• Applied Chemistry for Engineering
• /
• v.9 no.7
• /
• pp.1011-1017
• /
• 1998

$YBa_2Cu_3O_{6+x}(Y123)-Ag$ high-Tc superconducting wires were fabricated by plastic extrusion technique using pyrophoric synthetic and mechanical mixing powder with and without Ag addition(20 wt.%). This method involves powder preparation, plastic paste making, die extrusion, binder burn-out and the sintering process. In order to fabricate a good-quality superconducting body, it is required to use homogeneous and fine-size power as a starting materials. $Y_2O_3-BaCO_3-CuO$ precursor powders with/without Ag addition were prepared both by pyrophoric synthetic(PS) and mechanical mixing(MM) method of raw powders. The formation kinetics of the powder mixtures into Y123 phase was investigated at various temperatures and times in air atmosphere. The powder prepared by PS method was more easily converted into a Y123 phase than the MM powder. The fine size and good chemical homogeneity of the powder prepared by PS method is attributable to the fast formation into a Y123 phase. The critical current density($J_c$) of the Y123-Ag superconducting wires made by plastic extrusion method were in the range of $150A/cm^2{\sim}230A/cm^2$. depending on the charateristics of starting material powders. $J_c$ of the wire prepared by pyrophoric synthetic powder with 20 wt.% Ag addition was $230A/cm^2$.

• Journal of the Korean Ceramic Society
• /
• v.41 no.4
• /
• pp.284-288
• /
• 2004

To improve mechanical properties of $Al_2$O$_3$/ZrO$_2$composites have been controlled dispersion of ultra low size ZrO$_2$ particles in $Al_2$O$_3$ ceramics by polymeric precursor method (Pechini process). In case of coprecipitation or mechanical mixing of ZrO$_2$ powders with $Al_2$O$_3$, homogeneous dispersion and controlling the ZrO$_2$ size were relatively difficult due to high sintering temperature. So the polyesterization process of Zr/Y(NO$_3$)$_3$-citric acid solution in ethylene glycol with the commercial sub-micron sized o(-alumina powder (Sumitomo AES-11(0.4 ${\mu}{\textrm}{m}$)) was adopted in order to obtain homogeneous dispersion of ZrO$_2$ in A1203. By this partial polyesterization process, the homogeneous dispersion of relatively low sized ZrO$_2$in $Al_2$O$_3$/ZrO$_2$composites was achieved at 1450∼1$600^{\circ}C$ of sintering temperature range and their mechanical properties were measured.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.5
• /
• pp.235-242
• /
• 2017

In order to prepare porous scaffolds capable of pore control, PMMA powder serving as a pore-forming agent was added to HA powder to synthesize a slurry containing TBA as a solvent. And then, porous HA scaffolds where pillarshaped pore channels interconnected with each other were fabricated by freeze-casting and sintering. The crystal structure of the HA scaffolds according to the addition amount of PMMA powder was measured by XRD and the surface and inner cross section of the scaffolds were analyzed through SEM. It was found that removal of PMMA during sintering affects the internal structure of the scaffolds and the crystallinity of the HA powder. Furthermore, through evaluating the physical and mechanical properties of the scaffolds, it was confirmed that the porosity, pore size and compressive strength can be controlled by controlling the addition amount of the pore-forming agent. It was also found that the HA scaffolds produced in this study were similar in structure and properties to the natural cancellous bone. This suggests that porous HA scaffolds with PMMA can be used as an alternative to autogenous bone for tissue engineering as an artificial bone scaffold.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.10
• /
• pp.51-59
• /
• 1998

($Na_{1/2}Ln_{1/2}$)$TiO_3$ceramics have a high relative dielectric constant and a positive temperature coefficient of resonant frequency ($\tau_f$)(where Ln represents a lanthanide: $La^{+3}$, $Pr^{+3}$, $Nd^{+3}$ and $Sm^{+3}$). On the other hand, $MgTiO_3$ ceramic has a high Qf value and a negative temperature coefficient. So We have investigated the microwave dielectric properties of $xMgTiO_3$-(1-x) ($Na_{1/2}Ln_{1/2}$)$TiO_3$. In these systems, there are no clues on solid-solution and secondary phase. There are mixed phases with $MgTiO_3$and ($Na_{1/2}Ln_{1/2}$)$TiO_3$ phases. Its dielectric characteristics (Qf, temperature coefficient and dielectric constant) are intermediate between ($Na_{1/2}Ln_{1/2}$)$TiO_3$ and $MgTiO_3$ and are predictable by the logarithmic mixing rule. The dielectric ceramic compositions temperature coefficient each approximates to zero at Ln=La, x=0.9, Ln=Pr, x=0.87, and Ln=Nd, x=0.84. At this time, there are Qf values in the range of 55,000 to 28,00GHz and relative dielectric constants in the range of 22 to 25.

• Resources Recycling
• /
• v.8 no.4
• /
• pp.45-56
• /
• 1999

The purpose of tlus sludy was to preparc raw material powder for Mn-Zn iclrile, h m mined mill scale and fero-Mn, usins a co-spray roasting process The mill scale and ferra-Mn uscd in this raalins process was rcf~nedb y mesn-ns of a slxc~apl rxcss ~nvolvinm~a te~ialsc ontalning imp~u-ltleso r less than 100 pprn In this study an effeclive spray roaster system. wllich produces fme complex oxide powder, collects produccd ~owder.,m d prcvel~tse ~~llssiooifi HCI gas. was also manufactured. By means of spray~ngp urifcd raw malerial solu~lionl nln a manufacued high tcmpervture rumace. &-ferrite powder and a comnpleu o ~ d e powder of Fe,O; and M,x203 were manufactured. The chmcterlstics of the composllion. surface urca, and p'miicle size dismbulion or the produced powder were exmined. ptoduced powdcr was then ~ m e dwi tli ZnO powder. aid olher addilives of defined cornposnion, and Mn-Zn femite cares werc praiuccil by meuns of Sorlning and closely controlled sintering processes. The magpelic p~oprlieso f c olo~ss, initlal permeability. mauin~u~mnn agnehc flux. coz~civcr orcc and residual magnccic flux for the above cores we,= measured, and fmm Il~ase I-csulls the eflicacy of lhe co-spray roasling pncess to pl.ellare raw material powder lor Mn-Zn ferntc was established

• Korean Journal of Materials Research
• /
• v.11 no.3
• /
• pp.178-184
• /
• 2001

Transparent and highly oriented KLN thin films have been grown by an rf- magnetron sputtering deposition method. A homogeneous and stable KLN target was prepared by calcine and sintering process. For KLN target, stoichiometry and composition excess with K of 30% and 60%, and Li of 15% and 30% respectively, was prepared. The targets were sintered at low temperature to prevent vaporization of K and Li. KLN thin films were fabricated by rf-magnetron sputtering method using those targets. In this experiment, using the target of composition excessed with K of 60% and Li of 30%, single phase KLN thin film was produced. KLN thin film has excellent crystallinity and highly c-axis oriented on Corning 1737 substrate. Transmittance of thin film in visible range was 90%, absorption edge is 333 nm and refractive index at 632.8 nm was 1.93.

• Journal of the Korean Ceramic Society
• /
• v.39 no.4
• /
• pp.359-366
• /
• 2002

The purpose of this study is to investigate the properties of LSGM electrolyte and LSM cathode. The unit cell based on the optimum conditions and processing for high performance was fabricated and measured. The single phase of $LaGaO_3$ was obtained on sintering at $1500^{\circ}$ for 6h with composition of $(La_{0.85}Sr_{0.15})(Ga_{0.8}Mg_{0.2})O_{3-\delta}와 (La_{0.8}Sr_{0.2})(Ga_{0.8}Mg_{0.2})O_{3-\delta}$ and $(La_{0.85}Sr_{0.15})(Ga_{0.8}Mg_{0.2})O_{3-\delta}$. The grain size of the sintered body was about $10∼30{\mu}m$ and electrical conductivity was 0.13 S/cm measured at $800^{\circ}$. The single phase of $LaMnO_3$ structure in $(La1-xSrx)MnO_3$ system was obtained at x=0∼0.2 and the particle size of the synthesized powder was about 40 nm. The unit cell was prepared by firing at $1200^{\circ}$ for 1h with $(La_{0.9}Sr_{0.1})MnO_3$ cathode and 0.9NiO-0.1YSZ anode screen-printed on surfaces of $(La_{0.8}Sr_{0.2})(Ga_{0.8}Mg_{0.2})O_{3-\delta}$ electrolyte. The grain size of the electrode was close to $1{\mu}m$ and the electrode had porous structure. The maximum power density of unit cell showed $0.3W/cm^2$ at $800^{\circ}$.

• Applied Chemistry for Engineering
• /
• v.32 no.4
• /
• pp.409-416
• /
• 2021

Dimensionally stable electrodes are one of the important components in electrochemical water treatment processes. In the manufacturing of the dimensionally stable electrodes, the type of metal catalyst coated on the surface of the metal substrate, the coating and sintering methods substantially influence their performance and durability. In this study, using Ir-Ru-Ta ternary metal coating, various electrodes were prepared depending on the coating method under the same pre-treatment and sintering conditions, and its performance and durability were studied. As a coating method, brush and spray coating were used. As a result, the reduction in the amount of catalyst ink was achieved because more amount of metal could be coated for the electrode using spraying with the same amount of catalyst ink. In addition, the spray_2.0_3.0 electrode prepared by a specific spray coating method shows the phenomenon of cracking and the uniform coating of the ternary metal on the surface of the coating layer, and results in a high electrochemically active specific surface area, and the decomposition performance of 4-chlorophenol was superior to the other electrodes. However, it was found that there was no significant difference in durability depending on the coating method.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.30 no.1
• /
• pp.16-22
• /
• 2014

Purpose: The purpose of this study was to assess the marginal and mesial fitness of zirconia single copings and 3-unit fixed partial dentures (FPDs) manufactured with an identical model. Materials and Methods: An epoxy model in which the maxillary right 2nd premolar is lost and maxillary 1st premolar and 2nd molar are formed as abutments was manufactured and scanned by using a laser scanner. A ten units of zirconia single copings were manufactured for maxillary 1st premolar and 2nd molar, respectively and the same number of 3-unit FPDs were manufactured. For the measurements of fitness, the manufactured silicone replicas were divided into four parts and the fitness were measured by digital microscope at measurement points (P1, P2, P3, P4 and P5) of each plane. The measured gaps were classified into three categories: marginal gap (MG, P1), axial gap (AG, average of P2 and P3), occlusal gap (OG, average of P4 and P5). Results: The ranges of MG, AG and OG for single copings were 18.47 - 40.54 ${\mu}m$, 39.73 - 73.61 ${\mu}m$ and 116.90 - 134.69 ${\mu}m$, respectively. The ranges of MG, AG and OG for 3-unit FPDs were 45.95 - 87.44 ${\mu}m$, 23.78 - 57.00 ${\mu}m$ and 99.89 - 131.06 ${\mu}m$, respectively. Conclusion: The result of the study shows that the MGs for 3-unit FPDs were higher than those of single copings, though they are within the range of clinical acceptance, indicating that the use of more homogeneous zirconia block and modification of sintering processes are needed to ensure the prevention of increase of gap in 3-unit FPDs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.83-83
• /
• 2009

우수한 압전성을 가지는 PZT는 인체에 유해한 다량의 PbO을 함유하여 심각한 환경문제를 야기함은 물론 제조 공정 중 PbO 휘발 억제 시설 구비에 따른 경제적 부담 등 문제점이 지적되었다. 따라서 환경오염 및 가격경쟁력을 갖추기 위해 현재 무연 조성 세라믹스에 대한 많은 연구가 진행되고 있다. 최근 비납계 압전 세라믹의 연구는 비스무스 레이어형과 페로브스카이트 형 비납계 세라믹스의 연구가 활발히 진행되고 있다. 특히 $(Na,K)NbO_3$ 계는 페로브스카이트 구조를 가지는 비납계 세라믹으로 현재 많은 연구가 진행되고 있다. 이 물질은 PZT계와 유사하게 상전이(morphotropic phase boundary:MPB)영역을 가지고 있 으며 이 영역에서 높은 압전 특성을 보여주고 있다. 최근 $Na_{0.5}K_{0.5}NbO_3$에 $LiTaO_3$를 치환하여 우수한 압전 특성을 지니는 조성이 개발되고 있지만, 보통 소성법으로 제조된 세라믹스는 PZT계 세라믹스와 비교하여 특성이 떨어진다. 본 연구에서는 압전성이 우수한 $(Na_{0.44}K_{0.52}Li_{0.44})(Nb_{0.90}Sb_{0.06}Ta_{0.04})O_3$ 조성에 도너 도핑과 억셉터 도핑을 한 다음 전기기계결합계수, 압전상수, 유전상수의 변화를 평가하고, hardener 와 softener 특성이 본조성에서 나타나는지를 관찰하였다. 실험방법은 보통 소성법을 사용하였으며, 분쇄와 혼합은 직경 3 mm zirconia ball을 사용하여 볼밀 하였다. $850^{\circ}C$ 에서 5h 하소 후 $1100{\sim}1200^{\circ}C$ 에서 소결하고, 두께 1 mm로 연마한 다음 silver paste를 $650^{\circ}C$ 에서 소부하여 전극을 형성하였다. 제작된 시편은 $90^{\circ}C$의 실리콘유에서 3~4 kV/mm의 전계를 가해 20분간 분극 처리를 수행하였다. 제작된 시편의 압전전하 상수 값은 d33-meter(APC-8000)를 이용하여 측정하였고, 유전율, 전기기계결합계수 및 기계적품질계수 등은 임피던스 분석기 (impedance/gain phase analyzer)를 이용하여 특성을 측정 하였다. 또한 전압-분극 특성의 평가에는 강유전특성 측정기(ferroelectric tester: Precision-LC, Radiant Technologies, USA)를 이용하였다.