• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.501-504
• /
• 2014

자동차의 하중을 지탱하고 자동차의 방향 전환 유지와 노면 충격을 흡수 완화하며, 엔진의 구동력과 브레이크 작동 시 제동력을 노면에 전달하는 등의 기능을 수행하는 타이어의 상태는 안전과 직결되어 있다고 볼 수 있다. 주행 중 타이어의 불량으로 인한 사고는 무시할 수 없는 부분을 차지한다. 타이어의 편마모는 주행 안전성을 위한 타이어의 문제 중 하나로 운전자의 운전습관과 휠얼라이먼트의 이상 등으로 타이어의 특정 부위가 마모되는 증상을 말하는데, 객관적으로 정확하게 검증할 수 있는 측정방법이 없는 것이 현실이다. 본 논문에서는 현실의 주관적인 검증기준의 단점을 보완하고 키넥트 센서를 이용하여 각 타이어의 마모 정도를 체크하여 편마모를 객관적으로 검증할 수 있는 시스템을 설계하고자 한다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.51-56
• /
• 2016

In this paper, we propose an Arduino-based plant monitoring system. The proposed system is based on the Arduino platform, using an environmental sensor and a pressure sensor for measuring temperature, humidity and illuminance in order to monitor the state of the environment and the facilities of the plant. Monitoring data are transmitted to a ZigBee coordinator connected to a server through a radio frequency transceiver. When using a pressure sensor and the environment sensor data stored on the host server, checking the pressure in the environment of the plant and equipment is intended to report any alarm status to the administrator. Using a grid line-based key distribution scheme, the authentication node dynamically generates a data key to protect the monitoring information. Applying a ZigBee wireless sensor network does not require additional wiring for the actual implementation of a plant monitoring system. Possible working-environment monitoring of an efficient plant can help analyze the cause of any failure by backtracking the working environment when a failure occurs. In addition, it is easy to expand or add a sensor function using the Arduino platform and an expansion board.

• Journal of IKEEE
• /
• v.26 no.2
• /
• pp.219-225
• /
• 2022

The textile industry in Korea, the dyeing sector is an energy-intensive sector and has low per-unit productivity due to its labor-intensive nature. If the defective rate of dyed fabrics is high, additional costs are incurred due to an increase in production cost due to re-dyeing. Therefore, the goal of the dyeing factory was to minimize the defect rate rather than to save energy. It was difficult to check the dyeing state of the fabric in real time due to the risk of accidents due to burns or pressure when dyeing in a high-temperature and high-pressure environment. In this paper, a complex sensor that can measure the exhaustion rate of dye solution in the dyeing machine using turbidity, pH, and conductivity sensors was proposed, and the experimental method and experimental results were analyzed.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.525-526
• /
• 2016

전기자동차 (EV)에서 구동용 모터의 토크 제어를 위한 인버터에는 제어 연산 및 고장 진단 기능을 수행하기 위한 MCU가 있으며, MCU는 상위 제어기 차량 제어 유닛 (VCU)에게 현재 모터 및 인버터의 상태를 주기적으로 전달하고, 현재 차량 주행에 적합한 토크 지령을 받아 토크 제어를 수행하게 된다. 이를 위해 MCU는 전류, 전압 및 위치 센서의 값을 읽어 제어를 수행하게 되며, 제어의 결과 값으로 pulse width modulation (PWM)을 생성하여 이를 통해 모터에 전압을 공급하게 된다. 즉 차량의 구동에 있어 PWM 신호는 가장 중요한 부분이다. 하지만 생산 불량 또는 진동에 의한 납땜 불량 또는 MCU 전원 고장 등으로 MCU에 고장이 발생하게 되면 이상 PWM을 생성하게 되고 정상적인 토크 제어가 불가능해진다. 이때 안전하게 EV를 정지 시키는 알고리즘이 필요하게 되며, 이를 수행 할 supervisor control unit (SCU)가 인버터 컨트롤 보드에 추가되어야 한다. 본 논문에서는 고속으로 주행하던 차량에서 메인 MCU가 고장 날 경우에 안전하게 EV를 정차시키는 방법에 대해 다루었다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.7
• /
• pp.1634-1640
• /
• 2010

In this paper, I studied the "Establishment of Fault Tolerant System" as well as the sensor and cylinder that are general components being used in automation equipments. I design a system that when the sensor breaks down on free flow conveyor, it will be converted to virtual sensor system mode by simulation, also I design IPC(Internal Pressure Cylinder), a basis of various applicable fault tolerant system by analyzing the changing of analog data according to the load of operation. With IPC and the increasing ability of developer, the Fault Tolerant System will be widely applied in the increasment of service time of cylinder, grease pouring time expection, fault recognition of cylinder and etc.

• Journal of IKEEE
• /
• v.18 no.1
• /
• pp.77-95
• /
• 2014

In general, image acquisition characteristics tests of image sensors and modules vary widely according to the characteristics of image sensors and modules under test, the application purpose of target devices where image sensors and modules are mounted, and the functions of test equipments. However, some de facto standard tests are frequently used in industry fields. They differ only in several parameters e.g. thresholds for fault detection, and they can be applied to most image sensors and modules. In this paper, 11 typical tests are explained in detail, and they are described in a simple and clear form under single framework, which significantly reduces errors and saves efforts.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.151-156
• /
• 2013

The experiment was done on cars travelling at the speeds of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. In this experiment, the relativity between the secondary waveform coming from ignition coil and exhaust emissions were measured in case of cars with failures, in oxygen sensor, spark plugs. The following results obtained by analysis of the relativity between the secondary waveform and exhaust emissions. 1) When the oxygen sensor is failure, the average value of CO emission measured was 6.8 times higher than the standard CO emission value and the average value of HC emission measured was 2.3 times higher than the standard emission level. 2) When engine parts are in failure, more fuel enters the cylinder due to longer opening duration of injector, and it tended to make CO and HC emission values increase. 3) Combustion duration, the shape of flame propagation during spark line, and the size of the discharge-induced energy were the three main elements that directly cause variations in CO and HC emission values.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.3
• /
• pp.128-133
• /
• 2021

Recently Recently, the incidence of spinal diseases due to poor posture among students and office workers is increasing, and various studies have been conducted to help maintain correct posture. In previous studies, a membrane sensor or a pressure sensor was placed on the seat cushion to see the weight bias, or a sensor that restrained the user was attached to measure the position change. In our previous study, we developed a sensor device which can be easily attached to the body with an adhesive gel sheet and that measures and outputs the user's posture and body position in real time, but it has a limitation in the accuracy of the sensor value. In this study, a study was conducted to improve the performance of the position conversion sensor device and quantitatively evaluate the accuracy of the angle conversion measurement value, and a high accuracy with 2.53% of error rate was confirmed. In future research, it is considered that additional research targeting actual users is needed by diversifying posture correction training contents with multimedia elements added.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1992.04b
• /
• pp.29-38
• /
• 1992

무인화된 대량생산 체제에서는 transfer line을 이용하게되며, cycle time의 단축을 위하여 측정 및 검사기능이 별도의 station으로 있어 가공후에 부품의 불량여부를 감지한다. 그러나 다품종소량생산체제에서는 FMC 또는 FMS가 적합하며, 이 시스템에 바람직한 감시기능으로서는 기내측정(inter-process)방식을 많이 이용한다. 여기서는 CNC선반과 머시닝센터에 접촉식 센서인 터치프로브(touch probe)를 설치하여 개발한 무인 FMC용 인터프로세스 3차원 측정 및 검사시스템을 소개한다.

• 기계와재료
• /
• v.22 no.1
• /
• pp.66-75
• /
• 2010

곡물선별기는 호퍼, 진동식 정량시료공급장치, 공급벨트 또는 슈트, 램프, 이미지 센서, 공기총, 제어장치로 이루어져 있고, 농산물 등의 제품속의 이물질이나 불량품을 선별해내는 장치로 최근의 국내외 식생활의 향상과 더불어 매우 부가가치가 높은 제품으로 평가받고 있다. 본고에서는 곡물선별기의 국내외 최신동향을 다루었으며, 곡물선별기에 있어 핵심부품인 이젝터 및 이젝터용 밸브를 집중적으로 조명하였다. 특히 솔레노이드 밸브를 대신하는 압전식 밸브의 타당성을 논하기 위하여 압전 액추에이터 설계/제작/실험결과 관련 정보를 수록하였다.