• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.275-276
• /
• 2008

통신기기가 고주파수화 함에 따라서 저유전 저손실 재료의 필요성이 증대되고 있으며, 세라믹/폴리머 복합재료를 고주파 회로 기판 소재로 이용하려는 관심이 증폭되고 있다. 본 연구에서는 저손실, 저유전율 특성을 구현하기 위해 $SiO_2$를 세라믹 필러로 복합물을 제작하였다. 평균 입자 크기가 16nm, $2.3{\mu}m$의 fumed 실리카와 평균 입자 크기 $1{\mu}m$, $4{\mu}m$의 fused 실리카를 사용하였다. 이 4종류 실리카를 사용하여 slurry를 제작하고 이를 활용하여 tape을 제작하였다. 제작된 복합체 tape을 적층하여 기판을 제작해 기판의 유전특성을 측정하였다. fumed 실리카의 경우 $SiO_2$ 10vol%이상에서는 균일한 tape성형이 어려워졌으며, 유전 손실이 fused 실리카와 비교하였을 때 큰 폭으로 증가하였다. fumed silica, fused silica 두 종류 모두 입도가 증가하면 유전손실이 증가하였다.

• Electrical & Electronic Materials
• /
• v.6 no.3
• /
• pp.241-247
• /
• 1993

본 연구에서는 투광성 0.085Ba(L $a_{1}$2/N $b_{1}$2/) $O_{3}$- 0.915Pb(Z $r_{y}$ $Ti_{1-y}$) $O_{3}$(0.45.leq.y.leq.0.70)세라믹을 2단 소성법으로 제작한 후, PbZr $O_{3}$조성 및 온도에 따른 구조적, 강유전적특성을 측정하였다. XRD측정 결과, PbZr $O_{3}$조성이 감소할수록 결자상수 및 단위격자 체적은 감소하였으며 시편의 결정구조는 입방정계에서 능면체정계, 정방정계로 변화되었다. 8.5/60/40시편의 경우 포화분극, 잔류분극 및 항전계가 각각 33.28[.mu.C/$cm^{2}$], 4.15[kV/cm]로 전형적인 메모리 특성을 나타내었으며 PbZr $O_{3}$조성이 증가함에 따라 강유전 이력곡선은 slim loop특성을 나타내었다. 잔류분극은 온도가 증가함에 따라 감소하였으며 특히 PE-FE상경계 부근에 위치한 조성의 경우, 상전이 온도 이하의 온도에서 급격히 감소하는 경향을 나타내었다.다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.331-332
• /
• 2006

Ag-ceramic composite materials were investigated as internal electrodes for multilayer ceramic actuators (MLCA). Ag-ceramic pastes were prepared by adding PZT-based ceramic powders to a Ag patse in a range of 0 to 50 wt.%. PZT/Ag-PZT multilayered laminates were fabricated by tape casting and fired at low temperatures below $950^{\circ}C$. The addition of ceramic into the Ag electrode resulted in a decrease in the thermal expansion mismatch between the electrode and the ceramic sheet. The maximum strain of PZT/Ag-PZT multilayered actuators were $9{\times}10^{-4}$ under an electric field of 2.5MV/m. In conclusion, Ag-PZT composite materials are efficient for low cost piezoelectric MLCAs.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.1
• /
• pp.12-18
• /
• 2019

The spherical $SiO_2$ powders were synthesized by the scaled-up ultrasonic pyrolysis (USP). The aqueous $SiO_2$ sol, which contained 20~30 nm $SiO_2$ particles, was used as a precursor for the scaled-up USP. The effects of the USP operating conditions and precursor conditions were systematically investigated, including reaction temperature, gas flow rate, and the concentration of $SiO_2$ sol on the morphologies of synthesized $SiO_2$ particles. the synthesized $SiO_2$ particle showed a pseudo-crystal phase, spherical morphology, and a smooth surface. The size of the spherical $SiO_2$ particle decreased as both reaction temperature increased and precursor concentration decreased. In addition, the synthesized $SiO_2$ particle size was increased by increasing the gas flow rate. Lastly, the scaled-up USP was compared with the lab-scale USP based on the same process conditions. Due to a short retention time in the reaction tube during the USP process, the $SiO_2$ particle synthesized via the lab-scale USP showed a larger particle size.

• Progress in Superconductivity and Cryogenics
• /
• v.25 no.2
• /
• pp.10-13
• /
• 2023

High-T_C superconductivity (HTSC) has been the central issue in the field of condensed matter physics for decades. An essential part of the research on superconductivity is finding new exotic superconductors. It was recently suggested that Ir-substituted La_0.7Sr_0.3MnO₃ (LSMIO) is a new high-T_C superconductor. However, systematic studies to experimentally verify the superconductivity have not been done. Here, we report the growth processes of LSMIO thin films and their electrical transport properties. We observed a clear negative correlation between the intensity of the laser utilized for film deposition and the Curie temperature of the deposited film. We attributed this effect to the suppression of Sr concentration in the LSMIO films as the laser intensity increased. However, our LSMIO films show conventional ferromagnetism instead of HTSC. To realize the HTSC in LSMIO systems, further exploration of diverse compositions of LSMIO compounds is essential.

• Membrane Journal
• /
• v.33 no.6
• /
• pp.439-446
• /
• 2023

Ceramic membranes are generally used for various industrial processes operating under extreme conditions because of its high thermal and chemical stability. However, due to the trade-off phenomenon of permeability and mechanical strength, preparation of high permeability-high strength membrane is necessary. In this study, the change in characteristics and performances of ceramic membranes was analyzed depending on the type of polymer binder and its mixing ratio. Because the solubility between solvent and polymer binder was higher in PSf (polysulfone) than in PES (polyethersulfone), the viscosity and discharge pressure of the PSf-based dope solution were higher than those of PES-based dope solution. When PSf was used as a polymer binder, ceramic membrane showed high mechanical strength and low water permeability due to the dense structure. On the other hand, in case of PES, the mechanical strength was slightly reduced and the water permeability was increased. It was confirmed that the optimum mixing ratio of the PSf and PES with high water permeability and mechanical strength was 9:1.

• Ceramist
• /
• v.23 no.1
• /
• pp.89-100
• /
• 2020

Abnormally large electromechanical strain properties have been reported in bismuth-based piezoelectric ceramics, which cast a promise for replacing the market-dominating PZT-based piezoelectric ceramics in actuator applications. In spite of these large strains in bismuth-based piezoelectric ceramics, there still remains a critical issue for its safe transfer to practical applications, representatively, a relatively high operating field required to obtain the large strain properties. To overcome the challenge, much attention has been paid to so-called 0-3(or 3-0) type ceramic/ceramic composite approach to better tailoring the strain properties of bismuth-based piezoelectric ceramics. The approach turns out to be highly effective, leading to a drastic decrease in the operating electric field for these materials. Besides, both extensive and intensive search for the related mechanism revealed that the reduction in the operating electric field is largely due to the contribution from polarization coupling or strain coupling model between two different ceramics. This article reviews the status of the art in the development of novel ceramic/ceramic composites to make large incipient piezostrains in bismuth-based lead-free piezoelectric ceramics practical.

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.231-242
• /
• 2014

An interconnect in solid oxide fuel cells (SOFCs) electrically connects unit cells and separates fuel from oxidant in the adjoining cells. The interconnects can be divided broadly into two categories - ceramic and metallic interconnects. A thin and gastight ceramic layer is deposited onto a porous support, and metallic interconnects are coated with conductive ceramics to improve their surface stability. This paper provides a short review on ceramic materials for SOFC interconnects. After a brief discussion of the key requirements for interconnects, the article describes basic aspects of chromites and titanates with a perovskite structure for ceramic interconnects, followed by the introduction of dual-layer interconnects. Then, the paper presents protective coatings based on spinel-or perovskite-type oxides on metallic interconnects, which are capable of mitigating oxide scale growth and inhibiting Cr evaporation.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2003.11a
• /
• pp.146-148
• /
• 2003

Bayer 공정은 가성소다를 이용하여 보오크사이트로부터 수산화알루미늄을 추출하는 공정이다. 그러나 보오크사이트 추출 후 1차 침전공정에서 반응한 보오크사이트 잔사는 침전시킴으로써 깨끗한 공정액을 분리하는 데 이때 침전되지 못한 다량의 분산성 고형물이 공정액 중에 존재하게 되는데 이를 분산성 보오크사이트(레드머드) 미립자라하며 보통 80-100mg/$\ell$의 농도를 나타낸다. 그러므로 이를 제거하기 위해 다음 공정인 입상여과필터 공정을 사용하는데 이때 필터링 효율증대를 위해 보조제로써 다량의 소석회(Ca(OH)$_2$)를 투여하여 공정액 중의 고형물을 농도를 8-100mg/$\ell$에서 5mg/$\ell$로 낮추는 공정을 사용하고 있다. 특히 국내 수산화알루미능 제조회사일 KC(주)의 경우 소석회 사용량이 일 10톤, 년간 약 3,600톤을 사용함으로써 소석회의 사용량에 따라 같은 량의 슬러지가 발생되게 된다. 따라서 여과후 발생되는 슬러지의 처리비용 문제(연간 9천만원)와 소석회의 미립자에 의한 공정액의 2차 오염과 제품 품질 저하(quality claim) 및 소석회 사용량에 따른 연간 원료비(연간 3억원) 등의 상당한 문제점을 나타내고 있는 실정이다. 아울러 최근 고품위 수산화알루미늄의 공급 요구에 따라 여과시 정제기준이 점차 낮아져 이제는 1mg/$\ell$ 이하를 유지하여야 하는 근본적인 문제에 봉착해있는 실정이다. 그러므로 본 연구에서는 소석회를 사용하는 입상여과법을 대체하기 위한 신공정개발을 추진하였으며, 그동안 카트리지여과법 등의 다양한 실험 결과로부터 최근 필터 보조제를 첨가하지 않는 물리적 여과방법인 세라믹 막 여과법의 적용 가능성을 확인하고 친환경공정인 세라믹 막 여과 실용화 공정 기술을 개발하였다. 세라믹 막 여과 법은 여과 보조제를 사용하지 않으므로 2차적인 슬러지 발생등의 환경문제를 발생하지 않으며, 공정액에 첨가제를 투입하지 않으므로 순환형 친환경공정으로 각광받을 수 있다. 본 연구에서는 고온, 고농도의 NaOH 수용액의 처리에 적합한 막소재와 발생될 수 있는 제반 문제점 등을 파악하였고, 장기간의 실험을 거쳐 최적 투과 압력(Trans membrane pressue), 세정 조건 및 주기, 막재질에 있어서 보강하여야 할 Point, 최적 운전 조건들을 토출해 내었고, 향후 실제 Plant에 적용할 계획이다.

• Journal of Navigation and Port Research
• /
• v.27 no.1
• /
• pp.75-80
• /
• 2003

The electromagnetic wave absorption ability of natural ceramics(NC), natural lacquer, and rubber was investigated. The natural ceramics showed absorption ability above 2.5dB at 2.5GHz~4.5GHz and natural lacquer showed better electromagnetic wave absorption ability than that of rubber. The simulation results of electromagnetic wave absorber ability in a absorber composed of natural lacquer and ferrite showed the reflection coefficient of -16dB at 0.5GHz~10GHz. It was shown that from the simulation results, the electromagnetic wave absorber composed of lacquer as a backing material have better absorption ability than that of the electromagnetic absorber composed of rubber.