• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.9 s.339
• /
• pp.65-70
• /
• 2005

For the base station or repeater which is in operation as part of a mobile communication system, any kind of degradation in antenna performance such as lowered gam or increased VSWR which maybe due to aging of antenna, connector corrosion or other environmental factors, is difficult to detect and react to immediately. In this paper, a VSWR measurement device which is capable of detecting the VSWR of a PCS forward path ($1,840\~1,870$MHz) antenna in operation in real time without any interruption in service is developed. Such regular measurement will allow the prediction of any serious failures and insure reliable operation of the antenna. All components of the antenna VSWR measurement device was researched so that the whole system could be produced and shown to be accurate in measuring the YSWR of an actual RF repeater in operation, proving it's effectiveness.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.12
• /
• pp.2975-2981
• /
• 2014

Micro-magnetic detection system is used to detect small particles in an automatic transmission valve body, which signal noise and time-delay may occurs in process of signal transmitting and filtering. In this paper, we present the design and implement of a micro-magnetic detection system based on wireless sensor networks in conveyer belt. Micro-magnetic detection system consists of five modules which are magnetic sensor detector, signal processing unit, wireless sensor networks, system control unit and system monitoring unit. Our experimental results show that the proposed wireless micro-magnetic detection system improves both accuracy and time delay compared to the wired system; therefore, it may apply for wireless micro-magnetic detection system by analysis of packet reception rate.

• Journal of Space Technology and Applications
• /
• v.2 no.2
• /
• pp.121-136
• /
• 2022

Automatic Identification System used in ship communication is required for marine control way, including monitoring of vessel operation in coastal and exchanging of information for safety navigation between them. But, it uses a very high frequency band of approximately 160 MHz, and at the same time, due to the curvature of Earth, there is a limit to the communication distance. Several demonstrations were made successfully over satellite, but not much work has been done yet through cube-satellite which has low-orbit at 500 km altitude. Here, we demonstrate a reception test of AIS (automatic identification system) receiver for a cube-satellites using software-defined radio (SDR). We collected AIS data from ship at port of Busan, Korea, using R8202T2 SDR and established to transmit them using Adam-Pluto and Matlab Simulink. The process of weakening the signal strength to a satellite was constructed using attenuator. Through above process, we demonstrated whether AIS data was successfully received from the AIS payload.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.5
• /
• pp.131-138
• /
• 2023

In this paper, a free space optical communication device that can be used in a mobile base station of several km or less was fabricated and its characteristics were investigated. To overcome the loss due to atmospheric transmission, an optical fiber amplifier (EDFA) with an output of 23 dBm or more was used. In order to increase the focusing speed and miniaturization of the laser beam, an optical lens was manufactured, and a transmission lens was designed to have beam divergence within the range of 1.5 to 1.8 [mrad]. A PT module that controls PAN/TILT was fabricated in order to reduce pointing errors and effective automatic alignment between transceiver devices. In this study, Reed-Solomon (RS) code was used to maintain the transmission quality above a certain level. It was manufactured to be able to communicate at a wireless distance of 300m in a weather situation with visibility of 300m. For performance measurement, it was measured using BERT and eye pattern analyzer, and it was confirmed that BER can be maintained at 2.5Gbps.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.11
• /
• pp.1025-1033
• /
• 2011

In this paper, we introduce the contactless power transmission device for transmitting the power with the resonant characteristic of the cavity resonator. When transmitting the power, the contactless power transmission device begins to work in the condition where the transceiver adheres closely. The transceiver is electrically separated because there is no conductive terminal outside and the size of the receiver required for the electric power transmission can be minimized. The cavity resonator comprises slots for the input port and output port in the upper side conductor plate of the cavity and forms the input port and output port using the stripline structure at this upper part. The some of output port is separated from it and the electric power receiver is formed thus the union can be possible. The rest except electric power receiver become the electric power transmitter, which includes the input port of stripline-slot coupling, cavity, and the slot of the output port. If the transmitter and the receiver are combined, they become the form in which the electricity is transferred from the input port to the output port in a cavity resonator. The center frequency of the contactless power transmitter manufactured is 5.782 GHz. and $S_{21}$ is measured as -1.07 dB. It is confirmed that the high electric power transfer rate is approximately 78 %.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.11
• /
• pp.895-901
• /
• 2013

In this paper we propose design of a multi-protocol gateway middleware based on USN. The proposed multi-protocol gateway middleware defined the transmit messages format, and were used the USN module interface protocol for connect to external application MCU using the UART. In this case, the gateway was checks the communication state of Zigbee module with settings information, and setting Zigbee serial PDU format. The experimental results of the proposed multi-protocol gateway middleware were proved the efficiency of integrate protocol gateway to use the multi-protocol gateway than gateway to using the repeater through the power control and communications a controlled experiment.

• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.184-187
• /
• 2016

In this paper, we propose the sensor and the signal duplicator for the automatic building control. Developed duplicator realizes the sensor data collection apparatus and mimics the measured data and, thus, reduces the construction cost by using logical communication layer. Furthermore, the system supports the open protocols and can be associated with HMI(Human Machine Interface) used on the market. Developed duplicator is proved to be functional within the real environment. Measurement error rate, operating temperature, and operating humidity show very good results by the certified testing apparatus and organization.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.46 no.1
• /
• pp.95-103
• /
• 2009

We improve the performance of WCDMA repeater by cancelling the feedback interference radio signal under the fixed point implementation. Floating-point DSP or FPGA to implement the ICS algorithm may have an disadvantage of high cost, To solve this problem, we suggest the ICS algorithm based on LMS under fixed point operation, and show the validity of our results by comparing with the floating-point results through numerical simulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.2
• /
• pp.179-188
• /
• 2015

Testing a radar system in real environment requires a lot of time and cost. Thus various target simulators are developed to evaluate the radar performance and its functions as well. In order to enhance the range resolution and the accuracy for tracking, recent radar system tends to use the wideband signal. In this paper, we summarize two target simulation methods - the direct sampling method with the digital memories and the beat frequency generation for the stretch processing - and suggest the condition to improve their performance for a wideband radar system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.21-24
• /
• 2004

This paper describes a perception of small-obstacle using ultrasonic sensors in a mobile robot. The research on the avoidance of the large-obstacles such as a wall, a large box, etc. using ultrasonic sensors has been generally progressed up to now. But the mobile robot could meet a small-obstacle such as a small plastic bottle of about 1 l in quantity, a small box of 7${\times}$7${\times}$7 cm3 in volume, and so on in its designated path, and could be disturbed by them in the locomotion of the mobile robot. So, it is necessary to research on the avoidance of a small-obstacle. In this paper, the small-obstacle perceiving system was designed and fabricated by arranging four ultrasonic sensors on the plastic plate to avoid a small-obstacle. The small-obstacle perceiving system was installed on the above part of the mobile robot with the slope of 40.7$^{\circ}$ to a horizontal line. The static characteristic test and the dynamic characteristic test were performed to know the information of the used ultrasonic sensors. As a result, the mobile robot with the small-obstacle perceiving system could avoid a small-obstacle, and could move in indoor environment safely.