• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.9C
• /
• pp.871-878
• /
• 2002

The cartesian loop chip which is one of key devices in narrow-band Walky-Talky transmitter using RZ-SSB modulation method was designed and implemented with 0.35 ㎛ CMOS technology. The reduced size and low cost of transmitter were available by the use of direct-conversion and cartesian loop chip, which improved the power efficiency and linearity of transmitter. In addition, low power operation was possible through CMOS technology. The performance test results of transmitter showed -23㏈c improvement of IMD and -30㏈c below suppression of SSB characteristic in the operation of cartesian loop chip (closed-loop). At that time, the transmitting power was about 37㏈m (5W). The main parameters to improve the transmitting characteristic and to compensate the distortion in feed back loop such as DC-offset, loop gain and phase value are interfaced with notebook PC to be controlled with S/W.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.7
• /
• pp.1326-1331
• /
• 2001

This paper has been studied about design of a transceiver for data transmission. The transceiver has bandwidth of 424.7~424.95 MHz and uses half duplex communication method, PLL synthesized, 20 channel, 12.5 KHz channel bandwidth and FSK modulation/demodulation method. The transmission set is designed using low noise amplifier and power amplifier Also, it consists of low pass filter and resonation circuit for decrease of spurious signal. The receiver set is designed using dual conversion method. Finally, the transceiver set achieves the following characteristics 9.71dbm output power, 47dbc spurious property and $\pm$12.3 Jitter at sensitivity of -1134dbm.

• Journal of Korea Multimedia Society
• /
• v.15 no.7
• /
• pp.903-909
• /
• 2012

In this paper, we analyze the sharing performances for coexistence of different communication systems between adjacent channels in TV White space. We analyze the parameter performance result according to various density of interfering transmitter and transmitter output. Two cases are analyzed to consider an interference effect between each system. First, WiBro is an interfering transmitter and WLAN is a victim receiver. Second, WLAN is an interfering transmitter and WiBro is a victim receiver. Free space channel model, Extended Hata and IEEE 802.11 model are used for channel environment. Analyzed coexistence results under various co-use scenarios may be widely applied into the technique developed to get the coexisting condition for wireless devices using many communication protocols in adjacent frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.4
• /
• pp.286-289
• /
• 2019

In this paper, we proposed a method to control input powers and receiver loads for maximum efficiency in multiple-input multiple-output(MIMO) wireless power transfer(WPT) systems. The input voltage ratio between transmitters and receiver loads for maximum transfer efficiency is derived in terms of figure of merits. The theoretically derived input voltages for the transmitters and optimum loads for the receivers were found to be similar to those obtained by a genetic algorithm. We demonstrate the effectiveness of the theory using a few design examples. Using the results obtained from this study, effective and simplified designs of MIMO WPT systems will be possible.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2018.06a
• /
• pp.28-30
• /
• 2018

본 논문에서는 전이중 통신 방식을 사용하는 DOCSIS 3.1 시스템의 자기간섭 제거를 위한 자기간섭신호의 채널 및 비선형 왜곡 요소를 추정하는 기술을 제안한다. DOCSIS 3.1 시스템의 전이중 통신 방식은 일반적으로 가입자 단말인 CM (Cable Modem) 과 케이블방송신호 송신 시스템인 CMTS (Cable Modem Termination System) 사이의 상하향 통신을 시간/주파수의 분할 없이 동시에 수행하는 통신 방식이다. CMTS 에서 CM 의 신호를 수신함과 동시에 CMTS 신호를 송신하는 경우 고출력의 CMTS 송출신호가 CMTS 의 수신기로 인가되는 자기간섭 현상이 발생하게 된다. 이렇게 인가되는 자기간섭신호는 고출력 증폭기 (HPA: High - Power Amplifier) 및 Feedback 채널의 영향으로 크게 왜곡되어 수신된다. 따라서 자기간섭신호를 제거하고 CM 의 신호를 원활하게 복조하기 위해서는 자기간섭신호의 왜곡 요소룰 추정 및 보상하는 절차가 반드시 필요하다. 본 논문에서는 자기간섭신호의 HPA 에서 발생하는 비선형 왜곡 요소 및 Feedback 채널의 영향으로 발생하는 채널 요소를 추정하는 기술을 제안하고 성능을 분석한다. 제안된 기술은 간단한 연산기반으로 왜곡요소의 추정이 가능하며 반복추정을 통해 성능을 효과적으로 향상시키는 것이 가능하다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.6
• /
• pp.245-250
• /
• 2015

We have developed an optical video transmission device for HD-SDI signal transmission. The optical transmitter/receiver unit operates at DC 5 volt and small enough to be attaced near surveillance camera. They have internal voltage regulating circuits to supply 3.3V to other circuits inside the unit. The optical transmitter is composed of cable driver, laser diode driver, and laser diode. The optical receiver is composed of photodiode, limiting amp, and cable equalizer. The wavelength of the trasmitter was 1.3 um, and optical power was -5dBm, and the speed was 1.485Gbps. The receiver sensitivity was -23 dBm. We confirmed that the optical device can transmit HD-SDI video through 30 km optical fiber without any interruption.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.111-121
• /
• 2014

A bi-directional DC-DC converter has been developed for a wireless power transceiver which enables a device to receive and transmit power wireless. Generally, the wireless power transceiver requires two DC-DC covnerter and two external inductors. However, the proposed wireless power transceiver requires only one DC-DC converter and one inductor, allowing small form-factor. The bi-directional DC-DC converter implemented in $0.35{\mu}m$ BCDMOS process operates as a buck converter at the wireless power receiving mode and the power efficiency is 91% when the ouput power is 3W. In the wireless power transmitter mode, the DC-DC converter operates as a boost converter. With the bi-directional DC-DC converter and the proposed efficiency maximizing techniques, the power efficiency of wireless power transceiver is 81.7% in receiver mode and 76.5% in transmitter mode.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.8
• /
• pp.1-11
• /
• 2012

The multi-code spread spectrum communication system, which spreads data bit stream by multiplexing orthogonal codes, can transmit data in high rate. However it needs the high-cost good linear amplifier because of the multi-level output signal. In order to overcome this drawback several systems making the amplitude of output signal constant with Walsh codes have been proposed. Recently constant amplitude pre-coded multi-code spread spectrum systems using extended m-sequence have been proposed. In this paper we consider an extended m-sequence based constant amplitude multi-code spread spectrum system with code set partitioning. By grouping the orthogonal codes into 4 subsets, not only is the computational complexity of the transceiver reduced but BER performance also improves. It has been shown that parity checking on four detected codes at the receiver can correct code detection error and result in BER performance enhancement. In this paper we propose a improved parity check receiver. We carried out computer simulation to verify feasibility of the proposed algorithm.

• Journal of Advanced Navigation Technology
• /
• v.18 no.1
• /
• pp.35-43
• /
• 2014

In this paper, it is about to non-contact wireless power transmission according to various conditions of self induction principle between the two planar coils at a transmission unit and a receiving unit based on the theory of wireless power transmission. The experiments are occurred in order to power transfer of noncontact method from designed wireless circuits in the primely coil and secondary coil, and the applying to Half Bridge Resonant converter transmission unit and receiving unit. and that were able to prepared circumstance to calculate of the output voltage and power source. The main power of the inductive coupling the resonant converter at the transmission unit is converted electrical energy using the solar cell module and artificial light source (halogen lamp) as a replace light and received 24 V power supply from solar power was used a input power source for the wireless power transmission device. Experimental results, to received of power is used to illuminate the lighting and to charge the battery in receiving circuit.And the wireless power transmission efficiency measured at the output side of the transmission unit is obtained about 70% to 89% compared to input power of receiving unit.In addition, efficiency were tested through ID verification method and comparing the phase difference between the voltage when foreign substances interfere with wireless power transmission.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.6
• /
• pp.467-478
• /
• 2019

This paper describes the development and measurement results of a wide-band planar active phase array antenna system for an electronic warfare jamming transmitter. The system is designed as an $8{\times}8$ triangular lattice array using a $45^{\circ}$ slant wide-band antenna. The 64-element transmission channel is composed of a wide-band gallium nitride(GaN) solid state power amplifier and a gallium arsenide(GaAs) multi-function core chip(MFC). Each GaAs MFC includes a true-time delay circuit to avoid a wide-band beam squint, a digital attenuator, and a GaAs drive amplifier to electronically steer the transmitted beam over a ${\pm}45^{\circ}$ azimuth angle and ${\pm}25^{\circ}$ elevation angle scan. Measurement of the transmitted beam pattern is conducted using a near-field measurement facility. The EIRP of the designed system, which is 9.8 dB more than the target EIRP performance(P), and the ${\pm}45^{\circ}$ azimuth and ${\pm}25^{\circ}$ elevation beam steering fulfill the desired specifications.