power. Unlike existing PSM, this paper proposes a new scheme for the power saving of the Mobile Host(MH) when a MH performs the data transmission after the competition-based DCF(Distributed Coordination Function) and competition free-based PCF(Point Coordination Function). In this paper, The proposed scheme estimates the distance between the MH with the authority of data transmission and the Access Point(AP) and then adaptively controls the power of the MH considering the distance. Through the simulation result, we find that the proposed scheme consumes the smaller transmission power and has the similar success rate of packet transmission when it is compared to the existing scheme which uses the same power without the consideration of the distance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.25-30
• /
• 2007

In this paper, we proposed a new burst-mode optical transmitter structure which is suitable for high data rate operation such as Gb/s operation. With this structure we made a 1.25Gb/s burst-mode optical transmitter including a digitally controlled APC circuit for EPON systems using commercial 0.8m BiCMOS technology. It well functioned at 1.25Gb/s and showed good eye patterns with 53.3ps jitter, 191ps rise time and 258ps fall time. To characterize the APC function we measured optical output power as increasing external voltage VREF. The optical power is linearlyproportional to VREF at the rate of 0.293mW/V.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.159-162
• /
• 2015

In this paper, implement a baby monitor using the arduino for deaf and Visually Impaired. The proposed baby monitors are divided into measuring part & transmit part and linked with the application. The measuring part consists of a sound volume sensor, a transmit part consists of a bluetooth module. The measuring part and transmit part are controlled by the Arduino board. Measure the value of the sound by the sound sensor and delivers value to the arduino board. The measured value is sent to the application by the bluetooth module of transmit part. The application determines the received value and control the smart phone, and outputs the light from the sound and vibration for the value. It showed that the proposed baby monitor and an application is correctly operating in accordance with the value.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.6
• /
• pp.518-521
• /
• 2019

In this paper, an active antenna module operating in the 60 GHz band is designed and fabricated by combining a commercial transmitter chip and patch array antenna. The designed module is composed of an antenna PCB and a PCB with a transmitter chip. The frequency-control and bias-control signals are applied to the transmitter chip, using an Arduino kit. A baseband I/Q signal is also applied to the chip. A ring hybrid balun converts the output of the transmitter module to a single output, which is the output of the transmitter chip that outputs a differential output. The output is delivered to the $2{\times}4$ microstrip patch array antenna PCB as a micro-computer connector. The radiation pattern of the millimeter-wave signal of the final output is compared with the simulation results. The measured radiation patterns of the fabricated active antenna module confirm that the positions of the 3 dB beam width and null point agree well with the simulation results.