• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.311-314
• /
• 2007

The experimental method of measuring dynamic properties of structures was presented. The method is based on the flexural wave propagation characteristics. Using the method, change in structural dynamic properties due to damage is measured. The crack has much more significant impact on the strain energy than the inertial effects. From this, the sensitivity of the dynamic stiffness on the crack location is estimated by calculating the strain energy. When the wave propagates, the strain and kinetic energies shows cyclic changed over space. The crack that occurred at locations where the wave energy is in the form of the potential energy affected most significantly the wave propagation characteristics. The effects of crack location on the wave propagation were used to determine the crack location.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.247-251
• /
• 2001

Nowadays, base isolation systems such as lead-rubber bearing, elastomer bearing and sliding bearing have been installed to the various structures to prevent the disaster from seismic. The performance of base isolation system have been well proved by model-scale experiments and numerical analysis. However. the seismic response data measured at real large base-isolated structures is still insufficient. This paper presents a seismic monitoring system, acquiring real-time acceleration signals up to 32 channels, displaying time history and spectrum of the signals, storing the acquired data at a PC hard disk, and replaying the saved data. Moreover, the system can be operated without any limitation for monitoring period by automatic management of stored data file. The developed system has been installed at a real base-isolated building using lead-rubber bearings and we expect its seismic response data with ground motion signal can be well licquired in case of earthquake occurrence.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.739-742
• /
• 2014

In the process of MLCC manufacturing, MLCC stacking process is the key process of making high quality MLCC. Since MLCC is small components, the entire process of MLCC stacking process is minute and sensitive to micro errors. To prevent micro error, we suggest condition-based monitoring which quantifies error based on feature extraction and quantifying error method. As results, it has been shown that the suggested algorithm has effectiveness of condition based monitoring of MLCC stacker.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.11
• /
• pp.1106-1112
• /
• 2012

This paper deal with a technique for monitoring machining conditions by measuring the vibration of cutting forces at milling machining. The vibrations of cutting forces in milling process were measured and analyzed to be related with processing parameters. The magnitude of cutting force is linearly proportional to the feed rate and cutting depth, and frequency of cutting force is linearly proportional to the rotating speed. Wired and wireless communication methods were applied in transmitting the measured vibration signals and the two methods were compared. The magnitude of the vibration signals transmitted by the wireless communication method was similar to that transmitted by the wired communication method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.619-624
• /
• 2004

In this research, the structural health monitoring method using wavelet packet analysis and artificial neural network (ANN) is developed. Wavelet packet Transform (WPT) is applied to the response acceleration of a 3 element-cantilever beam which is subjected to impulse load and Gaussian random load to decompose the response signal, then the energy of each component is calculated. The first ten largest components in magnitude among the decomposed components are selected as input to an ANN to identify the damage location and severity. This method successfully predicted the amount of damage in the structure when the structure is subjected to impulse load. However, when the beam is subjected to Gaussian random load which can be considered as ambient vibration it did not yield satisfactory results. This method is applicable to structures such as machinery gears that are subjected to repetitive loads.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.2
• /
• pp.60-66
• /
• 2009

The acceleration noise is valuable index to monitor traffic stability. However, the previous study was performed for the acceleration noise of individual vehicle. The consideration of the acceleration noise for vehicle in the network has not been studied yet. This paper proposes a new macroscopic traffic flow monitoring method based on applying network acceleration noise.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2011.05a
• /
• pp.299-300
• /
• 2011

• Proceedings of the Korea Information Processing Society Conference
• /
• 2003.11a
• /
• pp.77-80
• /
• 2003

본 논문은 웹 기반의 원격 보수유지 시스템을 구현하기 위한 첫 단계의 일부로서 원격 모니터링을 위한 웹 기반 기술 구축에 관한 것이다. 원격 작업장에 있는 정밀 기계 장비(CNC)를 대상으로 하여 작업장이 아닌 장소에서도 온도, 진동, 소음, 영상 데이터 등을 모니터하고 또한 장비의 상태를 진단할 수 있는 시스템 구축에 대한 것이다. 원격 사용자는 인터넷을 통해 어디에서나 생산 현장에 있는 로칼 서버에 접속하여 해당 장비를 모니터 및 상태 진단이 가능한 시스템을 구현하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.81-84
• /
• 2007

In this paper, fiber optic sound and vibration monitoring sensor which is latticed shape structure based on Sagnac interferometer is fabricated and tested in laboratory conditions. To detect external vibrations surface mounted fibers on the latticed steel wire fence with a dimension of 170cm by 180cm is used. To detect external sound frequency the tightened fiber optic itself wire netting fence with a dimension of 50cm by 50cm is used. Experiments for the detection of the excited vibration and sound signals were performed. A small vibrator induced external vibration signal and it is applied to the latticed structure in the range of 100Hz to several kHz. External sound signal applied to the fiber optic sensor net using non-directional sound speaker. The detected optical signals were compared and analyzed to the detected both accelerometer and microphone signals in the time and frequency domain. Based on the experimental results, distributed fiber optic sensor using Sagnac interferometer detected effectively external vibration and sound signal and had a good performance. This system can be expanded to the monitoring of a significant system and to the structural health monitoring system.

• Journal of Korean Society for Geospatial Information Science
• /
• v.22 no.4
• /
• pp.165-173
• /
• 2014

Open-pit mining method, is safe relatively work as compared with underground mining. And high yield, low production cost, has the advantage that it can provide a lot of production. But deforestation, tailings and slag deposition, mineral debris, dust, water, noise, land subsidence, sediment runoff discharge, I have internalized environmental disaster predisposing factors, such as landslides. Thus, it may be noted, also by typical environmental regulations. We try to deal with the changes in open pit terrain and environment related issues. Then, use the recovery period and the open pit mine and ecology off the gun, environment-friendly development of accurate monitoring methods, systems of this development is required. The use of open platforms and open source GIS tools have been developed during this period, it needs to develop spatial information environment monitoring system open pit mine construction.