• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.36-36
• /
• 2015

AZ31B 마그네슘 합금 판재를 이용하여 자동차 부품을 가공하는 경우에는 판재를 성형하고 이를 접합하여 복잡한 형태의 부품을 만들게 되는데, 대부분의 경우에서 전착도장 공정을 필수로 거치게 된다. 그리고 전착도장 공정은 기존의 자동차 생산 공정에 사용되는 도료 및 공정을 그대로 이용하여야 하며, 현재까지 연구된 결과에 의하면 마그네슘 소재의 전착도장은 전착도장 공정 전에 행해지는 화성처리 공정이 적절하게 처리되었다면 공정상 별다른 문제를 발생시키지 않는다. 즉 마그네슘의 화성처리는 전착도장 공정과 전착도장된 제품의 내식성에 매우 중요한 요소이다. 이러한 화성처리 공정은 화성처리 공정 전단계의 표면 전처리 공정에 크게 영향을 받게 되는데, 본 연구에서는 AZ31B 마그네슘 함금 판재의 전처리-화성처리-전착도장으로 구성되는 마그네슘 표면처리에 있어서 전처리 공정중 산에칭 공정이 화성처리-전착도장의 최종 물성에 미치는 영향에 관하여 조사하였다.

• Journal of the Korea Convergence Society
• /
• v.11 no.1
• /
• pp.175-180
• /
• 2020

In this study, we developed a micropattern technology in the shape of RFID TAG antenna using ultrasonic micropattern manufacturing system developed to enable micropattern technology. The ultrasonic tool horn in longitudinal vibration mode was installed in the micropattern manufacturing system to develop the ultrasonic press technology for the micropattern antenna shape of the RFID TAG antenna shape on the insulating sheet surface. The ultrasonic shaping technology was manufactured by applying the resonance design technique to a 60kHz tool horn, and by using the micropattern manufacturing system, the coil wire having a thickness of 25㎛ can be ultrasonically press-molded on an insulating sheet of 200㎛ or less. In ultrasonic press technology, the antenna shape having a minimum line width of 150㎛ could be molded without disconnection, peeling, or twisting of the coil wire.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.1
• /
• pp.1-10
• /
• 2011

An optimization method is proposed for preform and billet shape designs in the forging process by using the Equivalent Static Loads (ESLs). The preform shape is an important factor in the forging process because the quality of the final forging is significantly influenced by it. The ESLSO is used to determine the shape of the preform. In the ESLSO, nonlinear dynamic loads are transformed to the ESLs and linear response optimization is performed using the ESLs. The design is updated in linear response optimization and nonlinear analysis is performed with the updated design. The examples in this paper show that optimization using the ESLs is useful and the design results are satisfactory. Consequently, the optimal preform and billet shapes which produce the desired final shape have been obtained. Nonlinear analysis and linear response optimization of the forging process are performed using the commercial software LS-DYNA and NASTRAN, respectively.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.178-185
• /
• 1999

For the process control of silicon nitride gelcasting, the composition effect of acryamide system on the viscosity of slip and mechanical property of gelcast green body were investigated. The slip was prepared by ball milling of silicon nitride suspension prepared with acrylamide monomer and polyelectrolyte dispersant after premixing them by attritor. The slip mixed with initiator was vacuum deaired and cast into molds, and then polymerized. The consolidated green body was obtained by drying the gelated slip. The viscosity measument and the diametral compression test was done to evaluate the rheological behaviro of slip and mechanical property of gelcast body, respectively. Experimental results showed that the high solid loading of silicon nitride slip was obtained up to 46 vol% with a low viscosity. The mechanical property of gelcast body mainly increased with increasing the concentration of monomer. The gelcast body was machinable above the ∼3 MPa of tensile strength. The relative density of pressured-sintered body was 98.5% at 1760$^{\circ}C$, 3 h.

• Korean Journal of Food Science and Technology
• /
• v.47 no.2
• /
• pp.149-157
• /
• 2015

The effects of feed moisture content (25, 35, and 45%), screw speed (230, 250, and 270 rpm), and barrel temperature (130, 140, and $150^{\circ}C$) on the product yield and soluble arabinoxylan (SAX) content from destarched corn fiber (DCF), and its optimization were investigated. The yield and SAX content of corn fiber gum (CFG) from the extruded destarched corn fiber (EDCF) were higher than those of DCF. Statistical analyses revealed that the feed moisture content and barrel temperature had a significant effect on the CFG yield and total SAX content. The optimum extrusion pretreatment conditions were as follows: feed moisture content, 30%; screw speed, 260 rpm; barrel temperature, $133^{\circ}C$. This study showed that the response surface methodology was suitable for the optimization of the extrusion conditions used to maximize the CFG yield and total SAX content from EDCF.

• Composites Research
• /
• v.33 no.5
• /
• pp.247-250
• /
• 2020

In this study, the possibility of manufacturing a magnesium (Mg) composites reinforced with continuous silicon carbide (SiC) fibers was examined using a liquid pressing process. We fabricated uniformly dispersed SiC fiberAZ91 composites using a liquid phase pressing process. Furthermore, the precipitates were controlled through heat treatment. As a continuous Mg₂Si phase was formed at the interface between the SiC fiber and the AZ91 matrix alloy, the interfacial bonding strength was improved. The tensile strength at room temperature of the prepared composite was 479 MPa, showing excellent mechanical properties.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.289-301
• /
• 1998

The present study attempted to numerically simulate the process in detail by developing an appropriate physical modeling and the corresponding numerical analysis for precision injection and injection/compression molding process of center-gated disk. In part I, a physical modeling and associated numerical analysis of injection molding with a compressible viscoelastic fluid model are presented. In the distribution of birefringence, the packing procedure results in the inner peaks in addition to the outer peaks near the mold surface, and values of the inner peaks increase with the packing time. Also, values of the density in the core region increase with the packing time. From the numerical results, we also found that birefringence becomes smaller as the melt temperature gets higher and that it is insignificantly affected by the flow rate and the mold temperature. As far as the density distribution is concerned, mold temperature affected the distribution of density especially near the wall. But it was not significantly affected by flow rate and melt temperature. Numerical results of birefringence coincided with experimental data qualitatively but didn't quantitatively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.7
• /
• pp.719-725
• /
• 2014

In the present study, a numerical analysis of an injection molding process was conducted for predicting the mold deformation considering non-Newtonian flow, heat transfer, and structural behavior. The accurate prediction of mold deformation during the filling stage is important to successfully design and manufacture a precision injection mold. While the local mold deformation can be caused by various factors, a pressure induced by the polymer melt is considered to be one of the most significant ones. In this regard, the numerical simulation considering both the melt filling and the mold deformation was carried out. A mold core for a 2D axisymmetric center-gated disk was used for the demonstration of the present study. The flow behavior inside the mold cavity and temperature distribution were analyzed along with the core displacement. Also, a Taguchi method was employed to investigate the influence of the relevant parameters including flow velocity, mold core temperature, and melt temperature.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.4
• /
• pp.712-720
• /
• 1988

This paper describes some development of computer-aided system called "COLD-FORMING" and "DESIGN-DIE". "COLD-FORMING" is designed for the forming sequence and "DESIGN-DIE" for the die design of press forming rotationally symmetric parts. The computer program developed is used in interactive and written in BASIC. Design rules for process planning and die design are formulated from process limitations, plasticity theory and know-how of experience of the field. "COLD-FORMING" capabilities include (1) analysis of forming sequence and recognition of individual operation involved each step, (2) determination of intermediate shape and dimensions, (3) calculation of forming loads to perform each forming operation and (4) graphic out put for the operation sheet. "DESIGN-DIE" capabilities include (1) optimum die design corresponding to the output of "COLD-FORMING" and (2) graphic output for the die design.of "COLD-FORMING" and (2) graphic output for the die design.ie design.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.4
• /
• pp.423-430
• /
• 2010

Hot closed-forging process and the die used for forming an automotive flange were analyzed from the viewpoints of heat transfer, grain-flow lines, and stresses to obtain a forged product without defects such as surface cracks, laps, cold shots, and partial filling. The forging process including up-set, pre-forging, final forging and pressing forces was investigated using finite element analysis. The influence of the preform die and the ratio of the heights of the upper die to lower die on the forging process and die were investigated and a die shape ($10^{\circ}$ for the preform die, and 1.5:1 ratio for the final die) suitable to achieve successful forging was determined on the basis of a parametric study. All parametric design requirements such as strength, full filling, and a load limit of 13,000 KN were satisfied for this newly developed flange die. New dies and flanges were fabricated and investigated. Defects such as partial filling and surface cracks were not observed.