• 전기의세계
• /
• v.61 no.10
• /
• pp.17-27
• /
• 2012

• 전기의세계
• /
• v.38 no.5
• /
• pp.34-42
• /
• 1989

포항 방사광가속기의 입사장치인 2.5GeV 양전자 선형 가속기에서 양전자를 포획하는 solenoid lens와 접속용 사극자석의 system에 대하여 살펴보았다. 이론적 결과를 토대로 하여 이를 PLS 양전자 injector에 적용한 결과를 소개하고자 한다.

• Proceedings of the Korea Society of Design Studies Conference
• /
• 2001.05a
• /
• pp.62-63
• /
• 2001

• Proceedings of the Korean Vacuum Society Conference
• /
• 2006.02a
• /
• pp.41-41
• /
• 2006

• The Transactions of the Korea Information Processing Society
• /
• v.3 no.7
• /
• pp.1868-1879
• /
• 1996

There are limitations to process high bandwidth traffic in B-ISDN with mesh- topology single bus architecture of current mobile communication system. And, it is impossible to import ATM switch using fixed length packet rather than variable length packet. Some implementations are able to process variable length packet, but there are some problems such as pre-processing for synchronization and bit delay. In this paper, we design a concentrator that can manipulate variable length packet without additional pre-process. There is on bit delay for packet starting signal in input interface, So it is more efficient to process packets, such that the concentrator can reduce he processing time as $\ulcornerlog2N\lrcorne＋1$ bit-time rather than N bit-time delay in ordinary concentrator. It is expected that the mobile communication system with partial mesh topology bus adopting the knockout switch architecture can process high bandwidth traffic in B-ISDN.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.5
• /
• pp.507-515
• /
• 2015

This study was conducted to develop and verify a torque application device for use in a mechanical power-circulation test rig for 5.5 MW wind turbine gearboxes. The design and analysis of the torque application device was conducted. In addition, the torsional stiffness of the test rig was calculated using the rotational angle measurements for each of the components. The calculated stiffness of the test rig was $231.13kN{\cdot}m/rad$ for a clockwise torque application. The rated torque can be applied when the stiffness of the gearbox is greater than $1,064,400kN{\cdot}m/rad$ for a clockwise torque application. Because of the limited rotational angle of the test rig, the potential application of the rated torque is determined according to the torsional stiffness of the test gearbox.

• Journal of the Korean Society of Radiology
• /
• v.9 no.1
• /
• pp.55-59
• /
• 2015

Research about the proton nuclear reaction is actively achieving on the proton therapy including material development of fusion reactor. The proton induced gamma ray energy(2754, 1386 keV) spectrum of 27Al(p,3p+n)24Na reaction was measured with 100 MeV high energy proton beam. The proton beam in the experiment was derived from 100 MeV proton linear accelerator in the KOMAC. We measured the gamma ray intensity ratio of the decay level from the energy spectrum. The previous results have been compared with the current result. Strength of measured gamma rays will provide very important information though decide high energy gamma radiation detection efficiency.

• Journal of the Korean Vacuum Society
• /
• v.20 no.1
• /
• pp.1-6
• /
• 2011

A sudden step change is observed in the vertical position readings from beam position monitors (BPMs) mounted at the several sector vacuum chambers of Pohang Light Source. To study the source of this sudden step change, we measured the RF transmission scattering matrix (S21) through the pickup electrodes of BPMs mounted at the both ends of the sector vacuum chamber. The measured $S_{21}$ graph of the sector vacuum chambers suffering sudden step change has a peak in the BPM operation frequency bandwidth. Otherwise that of the other sector vacuum chambers doesn't have a peak. It is shown by the numerical simulation that the peak found in the BPM operation frequency bandwidth corresponds to the longitudinal harmonic of transverse electric resonance mode.

• 한국ITS학회:학술대회논문집
• /
• 2008.11a
• /
• pp.289-294
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.617-618
• /
• 2012