• Journal of Korean Society of Steel Construction
• /
• v.10 no.4 s.37
• /
• pp.629-639
• /
• 1998

This paper summarizes the results of full-scale cyclic seismic performance tests on three column-tree type steel moment connections. Each test specimen consisted of a $H-600{\times}200$ beam and a $H-400{\times}400$ column of SS41 (SS400). Key parameter included was column PZ (panel zone) strength relative to beam strength. The seismic performance of specimen with stronger PZ tended to be inferior. Total plastic rotations available in the specimens ranged from 1.8 to 3.0 (% rad). The limited test results in this study seem to support the speculation that permitting PZ yielding shall be more beneficial to enhancing total plastic rotation capacity of the moment connection. Beam flange fracture across the heat affected zone and divot-type pullout of the column flange were observed in the tests. A conceptual mechanical model consistent with observed test results was also sought.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.93-93
• /
• 2009

본 연구에서는 EGW, FCAW 공정 적용에 따른 고강도 극후판 EH36-TMCP강 용접부의 역학적 거동 및 파괴인성 $K_{IC}$ 을 규명하기 위해, 먼저 열분포, 열탄소성 수치해석을 통하여 용접부의 역학적 거동(용접잔류응력, 소성변형율 등의 크기, 분포, 발생기구)을 고찰하였다. 그리고 이때 얻어진 잔류응력을 초기응력으로 하여, 잔류응력과 외력의 복합하중에 대한 파괴인성 $K_{Ic}$ 특성을 해석하였다. 용접공정별 균열이 존재하는 용접부의 파괴기준을 살펴보면, EGW용접부의 경우가 FCAW용접부의 경우에 비해 균열의 성장이 다소 용이하여 $K_{IC}$ 값이 다소 낮게 나타났다. EGW용접부의 파괴인성 $K_{IC}$ 경우 중첩된 경우(복합하중)가 순수 외력만 작용하는 경우보다 파괴 인성치가 다소 감소하는 경향을 보이고, a/W가 작을 경우 중첩의 경우가 순수 외력만의 경우보다 파괴인성치 차이가 크나, a/W가 증가함에 따라 그 차이가 점차 없어지는 것으로 나타났다. 반면, FCAW용접부의 경우 균열길이가 작은 범위에서는 중첩된 경우가 순수 외력만 작용 할 경우보다 파괴 인성치가 다소 증가함을 보이지만, a/W가 증가함에 따라 순수 외력만의 작용의 경우와 중첩의 경우의 파괴인성 차이가 없는 것으로 나타났다.

• Journal of the Korean Institute of Gas
• /
• v.3 no.3 s.8
• /
• pp.1-8
• /
• 1999

Three-point bending fatigue properties of austenitic 304 stainless steel sheets were investigated at room temperature and LNG temperature($-162^{\circ}C$) in the strain range from 0.43 to $1.7\%$. The fatigue properties at $-162^{\circ}C$ were superior to those at room temperature due to the higher volume fractions of deformation-induced martensite. The cyclic hardening behavior owing to the deformation- induced martensite transformation was detected in both specimens. In room temperature testing, the mean load amplitude increased steadily with cycles, meaning that cumulative plastic incubation strain was required for martensite transformation. On the contrary, in $-162^{\circ}C$ tested specimen, the mean load amplitude increased rapidly within a few cycles due to the rapid transformation of martensite, and slightly decreased after the maximum is reached probably due to dynamic recovery.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.5
• /
• pp.625-632
• /
• 2008

In the companion paper (Model Development), an analytical model estimating the available rotation capacity of fully restrained beam-column connections in special steel moment-resisting frames was proposed. In this paper, two limit states were considered as the connection rotation capacity criteria: (i) strength degradation failure when the strength falls below the nominal plastic strength due to the local buckling of the beam's cross-section and (ii) low-cycle fatigue fracture caused by plastic strain accumulation at the buckled flange after only a few cycles of high-amplitude deformation. A series of analyses are conducted using the proposed model with two limit states under monotonic and cyclic loadings. Beam section geometric parameters, such as flange and web slenderness ratios, varied over the practical ranges of H-shapedbeams to observe their effect on the rotation capacity and low-cycle fatigue life of pre-qualified WUF-W connections.

• Journal of the Korea Concrete Institute
• /
• v.27 no.4
• /
• pp.363-375
• /
• 2015

This research investigated the effects of diameter and material of energy frame on the impact velocity or strain rate of Strain Energy Frame Impact Machine (SEFIM). The impact speed of SEFIM have been clearly affected by changing the diameter and material of the energy frame. The reduced diameter of the energy frame clearly increased the impact velocity owing to the higher strain at the moment of coupler breakage. And, titanium alloy energy frame produced the fastest speed of impact among three materials including steel, aluminum and titanium alloys because titanium alloy has faster wave velocity than steel. But, aluminium energy frame was broken during impact tests. In addition, the tensile stress versus strain response of high performance fiber reinforced cementitious composites at higher and wider strain rates between 10 and 72 /sec was successfully obtained by using four different energy frames.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.805-805
• /
• 1995

핵연료저장시설의 화재 등 극단적인 사고조건하에서 $UO_2$ 소결펠렛의 습식산화와 건식산화에 대한 연구를 수행하였다. 손상된 지르칼로이 피복관 속의 $UO_2$ 소결펠렛을 산성분위기의 습윤조건하에서 산화시킬 때의 $UO_2$ 펠렛의 산화속도는 IDR(mg/$\textrm{cm}^2$.min) = 1.55 [H$^{+}$]$^{1.21}$ 로 나타났다. 또한 습윤조건하에서 $UO_2$ 분말에 알카리 및 알카리 토금속 산화물, 그리고 백금족 및 회토류 산화물 등과 같은 불순물들이 존재할 때의 산화속도를 조사하였으며 이들에 대한 영향도 관찰하였다. 핵연료저장시설의 가상화재를 바탕으로 한 400~$700^{\circ}C$의 온도범위에서, 피복관이 씌워진 $UO_2$ 소결펠렛의 건식산화반응을 조사한 바 $UO_2$ 소결펠렛은 산화초기에 U$_4$O$_{9}$ 또는 U$_3$O$_{7}$ 등의 중간상 형성에 따른 3-4%의 부피축소에 의해 결정립계 균열이 일어나고, $600^{\circ}C$ 이하에서는 온도증가에 따라 중간상에서 U$_3$O$_{8}$ 상으로의 상변화에 의한 부피팽창으로 피복관의 변형과 함께 산화속도의 가속을 발견할 수 있었고, $600^{\circ}C$ 이상에서는 핵연료소자의 소성변형으로 인한 산화속도의 지연을 발견할 수 있었다. 또한 $UO_2$ 펠렛의 건식산화거동은 기체-고체 반응시의 전형적인 형태인 shrinking core model에 잘 적용될 것으로 판단되었다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.5
• /
• pp.1-10
• /
• 2022

For Cu-Cr alloy developed for rocket engines, estimated fatigue lives were calculated using various fatigue life prediction methods and compared with fatigue life acquired from low-cycle fatigue tests. The utilized methods for fatigue life prediction are as follows: Coffin-Manson relation, plastic/total strain energy density relations, Smith-Watson-Topper relation, Tomkins relation, and Jahed-Varvani relation. As results of estimation of fatigue lives, it satisfied within scatter band two compared to the test fatigue lives in all methods. The quantitative calculation of the deviation of predicted fatigue lives gives that the total strain energy density relation presents the best result.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.1
• /
• pp.9-13
• /
• 1993

Micro-electronics를 핵으로 하는 기술혁신의 물결이 눈부시고, 우리 주변의 일상생활이 하루가 다르게 변해 가고 있다. Leading-edge technology, high technology, advanced technology 등으로 호칭되는 일군의 새로운 기술의 절대적 level이 현재 어디에 위치해 있는지 확인 조차 하기 어렵고 첨단기술 제품의 성능에 넋을 잃을 지경이 지만 고려청자나 이조백자에 대해서는 현재의 기술을 가지고도 그 재현이 곤란하다. 이와 같이 시차의 이중성 속에서 제품의 부가가치를 높이고 생산성을 올리기 위해서는 가공기술의 고도화를 가하지 않으면 안된다. 어떤 소재를 설계된 모양대로 변화시키는 일련의 과정을 가공이라 한다면 이에는 변형가공(주조, 소성가공), 부가가공(용접), 제거가공(절삭, 연삭)등을 생각할 수 있으며 이들 사이의 가공정도의 개략치는 다음과 같다. (그림.1 가공공정에 따른 가공정도) 공작물에 요구되는 가공정도는 시대의 변천과 더불어 level up되고 이를 위한 기술 개발이 부단히 이어오고 있다. 1960-70 년대의 생산가공 기술은 .mu. m 단위인 $10^{-5}$--$10^{-6}$m의 범위의 가공정도를 생산 line으로 실현하는 것이 중점 개발 목표였다. 그러나, 현재는 $10^{-5}$--$10^{-7}$m를 목표로 한 submicron 가공정도 실용기에 들어서고 있다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.1
• /
• pp.9-16
• /
• 1991

The concept of damage is all-pervasive in structural engineering. It can be considered a state variable and defined to vary from 0(no damage) to 1(failure). Thus, the factor of safety against failure, the most important aspect of a structure, cannot be assessed without evaluating the damageability of a structure under load. It is the objective of the research reported herein to study the behavior of concrete under repeated load applications. Concrete is known to deteriorate under such loading, i.e., it suffers damage of increasing degree. Its response to future loading is a function of the amount of damage sustained during previous load exposures. The same can be said about reinforced concrete members and entire structures, but here we wish to consider only plain concrete and express some of its material properties as functions of the degree of sustained damage. The work described herein is based on the stipulation that the energy dissipation capacity of plain concrete is a material property and the damage accumulates in direct proportion to the degree to which the energy dissipation capacity is being exhausted, in some analogy to both high- and low-cycle failure behavior of materials.

• Journal of the Korea Concrete Institute
• /
• v.16 no.4 s.82
• /
• pp.451-458
• /
• 2004

This study describes the basic concept and the applicability of Hybrid Reinforcement System using conventional steel reinforcing bars and Fiber Reinforced Polymer bars. The concrete bridge decks are assumed to be supported by beams and reinforced with two layers of reinforcing bars. In concrete bridge deck using HRS, the top tensile force for negative moment zone on beam supports is assumed to be resisted by FRP reinforcing bars, and the bottom tensile force for positive moment zone in the middle of hem supports is assumed to be resisted by conventional steel reinforcing bars, respectively. The FRP reinforcing bars are non-corrosive. Thus, the steel reinforcement is as far away as possible from the top surface of the deck and protected from intrusion of corrosive agent. HRS concrete bridge deck has sufficient ductility at ultimate state as the following reasons; 1) FRP bars have lower elastic modulus and higher ultimate strain than steel re-bars have, 2) FRP bars have lower ultimate strain if provided higher reinforcement ratio, 3) ultimate strain of FRP bars can be reduced if FRP bars are unbonded. Test results showed that FRP and HRS concrete slabs are not failed by FRP bar rupture, but failed by concrete compression in the range of ordinary reinforcement ratio. Therefore, in continuous concrete bridge deck using HRS, steel reinforcing bars for positive moment yield and form plastic hinge first and compressive concrete fail in the bottom of supports or in the top of the middle of supports last. Thus, bridge deck consumes significant inelastic strain energy before its failure.