• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.06a
• /
• pp.34-35
• /
• 2003

고에너지적 Nd-Fe-B계 소결자석 제조를 위한 펄스자장 성형시, 금형 및 다양한 성형조건이 자석의 이방화율 향상에 미치는 영향에 대하여 조사하였다. 일반적으로 butterfly, disk or coin 형태의 자석을 제조하는 방법으로는, 종축자장성형법(Axial Die Press, ADP)을 이용하여 최종제품의 near-net shape으로 성형 및 소결하는 방법과, 횡축자장성형법(Transverse Die Press, TDP)을 이용하여 blick or cylinder 형태로 제조한 후 여러 단계의 가공공정을 거쳐 최종제품으로 제조하는 방법이 적용되고 있다. 그러나, ADP의 경우 분말의 자장정렬 후 성형단계에서 성형밀도가 증가함에 따라 배향의 틀어짐 현상이 증가하므로 이방화율 향상의 한계가 있어 (BH)$_{MAX}$+iHc=54 이상의 자석은 제조되기 어렵고, TDP의 경우 고이방화 자석의 제조가 가능하나 복잡한 형상의 제품을 직접 성형할 수 없어 성형/소결 후 복잡한 가공공정을 거쳐야 하므로 재료의 손실뿐만 아니라 고가의 가공비용이 소요되므로 경제적인 문제점을 갖게 된다. 반면에, 펄스자장 종축성형방법(PDP)은 3T~5T의 펄스자장을 이용하여 분말의 정렬 및 성형을 동시에 수행함으로써 TDP보다 향상된 배향율이 얻어질 수 있으며, ADP으로만 실현 가능한 복잡한 형성의 자석을 near-net shape으로 제조가 가능한 잇점이 있다.다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.279-280
• /
• 2007

In this study, it is investigated that the effect of material properties such as various temperature, forming speed and strain rates on formability and forming limits of Mg alloy sheet in square cup deep drawing. Since the sheet metal forming of Mg alloy is perform at elevated temperature, the effect of strain rates related with the forming temperature and forming speed is very important factor for formability and forming limits. Therefore, the investigation for process variables is necessary to improve formability and forming limits. Also, the effects of strain rate and thickness transformation were studied by the experimental and FE analysis using the square cup deep drawing. The temperature, forming speed, and strain rates were investigated. Forming of Mg alloy takes consider into temperature, proper forming speed and strain-rate the formed parts were good without defects fur forming limits.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.240-243
• /
• 1995

This paper describes the process design and forming limit of the forged hinge produec with the axial protrusion on the sheet metal. Process design is consisted of preform and forging process. In this case, the forged hinge product can be formed in a single workpiece without assembling another axial part to it. Process design of the forged hinge product is analyzed by the commercial FEM program. It is known that process design with perform process, shown by the FEM simulaion, can bring the forming limit of the forged hinge product to a great expansion.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.144-149
• /
• 2014

Large residual stresses are remained in the conventional injection molded products because of the high cavity pressure in packing phase during injection molding process. Conventional injection molding (CIM) invokes distribution of cavity pressure and it has a limitation to obtain product with uniform physical property. Multi-cavity conventional injection molding contains quality deviation among the cavities since flow imbalance occurs during filling phase. Injection compression molding (ICM) is adopted to overcome these limitations of CIM. In this study, molding characteristics of CIM and ICM have been investigated using multi-cavity injection mold. Researches were performed by both experiment and computer simulation through observations of birefringence for transparent resins, polycarbonate and polystyrene in CIM and ICM. As a result, low and uniform birefringence and mold shrinkage were showed in the specimens by ICM that could give a uniform cavity pressure. Deviation of physical property among the specimens in multi-cavity mold shown in CIM was significantly reduced in the specimens by ICM. Through this study it was concluded that the ICM in multi-cavity molding was valid for molding products with uniform property in an individual cavity and also reduced property deviation among the cavities.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.289-293
• /
• 2007

The effect of temperature on the forming limit diagram was investigated for AZ31B magnesium alloy sheet through the limit dome height test in the range from room temperature to $300^{\circ}C$. The formability of AZ31B sheet was improved significantly according to the increasing temperature. Also we studied the springback characteristics through the 2D draw bending test with different blank holding forces at elevated temperatures. Springback quantity was considerably reduced as temperature went up. The blank holding force in the range used, however, had little influence on springback. Experimental results obtained in this study may provide a material database for AZ31B sheet.

• Journal of Industrial Technology
• /
• v.30 no.A
• /
• pp.49-57
• /
• 2010

A forming limit diagram (FLD) defines the extent to which specific sheet material can be deformed by drawing, stretching or any combination of those two. To determine the forming limit curve (FLC) accurately, it is necessary to perform the tests under well-organized conditions. In this study, the influence of several geometric or process parameters such as the blank shape and dimensions, strain measuring equipments, test termination time, forming speed and lubricants on the FLC is investigated.

• The Academic Congress of Korean Shoulder and Elbow Society
• /
• 2009.03a
• /
• pp.187-187
• /
• 2009

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.253-257
• /
• 2005

A tube hydroformability testing system was designed and fabricated so as to observe the forming process and to apply forming condition along arbitrarily pre-programmed internal pressure-axial feed path. The forming limit diagram of A6063 extruded tube, of 40.6 mm outer diameter and 2.25 mm thickness, was successfully obtained through free bulging and T-forming tests except the region of high positive minor strain. It is found that the data points marked on the FLD are mostly located near the strain paths from the finite element analysis excluding the cases of large axial feed. There exist data points even in the area beyond the uniaxial tension mode, since the reduction in thickness decreases due to the axial feed. The forming limit from T-forming test was considerably lower than that from free bulge test. It seems because the deformation is localized at the pole.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.9
• /
• pp.939-945
• /
• 2009

The dome stretching tests and tension tests have been performed to obtain a forming limit curve(FLC) for the copper alloy which is used for manufacturing the regenerative cooling thrust chamber. For experimental investigation of the forming limit curve, we have used in-plane tension specimen to obtain tension-compression strain state as well as out-of-plane specimen to obtain tension-tension strain state through dome stretching test. All specimens were divided into longitudinal and transverse directions according to the orientation of test specimen. The test results showed that in the tension-tension region, copper alloy revealed a maximum major strain of 62.3% and a maximum minor strain of 58.6%. In the tension-compression region, the maximum major strain and the maximum minor strain were measured to be 60.5% and 25.8%, respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.68-69
• /
• 2011

마그네슘 판재의 온간 스프링백 거동 예측을 위한 재료 거동 모델을 고찰하였다. V-굽힘 시험에 관한 기존 문헌의 결과와 비교하여 재료 모델의 타당성을 토하였다. 스프링백 거동의 정량화를 위해 온간 S-rail 프레스금형에 의한 성형 시험을 수행하였다. 성형 시험은 다양한 온도, 속도, 성형깊이 조건에서 수행하였으며 시험 결과를 서로 비교하였다. 재료 모델을 사용하여 S-레일 성형에 따른 스프링백 예측을 위한 유한요소해석을 수행하고 그 결과를 시험 측정값과 비교하였다. 이로부터 재료 모델의 한계와 가능성을 고찰하였다.