• Journal of Navigation and Port Research
• /
• v.40 no.6
• /
• pp.385-390
• /
• 2016

ELoran Systems can provide Position, Navigation, and Time services with comparable performance to Global Positioning Systems (GPS) as a back up or alternative system. High timing and navigation performance can be achieved by eLoran signals because eLoran receivers use "all-in-view" reception. This incorporates Time of Arrival (TOA) signals from all stations in the service range because each eLoran station is synchronized to Coordinated Universal Time (UTC). Transmission station information and the differential Loran correction data are transmitted via an additional Loran Data Channel (LDC) on the transmitted eLoran signal such that eLoran provides improved Position Navigation and Timing (PNT) over legacy Loran. In this paper, we propose a technique for adapting the delay time compensation values in eLoran timing receivers to provide precise time comparison. For this purpose, we have designed a system that measures time delay from the crossing point of the third cycle extracted from the current transformer at the end point of the transmitter. The receiver delay was measured by connecting an active H-field, an E-field and a passive loop antenna to a commercial eLoran timing receiver. The common-view time transfer technique using the calibrated eLoran timing receiver improved the eLoran transfer time. A eLoran timing receiver calibrated by this method can be utilized in the field for precise time comparison as a GNSS backup.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.6
• /
• pp.1-8
• /
• 2020

Communication between system modules is applied using the Modbus protocol in industrial sites including smart factories, industrial drones, building energy management systems, PLCs, ships, trains, and airplanes. The existing Modbus was used for serial communication, but the recent Modbus protocol is used for TCP/IP communication.The Modbus protocol supports RTU, TCP and ASCII, and implements and uses protocols in embedded systems. However, the transmission I/O devices for RTU, TCP, and ASCII-based protocols may differ. For example, RTU and ASCII communications transmit on a serial-based communication protocol, but in some cases, Ethernet TCP/IP transmission is required. In particular, since the C language (object-oriented) is used in embedded systems, the complexity of source code related to I/O registers increases. In this study, we designed software that can logically separate I/O functions from embedded devices, and designed the execution logic of each instance requiring I/O processing through a delegate class instance with Modbus RTU, TCP, and ASCII protocol generation. We designed and experimented with software that can separate communication I/O processing and logical execution logic for each instance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1103-1108
• /
• 2016

The development of a variety of sensor technology, users smart phone, the use of motion recognition apparatus such as a console game machines is increasing. It tends to user needs motion recognition-based input device are increasing. Existing motion recognition mouse is equipped with a modified form of the mouse button on the outside and serves as a wheel mouse left and right buttons. Existing motion recognition mouse is to manufacture a small, there is a difficulty to operate the button. It is to apply the motion recognition technology the motion recognition technology is used only pointing the cursor there is a limit. In this paper, use of MEMS-based motion recognition sensor, the body of the two-point operation data by recognizing the operation of the (thumb and forefinger) and generating a control signal, followed by studies on the generated control signal to a wireless transmitting computer input device.

• Journal of Advanced Navigation Technology
• /
• v.24 no.1
• /
• pp.1-8
• /
• 2020

In this research, we develop an airborne equipment radiating S/C-band signal to a target located at a long distance. RF interface of the equipment comprises band-specific transmitters and an broadband antenna to satisfy EIRP(effective isotropic radiated power) requirements. The equipment is in a shape of a POD like an aircraft fuel tank. The measured weight of the equipment is 119.8 kg, the CG(center of gravity) is 1391.35 mm and the MOI(moment of inertia) are 46.07 ± 0.05(I_yy) kg·㎡, 45.36 ± 0.09(I_zz) kg·㎡. All results are found to meet the requirements for aircraft installation. To verify flight safety, EMI(electromagnetic interference) tests (RE102, CE102), environmental tests (high/low temperature operation, altitude), intra-system EMC(electromagnetic compatibility) and HERP(hazards electromagnetic radiation personnel) tests have been conducted and all the test results met the requirements. It is confirmed that the equipment could be mounted on the aircraft by meeting all electrical and mechanical requirements.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.247-250
• /
• 2018

정부는 국내산 풀사료의 경쟁력을 강화하기 위해 풀사료용 기계장비 및 제조비 등의 지원에 해마다 1,000억 이상의 예산을 사용하고 있다. 이에 수반한 보조금의 공정한 집행을 위한 절차와 서류는 매우 복잡하기 때문에 집행 및 정산에 상당한 행정비용이 발생하여 국내 생산 확대의 걸림돌로 적용하고 있는 실정이다. 또한 풀사료는 생산시점의 환경(습도, 온도 등), 수분함유량, 압축압력, 풀사료 품종 등에 따라 품질이 달라지는데 품질기준이 미흡해 유통활성화에 걸림돌이 되고 있다. 풀사료 생산이력 정보 수집에 필요한 센서, IoT 통신기술 등은 상용화 수준에 도달했으나 풀사료 생산현장에 적용하기 위해서는 풀사료 수확기 등과의 통합이 필요하고, 데이터에 기반한 과학적 정책 입안을 위한 기반 데이터 축적이 필요하다. 이를 위해 본 연구에서는 국내산 풀사료의 생산량 증대 및 유통 활성화를 위한 IoT 기반의 풀사료 생산이력관리 시스템을 개발 중으로, 우선 관리 기준이 되는 표준 데이터를 정립해 DB화(化) 하고, 풀사료 수확현장에서 필요한 데이터를 확보하기 위한 생산이력 생성장치 및 생산이력 수집장치와 이를 IoT망을 활용해 전송하기 위한 생산이력 송신장치를 개발하며 수집된 데이터를 통합 데이터베이스화(化) 하여 다양한 사용자에게 유무선 인터넷을 활용해 정보를 제공하는 웹/앱을 개발 중이다. 개발을 위한 핵심 기술로는 풀사료 수확기에 부착된 다양한 센서에서 생성되는 압력 등의 데이터를 실시간으로 취득하는 기술, 제어용 컨트롤러 설계 기술, 센서 데이터 가공 기술, IoT망을 이용한 실시간 전송 기술, 풀사료 통합 DB 구축 기술, Full Stack JavaScript 기술 등이 있다. 본 시스템를 풀사료 현장에 적용하면 풀사료 현장 조사 시간 및 비용 절감, 풀사료 생산/유통/보조 업무 전반의 효율화 및 투명화, 생산이력제 정착으로 풀사료 온라인 유통 활성화 및 물류비 절감, 센서, 측정장치, 표기장치 판매 및 유지보수 등 농업분야 신규사업 창출이 가능하다.

• Journal of Biomedical Engineering Research
• /
• v.23 no.1
• /
• pp.49-60
• /
• 2002

Receive dynamic focusing with an array transducer can provide near optimum resolution only in the vicinity of transmit focal depth. A customary method to increase the depth of field is to combine several beams with different focal depths, with an accompanying decrease in the frame rate. In this Paper. we Present a simultaneous multiple transmit focusing method in which chirp signals focused at different depths are transmitted at the same time. These chirp signals are mutually orthogonal in a sense that the autocorrelation function of each signal has a narrow mainlobe width and low sidelobe levels. and the crossorelation function of any Pair of the signals has values smaller than the sidelobe levels of each autocorrelation function. This means that each chirp signal can be separated from the combined received signals and compressed into a short pulse. which is then individually focused on a separate receive beamformer. Next. the individually focused beams are combined to form a frame of image. Theoretically, any two chirp signals defined over two nonoverlapped frequency bands are mutually orthogonal In the present work. however, a tractional overlap of adjacent frequency bands is permitted to design more chirp signals within a given transducer bandwidth. The elevation of the rosscorrelation values due to the frequency overlap could be reduced by alternating the direction of frequency sweep of the adjacent chirp signals We also observe that the Proposed method provides better images when the low frequency chirp is focused at a near Point and the high frequency chirp at a far point along the depth. better lateral resolution is obtained at the far field with reasonable SNR due to the SNR gain in Pulse compression Imaging .

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.12
• /
• pp.2641-2646
• /
• 2009

The more growing on home automation system at automatic control, the more efficiency required for energy consumption and for recycling energy in near future. Heating is essential in general apartment. Heating method is two types in apartment. One uses electricity, and other one uses warm water. If use electricity, is not efficient by rise of electric charges. But, It can reduce much in expense aspect, if use warm water. When use warm water, temperature of warm water is not equal from all pipe parts. Therefore, indoor tempera can be unequal with set point. Solution of these problems is as following. Temperature sensor in warm water attach pipe. The measured temperature transmits by real time. Temperature of warm water controls in receiver side. In this paper, we propose an automatic temperature transmission system for the heating pipe at home, that is a low-power based, and supply the energy source from a small AC motor resided in bottom cement mortal. The proposed system is used in power mechanism from a collision process of water-jet using propeller water-difference and also designed a CPU module by Atmega8 at ATMEL co., Inc. and a communication module by CC1020 at Chipcon co., Inc.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.84-84
• /
• 2011

저수지에서 수체의 거동정보는 저수지관리를 위해 매우 중요하며, 이를 수리 및 수질모형에 적용하여 다양한 예측에 활용할 수 있는 기본적인 정보이다. 그러나 저수지 수체의 흐름은 매우 느리고 조사시기에 따라 혹은 수심에 따라 영향을 받으며, 바람 등 외부요인에도 영향을 받게 됨으로 정확한 측정에 많은 어려운 문제가 있다. 따라서 보다 정확한 측정을 위해서는 최신의 기술이 적용되어야 한다. 현장조사에 적용한 저수지 수체거동조사장비(drifter)는 수체의 유동을 관측하는 장치로 GPS 및 Drogue를 장착한 장치가 저수지 수체의 흐름에 따라 이동하면서 위치정보를 무선통신으로 실시간 전송할 수 있도록 만들어진 장치이다. 수체흐름 측정장치는 크게 수체거동정보 생산부이 시스템과 수집서버 및 데이터베이스 서버로 구성되어 있다. 현장 조사시에는 부이에 장착되어 있는 GPS를 통해 현재의 위치가 매번 정해진 시간 간격마다 본체 내부의 메모리에 저장되며, 측정자가 설정한 시간간격으로 위치정보를 수신국으로 전송하도록 구성되어 있다. 수체이동부이의 데이터 수신은 CDMA를 통해 송신된 메일 데이터를 자체적으로 수집하여 데이터형태로 변환한 뒤 실시간으로 표출하고 저장되며, 최대 10개의 부이를 동시에 추적 및 모니터링할 수 있게 구성되어 있다. 본 연구는 용담댐저수지에서 평갈수기 및 풍수기로 구분하여 수체거동을 조사하였다. 평갈수기 조사는 2010년 4월부터 6월까지 총 3차례에 걸쳐 실시하였으며, 풍수기 조사는 8월에 3차례에 걸쳐 실시하였다. 수집된 자료에 의하면 평갈수기 drifter의 평균 속도는 2.25 cm/sec, 최고 속도는 3.46 cm/sec, 최저 속도는 1.15 cm/sec로 나타났으며, 풍수기 조사에서는 평균 속도 2.0 cm/sec, 최고 속도는 2.5 cm/sec, 최저 속도는 1.29 cm/sec로 조사되어 평갈수기와 풍수기간 저수지 수체의 이동속도는 유사한 것으로 평가되었다. 그러나 수기별 조사는 보다 더 많은 정보가 필요하며, 수심에 따른 차이도 있을 것으로 판단되어 좀더 다양한 조사가 수행되어야 보다 정확한 결과를 도출할수 있을 것으로 판단된다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.791-793
• /
• 2016

In the development of various types of sensor technology, the general users smartphone, the environment is increased, which can be seen in contact with the movement recognition device, such as a console game machine (Nintendo Wii), an increase in the user needs of the action recognition-based input device there is a tendency to have. Mouse existing behavior recognition, attached to the outside, is mounted in the form of mouse button is deformed, the left mouse was the role of the right button and a wheel, an acceleration sensor (or a gyro sensor) inside to, plays the role of a mouse cursor, is to manufacture a compact, there is a difficulty in operating the button, to apply a motion recognition technology is used to operate recognition technology only pointing cursor is limited. Therefore, in this paper, using a MEMS-based motion-les Koguni tion sensor (Motion Recognition Sensor), to recognize the behavior of the two points of the human body (thumb and forefinger), to generate the motion data, and this to the foundation, compared to the pre-determined matching table (moving and mouse button events cursor), and generates a control signal by determining, were studied the generated control signal input device of the computer wirelessly transmitting.

• Journal of Aerospace System Engineering
• /
• v.12 no.2
• /
• pp.37-45
• /
• 2018

A two-axis gimbal-type antenna for a Compact Advanced Satellite (CAS) is used to efficiently transmit high resolution image data to a ground station. In this study, we designed the structure of a two-axis gimbal-type antenna while applying a launch lock device to secure its structural safety under a launch environment. To validate the effectiveness of the structural design, a structural analysis of the antenna was performed. First, a modal analysis was performed to investigate the dynamic responses of the antenna with and without the mechanical constraints of the launch lock device. In addition, a quasi-static analysis was performed to confirm the structural safety of the antenna structure and bolt I/Fs between the antenna base and the satellite. The suitable range of constraint force on the launch lock device was also determined to ensure the structural safety and mechanical gapping of the ball & socket interfaces, which places multi-constraints on the azimuth and elevation stage of the antenna.