• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.2
• /
• pp.269-288
• /
• 1999

현재 골 유착성 임플랜트는 안전하고 유용한 보철 수복 분야의 하나로 자리잡아 가고있다. 과거 완전 무치악 환자에게 있어서 저작 기능의 회복이란 면에 중점을 두었던 경향에서 현재 골유착 임플랜트의 높은 성공률에 의해 부문 무치악, 단일치 수복에 까지 다양하게 사용되고 있다. 특히 심미성과 인접치의 손상을 가하지 않는다는 면에서 단일치 수복에서 골유착 임플랜트 치료에 관심이 모아지고 있다. 단일치 수복에 있어서 심미성이 중요한 문제로 대두되면서 이런 수복에 사용될 수 있는 다양한 계통의 임플랜트들이 개발되어 사용되고 있다. 이중 가장 기본적인 Branemark 계통의 CeraOne 지대주, 최근에 개발된 전부도재 지대주인 CerAdapt 전부주조 지대주인 UCLA 계통등은 높은 성공률을 보이며 많이 사용되고 있다. 임상가들에 의해 나사유지형 보철물이 착탈성이란 관점에서 선호되고 있다. 시멘트유지형 보철물에서는 나사공이 없는 온전한 교합면을 유지한다는 면과 교합력을 받는 면적에 있어서 더 넓은 면을 가진다는 점등 더 많은 장점을 가진다고 주장하는 사람도 있다. 임상가들의 기호에 의해 선택되어지는 나사 유지형과 시멘트 유지형에 있어서 교합력이 야기하는 하중하에서 각각의 응력 분포를 분석할 필요성이 요구되었다. 이 연구는 단일치 수복에 사용되는 CeraOne, CerAdapt UCLA 계통에서 각각의 나사 유지형과 시멘트유지형에서의 응력분포를 삼차원 유한요소법으로 분석하고 상부 구조물에 가해지는 수직하중, 수평 하중, 경사 하중에 의해 야기되는 응력을 비교 분석한 것이다. 본 연구의 연구 결과는 다음과 같다. 1. CeraOne, CerAdapt, UCLA 지대주 모두 시멘트유지형보다 나사유지형에서 응력집중이 컸다. 2. CeraOne 시멘트유지형인 1번 모델에서 응력분산이 유리하였고, UCLA 나사 유지형인 6번 모델에서 가장 불리하였다. 3. 모든 모델에서 고정체 경부에서 가장 큰 응력 집중이 있었고 이것은 UCLA 지대주에서 가장 컸다. 4. 상부 구조물에서 주된 응력의 집중은 교합면에서 일어났다. 5. 골은 상부 피질골, 즉 고정체경부와 만나는 부위에서 가장 큰 응력의 집중이 일어났으며 수평, 경사 하중시 응력집중 양상은 힘을 가한 쪽의 반대쪽 고정체 경부에 응력이 집중되는 양상을 보였다. 6. 전체 모델과 골, 고정체 모두에서 수평 하중과 경사 하중시 보다는 수직 하중시 더 적은 응력값을 보였다.

• Resources Recycling
• /
• v.29 no.2
• /
• pp.8-17
• /
• 2020

In this study, adsorption and desorption characteristics of pulverized waste paper-mulberry pellet and bast fiber were measured to confirm the applicability to humidity control products. Paper-mulberry powder was classified by 710-355㎛, 355-100㎛, 100-45㎛ and less than 45㎛ and used in experiment. Specific surface area increased from 1.02㎡/g to 1.35㎡/g as the particle size decreased from 710㎛ to under 45㎛. Adsorption and desorption performance decreased in the order of 355-100㎛, 710-355㎛, 100-45㎛, less than 45㎛ and bast fiber, adsorption content on each particle sizes were 141.1g/㎡, 147.1g/㎡, 135.7g/㎡, 129.0g/㎡ and desorption content were 117.2g/㎡, 123.6g/㎡, 110.2g/㎡, 93.3g/㎡. As a result, adsorption and desorption performance of paper-mulberry powder were superior to those of the bast fiber and these phenomenon can be considered that it caused by pore distribution in pellet and damage of fiber.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.3
• /
• pp.311-322
• /
• 2022

This study performed 4-point flexural tests of reinforced concrete to which was attached a distributed optical fiber sheet and carbon fiber reinforced polymer (CFRP) sheets in order to assess the effect of the CFRP sheets and the applicability of a BOTDR sensor simultaneously. To evaluate the reinforcing effect, various degrees of CFRP sheet attachment were manufactured, and to evaluate the sensing ability, strains obtained from a BOTDR sensor were compared with strains measured from electric resistance strain gauges that were attached to the concrete surface. From the results, the reinforcing effects were evidently different according to the attachment type of the CFRP sheets, and it was confirmed that the main influencing factor on the reinforcing effect was the type of attachment rather than the attachment area. The reinforced concrete structural behavior was visualized with strains measured from the BOTDR sensor as load increased, and it was identified that load was concentrated in the CFRP reinforced area. Strains from the BOTDR sensor were similar to those from the electric resistance strain gauge; thereby a BOTDR sensor can be effective in the analysis of structural behaviorsof massive infrastructure. Finally, the strain from a BOTDR sensor was high where CFRP sheet fall-off occurs, and it would therefore be efficient to track local damage locations of CFRP sheets by utilizing a BOTDR sensor.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.327-327
• /
• 2021

하수재이용에서 전처리 막여과 공정은 완벽한 고액분리로 인해 후단 역삼투막 손상을 줄일 수 있는 공정으로 각광을 받고 있다. 일반적으로 막여과 공정은 여과->물리세정->충진->여과 와 같은 제막사에서 제공하는 운전 사이클에 맞춰 적용하고 있으며 유지세정 역시 1회/일 또는 1회/주 단위로 정해진 범위에서 수행되고 있다. 이러한 운전 방식은 시시각각 변화하는 막 유입수질에 적절하게 대응하지 못해 장기적으로 막오염 발생에 따른 생산수량 감소는 물론 막오염 제거를 위한 화학세정 주기가 짧아져 전체적인 생산수량이 감소하는 원인이 되고 있다. Raffine(2012)에 따르면 가역적 막오염의 경우 Flux 증가에 큰 영향이 없으나 비가역적 막오염은 Flux 증가에 따라 급격히 증가한다고 보고하고 있으며 이는 제한된 분리막 면적당 처리수 생산량을 증가시키기 위해 비가역적 막오염의 발생량을 줄이는 것이 필요하며 이를 위해 주기적인 강화역세(Chemical Enhanced Backwashing, CEB)가 도입되고 효율적인 유지세정 방법에 대한 연구가 진행되고 있다. 당사에서는 일산에 있는 I 수질복원센터내에 25 m³/일 규모의 막여과 하수재이용 파일롯 플랜트를 설치하고 막여과 하수재이용 공정의 운영 효율을 높이기 위하여 W사에서 개발한 IntelliFluxControl(IFCr) 소프트웨어를 이용하여 하수재이용 막여과 성능을 확인 하였다. IFCr은 실시간으로 변화하는 수질에 따른 막오염 정도에 따라 역세 강도 및 빈도와 CEB 적용 정도를 변화시켜 분리막 운전의 효율을 높일 수 있는 운영 소프트웨어이다. I 수질복원센터의 하수 방류수를 막여과 유입수로 적용하여 40 LMH를 기준으로 IFCr을 적용하지 않은 경우 23.7일 운전 가능하였으나 IFCr을 적용한 경우 50일 연속 운전이 가능하였다. 또한 역세척수를 운전 기간 동안 약 50 m³을 사용한 반면 IFCr을 적용한 경우 이에 절반 수준인 24.1 m³ 만 사용하여 회수율이 91%에서 95%로 증가한 것을 확인 할 수 있었다. 본 연구의 결과는 기존의 제막사에서 제시하는 막 공정 운영방법을 탈피하여 분리막이 갖고 있는 성능을 최대한 끌어 올릴 수 있는 연구 결과라고 판단되며 향후 스케일 업 연구를 통해 실제 플랜트에 적용 가능성이 확인 될 경우 시설의 설치 막모듈 개수와 유지관리비를 동시에 절감할 수 있는 기술이 될 수 있을 것이다

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.1
• /
• pp.21-32
• /
• 2023

Interrill erosion dominates in forest areas, and the erosion rate in surface-disturbed areas is significantly increased by the development and expansion of rill. In this study, soil erosion experiments using simulated rainfall and inflow were performed to understand the development and the micromorphological changes of rill on steep slopes. The characteristic factors of the micromorphology, such as the rill cross section, rill volume, rill density, rill order, and rill sharpness, were analyzed according to steepness and location (upper or lower) of slope. The head-cut of the simultaneous incised rills by rainfall simulation moved rapidly upslope, and the randomly developed rills expanded deeply and widely with their connection. The rill cross section evolved to downslope gradually increased. The rill volume occupied about 78 % of the sediment volume, confirming that the contribution of the sediment from the rill erosion is greater than that of the interrill erosion. Although the rate of increase in rill order slowed as the slope increased, the total length and density of the rill generally increased. As the slope increased from 15° to 20°, the bed incision of rills became larger than the sidewall expansion, and the rill sharpness increased by 1.6 times. The runoff coefficient on the lower slope decreased by 12.3 % than that on the upper slope. It was evaluated that the subsoil exposures and formation changes by the rill expansion increased the infiltration rate. Although the sediment accompanying the rills generally increased with slope increase, it was directly influenced by the hydraulic velocity of enhanced rill with the local convergence and expansion in the process of the rill evolution.

• Korean Chemical Engineering Research
• /
• v.62 no.1
• /
• pp.27-35
• /
• 2024

Fuel gases such as methane and propane are used in explosion hazardous area of domestic plants and can form non-uniform mixtures with the influence of process conditions due to leakage. The fire-explosion risk assessment using literature data measured under uniform mixtures, damage prediction can be obtained the different results from actual explosion accidents by gas leaks. An explosion characteristics such as explosion pressure and flame velocity of non-uniform gas mixtures with concentration change similar to that of facility leak were examined. The experiments were conducted in a closed 0.82 m long stainless steel duct with observation recorded by color high speed camera and piezo pressure sensor. Also we proposed the quantification method of non-uniform mixtures from a regression analysis model on the change of concentration difference with time in explosion duct. For the non-uniform condition of this study, the area of flame surface enlarged with increasing the concentration non-uniform in the flame propagation of methane and was similar to the wrinkled flame structure existing in a turbulent flame. The time to peak pressure of methane decreased as the non-uniform increased and the explosion pressure increased with increasing the non-uniform. The ranges of K_G (Deflagration index) of methane with the concentration non-uniform were 1.30 to 1.58 [MPa·m/s] and the increase rate of K_G was 17.7% in methane with changing from uniform to non-uniform.

• Composites Research
• /
• v.15 no.4
• /
• pp.23-31
• /
• 2002

The two dimensional size effect of specimen gauge section ($length{\;}{\times}{\;}width$) was investigated on the compressive behavior of a T300/924 $\textrm{[}45/-45/0/90\textrm{]}_{3s}$, carbon fiber-epoxy laminate. A modified ICSTM compression test fixture was used together with an anti-buckling device to test 3mm thick specimens with a $30mm{\;}{\times}{\;}30mm,{\;}50mm{\;}{\times}{\;}50mm,{\;}70mm{\;}{\times}{\;}70mm{\;}and{\;}90mm{\;}{\times}{\;}90mm$ gauge length by width section. In all cases failure was sudden and occurred mainly within the gauge length. Post failure examination suggests that $0^{\circ}$ fiber microbuckling is the critical damage mechanism that causes final failure. This is the matrix dominated failure mode and its triggering depends very much on initial fiber waviness. It is suggested that manufacturing process and quality may play a significant role in determining the compressive strength. When the anti-buckling device was used on specimens, it was showed that the compressive strength with the device was slightly greater than that without the device due to surface friction between the specimen and the device by pretoque in bolts of the device. In the analysis result on influence of the anti-buckling device using the finite element method, it was found that the compressive strength with the anti-buckling device by loaded bolts was about 7% higher than actual compressive strength. Additionally, compressive tests on specimen with an open hole were performed. The local stress concentration arising from the hole dominates the strength of the laminate rather than the stresses in the bulk of the material. It is observed that the remote failure stress decreases with increasing hole size and specimen width but is generally well above the value one might predict from the elastic stress concentration factor. This suggests that the material is not ideally brittle and some stress relief occurs around the hole. X-ray radiography reveals that damage in the form of fiber microbuckling and delamination initiates at the edge of the hole at approximately 80% of the failure load and extends stably under increasing load before becoming unstable at a critical length of 2-3mm (depends on specimen geometry). This damage growth and failure are analysed by a linear cohesive zone model. Using the independently measured laminate parameters of unnotched compressive strength and in-plane fracture toughness the model predicts successfully the notched strength as a function of hole size and width.

• Journal of the Korea Concrete Institute
• /
• v.25 no.5
• /
• pp.485-496
• /
• 2013

In recent years, frequent terror or military attacks by explosion or impact accidents have occurred. Examplary case of these attacks were World Trade Center collapse and US Department of Defense Pentagon attack on Sept. 11 of 2001. These attacks of the civil infrastructure have induced numerous casualties and property damage, which raised public concerns and anxiety of potential terrorist attacks. However, a existing design procedure for civil infrastructures do not consider a protective design for extreme loading scenario. Also, the extreme loading researches of prestressed concrete (PSC) member, which widely used for nuclear containment vessel, gas tank, bridges, and tunnel, are insufficient due to experimental limitations of loading characteristics. To protect concrete structures against extreme loading such as explosion and impact with high strain rate, understanding of the effect, characteristic, and propagation mechanism of extreme loadings on structures is needed. Therefore, in this paper, to evaluate the impact resistance capacity and its protective performance of bi-directional unbonded prestressed concrete member, impact tests were carried out on $1400mm{\times}1000mm{\times}300mm$ for reinforced concrete (RC), prestressed concrete without rebar (PS), prestressed concrete with rebar (PSR, general PSC) specimens. According to test site conditions, impact tests were performed with 14 kN impactor with drop height of 10 m, 5 m, 4 m for preliminary tests and 3.5 m for main tests. Also, in this study, the procedure, layout, and measurement system of impact tests were established. The impact resistance capacity was measured using crack patterns, damage rates, measuring value such as displacement, acceleration, and residual structural strength. The results can be used as basic research references for related research areas, which include protective design and impact numerical simulation under impact loading.

• Food Science and Preservation
• /
• v.21 no.2
• /
• pp.264-275
• /
• 2014

This study evaluated the improving efficacy of Lespedeza cuneata ethanol extract on skin photoaging induced by ultraviolet (UV) irradiation. The total polyphenol and flavonoid contents of the extract were respectively $134.98{\pm}1.70$ and $16.20{\pm}0.05$ mg/g, respectively. The superoxide anion radical scavenging activity and electron-donating ability of the extract were shown to be dependent on concentration, and the antioxidant ability was shown to be more effective in superoxide anion radical scavenging activity than in electron-donating ability under the same concentration conditions. In the in vivo test conducted using hairless mouse with skin photoaging induced by UVB irradiation, the skin erythema of the groups treated with the extract (AS) reduced to 28% of the control, and the skin moisture content increased to 131%.. The extract treatment of the UV-damaged skin improved the morphological and histopathological state of the skin. Furthermore, the SOD, GST and CAT activities in the skin tissue of the AS group increased, and the XO activity and TBARS generation decreased. With regard to the genes related to the photoaging skin, the expression of PAK, p38, c-Fos, c-Jun, TNF-${\alpha}$ and MMP-3 in the skin of the AS group were found to have decreased. It was therefore concluded that Lespedeza cuneata ethanol extract can reduce wrinkle formation in the skin due to the regulation of the gene expression caused by the exposure to UVB light.

• Korean Journal of Breeding Science
• /
• v.42 no.1
• /
• pp.75-86
• /
• 2010

End-use properties of 26 Korean wheat cultivars (KWC) were evaluated to assess consumer satisfaction with 6 imported wheat and 5 commercial wheat flours. In end-use quality testing of cooked noodles, Absorption of noodle dough sheet of ASW (Australian standard white) was similar to Anbaek, Eunpa, Gobun, Hanbaek, Jeokjoong, Jonong, Namhae, and Sukang. Thickness of noodle dough sheet of KWC was showed thin difference. In imported wheat and commercial flour, Commercial flour for baking cookie (Com5) with lower protein flour was lower than those flours. In lightness of prepared noodle dough sheet, Lightness value ($L^*$) of KWC was lower than those of Commercial flour for making white salted noodle (Com1), commercial flour for making for yellow alkaline noodle (Com2), and commercial flour for multi-purpose (Com4). Lightness value ($L^*$) showed significantly negative correlations with particle size of flour, ash, damaged starch, and protein content. Hardness of cooked noodles positively correlated with protein content. In texture of cooked noodles, Hardness of Com1 was similar to that of Alchan, Dahong, Jeokjoon, and Sukang. Also, hardness of Com2 was similar to that of Gobun, Jokyung, Jonong, Keumkang, and Namhae. In end-use quality of bread, bread loaf volume of commercial flour for making bread (Com3) was similar to Alchan, Jokyung, Keumkang, and Namhae but firmness was low. Bread volume showed better relationships with higher SDS-sedimentation volume, longer mixing time of mixograph, higher height of dough during development. Firmness of crumb was negatively correlated with bread volume. Diameter of cookie showed significantly negative correlations with particle size of flour, damaged starch, and protein content. Also, Top gain score became higher as the increase diameter of cookie. In end-use quality testing of cooked cookie, Cookie diameter of Com5 was similar to that of Dahong, Geuru, Olgeuru, Tapdong, and Uri but top grain was low.