• Journal of radiological science and technology
• /
• 제38권3호
• /
• pp.229-235
• /
• 2015

Mammoplasty is currently increasing not only for cosmetic surgery, but as well as for the recovery after breast cancer surgery. The prostheses inserted into the breasts of women who have undergone mammoplasty, hide the breast substances and it is becoming increasingly difficult to diagnose breast disease, and fear is growing by the concern of the prostheses bursting by the strap. So we want to develop a strap applicable to women with prostheses inserted, to determine the usefulness, and we also want to compare the utility by comparing the total area of the Inner and Outer parts of the breast and Posterior Nipple Line (PNL), after obtaining video by applying the existing strap and the developed strap to phantom of the prostheses inserted patient shape. When the pressure by the developed pressure, the total area increased by 10.09% from CC view to $9,813.797mm^2$, 3.88% from CC-ID view to $7,621.531mm^2$, PNL increased by 3.41% from CC view to $90.916mm^2$, 1.64% from CC-ID view to$75.357mm^2$. And the breast tissue of the thorax side increased 3.53% from CC view to $177.725mm^2$, and 6.57% from CC-ID view to $152.510mm^2$, and we could verify that the prostheses were completely eliminated in the CC-ID images of developed strap, compared with the existing strap.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제28권4호
• /
• pp.348-355
• /
• 2006

Tennison was the first to recognize and to preserve the Cupid's bow by lowering the peak in the margin of the cleft. Randall had modified the Tennison's repair based on accurate measurements. Bardach's technique evolved from the basic concept of triangular flap cleft lip repair described by Tennison-Randall method. Precise measurements are used to define the dimensions of the equilateral triangular flap, which is created on the cleft side and is inserted into an equilateral triangular defect on the noncleft side. Two symmetrical vertical distances on either side of the cleft are thus formed. It is essential that the incisions in the skin correspond precisely with those on the muscles and mucosa, and that all layers are sutured with the use of the triangular flap, thus preventing vertical scar contracture. This procedure produces a symmetric, balance lip with a well-defined Cupid's bow, a symmetric vermilion, and a properly aligned orbicularis oris muscle. We had treated three patients with unilateral incomplete cleft lip by using Bardach's triangular flap method. The operation scars could be reduced comparing to Millard method because Bardach's method did not use the columella base and the alar base incision. And the flap design was more simple and accurate comparing to Tennison-Randall method. On the other hand, the postoperative scars on the philtrum pointed as a disadvantage of triangular flap method were cosmetically acceptable because the three patients had incomplete cleft lip. We have experienced that Bardach's triangular flap is a recommendable technique for the repair of unilateral incomplete cleft lip.

• The korean journal of orthodontics
• /
• 제25권1호
• /
• pp.13-18
• /
• 1995

Craniofacial asymmetry was analyzed in 39 patients with complete unilateral cleft lip and palate(UCLP). The samples are devided into three groups nine below 9 years, twenty three from 9 years 1 month to 14 years and seven over 14 years group. Seventeen measurements were obtained from the tracing of PA X-ray cephalometric headfilms to evaluate the asymmetric characteristics and changes accdording to aging in UCLP. The obtained results were as follows. 1. Facial asymmetry in UCLP is variable(1.22-3.47 $mm/^{\circ}$) and the length from midsagitta1 reference line to maxillary 1st molar, to upper central incisor and the length of mandibular ramus showed significant asymmetry 2. Nasal septum and anterior nasal spine were deviated In the cleft side and the lower border of nasal cavity was 1ower in cleft side. 3. The deviation of nasal septum was continued significantly till after 14 years old.

• Journal of the Korean Ceramic Society
• /
• 제34권3호
• /
• pp.303-313
• /
• 1997

To enhance the strength and formability of MCFC matrixes, alumina/${\gamma}$-LiAlO2 fiber-reinforced ${\gamma}$-LiAlO2 ma-trixes have been investigated. The MCFC matrixes with the thickness of 500~600 ${\mu}{\textrm}{m}$ were prepared by tape-casting of the slurry containing 10~30wt% fibers, followed by heat-treating up to $650^{\circ}C$. The porosity of fi-ber-reinforced matrixes decreased with the content of fibers, while the appropriate porosity(50~60%) for MCFC matrixes could be attained by adding larger ${\gamma}$-LiAlO2 particles with the diameter of about 50${\mu}{\textrm}{m}$ up to 50 wt%. The optimum length and content of the alumina fiber, both in the alignment of fibers and the enhancement of the strength, were found to be below 250${\mu}{\textrm}{m}$ and 20 wt%, respectively. On the other hand, the strength(156 gf/$\textrm{mm}^2$) of the ${\gamma}$-LiAlO2 matrix reinforced with ${\gamma}$-LiAlO2 fibers prepared in this study was improved by 20~40% in comparison with the alumina-fiber-reinforced matrix. It was also found that the alu-mina-fiber-reinforced matrix was completely corroded in molten carbonates but the ${\gamma}$-LiAlO2 was not.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• 제49권6호
• /
• pp.447-451
• /
• 2004

This study was conducted to establish the proper techniques of the recirculating wick hydroponics for safe seed tuber proliferation of potatoes (Solanum tuberosum L. CV. Dejima). To achieve these, several intact tubers (5, 10 and 20 g) and cut seed-pieces (two or four) were treated in wick hydroponic system beds. A polystyrene box (31cm in width, 20cm in height, 51cm in length, and $0.031m^3$ in volume) was placed on a styrofoam hox. Eight wicks $(width\;1.5cm\;{\times}\;length\;40cm) $ were put into each polystyrene hox and the boxes were filled with perlite + peatmoss (1 : 2, v/v) medium. Top fresh weight per plant increased with increasing the tuber size from 10 to 30g/tuber. As the tuber size increases from 10 to 30 g/tuher in case of uncut tuber, the marketable tuber (>5g) production per plant increased from 83.8 to 141.8 g/plant and the marketable tuber (>5g) production per plant of cut tuber was slightly higher than that of uncut treatment. Total tuber yield ranged from 4.16 to $6.56kg/m^2$ and the percentage of seed tubers was greater than $97\%$ for all treatments. These results indicate that seed tuber should be cut to produce large tuber $(\geq10g)$ in the recirculating wick hydroponic system.

• Journal of the Korea Concrete Institute
• /
• 제26권4호
• /
• pp.491-497
• /
• 2014

The corrosion of steel reinforcement in reinforced concrete bridge decks significantly affects the degradation of the capacity. Due to the advantageous characteristics such as high tensile strength and non-corrosive property, fiber reinforced polymer (FRP) has been gathering much interest from designers and engineers for possible usage as a alternative reinforcement for a steel reinforcing bar. However, its application has not been widespread, because there data for short- and long-term performance data of FRP reinforced concrete members are insufficient. In this paper, seven full-scale decks with dimensions of $4000{\times}3000{\times}240mm$ were prepared and tested to failure in the laboratory. The test parameter was the bottom reinforcement ratio in transverse direction. The decks were subjected to various levels of concentrated cyclic load with a contact area of $577{\times}231mm$ to simulate the vehicle loading of DB-24 truck wheel loads acting on the center span of the deck. It was observed that the glass FRP (GFRP) reinforced deck on a restraint girder is strongly effected to the level of the applied load rather than the bottom reinforcement ratio. The study results showed that the maximum load less than 58% of the maximum static load can be applied to the deck to resist a fatigue load of 2 million cycles. The fatigue life of the GFRP decks from this study showed the lower and higher fatigue performance than that of ordinary steel and CFRP rebar reinforced concrete deck. respectively.

• Composites Research
• /
• 제12권3호
• /
• pp.84-90
• /
• 1999

High alumina cement(HAC) and polyvinyl alcohol(PVA) based macro-defect-free(MDF) cement composites were reinforced using short carbon fibers, 3mm in length, 1-4% in weight fraction and insoluble polymers such as polyurethane, epoxy, phenol resin, in order to increase mechanical properties and water stability. The specimens were manufactured by the low heat-press(warmpress) method. In addition, the interface and the cross-linking reaction of cement and polymers was also studied by the SEM and TEM. Flexural strength of HAC/PVA based MDF cementitious composites was proportionally decreased with increasing fiber contents due to the undensified structure around fibers. The flexural strength of insoluble polymer added specimen was decreased with increasing fiber contents, while water stability was dramatically improved. Epoxy resin added specimen showed the highest strength with increasing fiber contents, compared with other specimens. The water stability of fiber content 4% added specimen immersed in water presented about 95%, 87% at 3 and 7 days immersed in water, respectively. The interfacial adhesive strength of fiber-matrix was very much improved due to cross linking reaction of polymer and metal ions of cement. Tensile strength of insoluble polymers added composites as linearly increased with increasing the fiber contents. The epoxy resin added specimen also showed highest tensile strength. The 4% fiber added specimen presented 30~80% higher strength than controlled specimen.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 한국분말야금학회 2001년도 추계학술강연 및 발표대회
• /
• pp.30-30
• /
• 2001

$Bi_2Te_3$계 열전재료는 200~400K 정도의 저온에서 네어지 변환효율이 가장 높은 재료로써 열전냉각, 바런재로 등에 응요하기 위하여ㅠ 제조법 및 특서에 관한 많은 연구가 진행되어 왔다. $Bi_2Te_3$계 화합물은 rhombohedral의 결정 구조를 가지는 층상 화 ;물로 결정대칭성으로 인해 연전기적으로 큰 이방성을 나타낸다. 현재는 일반향용고법에 의해서 입자를 a축 방향으로 성장시켜 큰 결정립을 가진 다결정재료를 사용하고 있으나, c면이 매우 취약하기 때문에 가공서이 나쁘다. 따라서 이와같은 단점을 개선하기 위하여 기계적 강도를 높일 수 있는 가공공정 및 합금설계에 대한 연구가 활발히 진행되고 있다. 측히 열간 압출법으로 제조된 열전재료는 결정립의 미세화와 높은 이방성으로 성능지수와 기계적 강도를 향상시킬 수 있다는 연구결과가 보고되고 있다 또한 Schultz드의 연구결과에 의하면 $Bi_2Te_3$ 계 열전재료는 소성변형에 의하여 발생한 점결함에 의하여 캐리어 농도가 변화되며 이로 인하여 재료의 전기적 성질이 결정된다고 하였다. 따라서 상당히 큰 소성가공량과 열전측성과의 관계를 규명하는 것은 매우 중요하다. 이에 본 연구에서는 압출변수 중 소성가공량에 중요한 변수로 작요아는 압출비를 변화시켜 최적의 열간 소성가공량을 검토하고, 이에 따른 열전측성과 압출비와의 상관관계에 대하여 연구하는 것을 목적으로 하였다. 연구에 사용된 N형의 조성은$Bi_2Te_{2.75}Se_{0.15}$로서 순도 99.99를 사용하였고, dopant로 0.1wt%의 $SbI_3$를 사용하였다. $Bi_2Te_{2.75}Se_{0.15}$ 분말은 가스분사법(Gas atomization Process)를 이용하여, 용탕제조시 아르곤가스로 산화를 방지하였고, 냉매로는 질소가스를 이용하였다. 제조된 분말을 기ㅖ적 분급법을 이용하여 분급하였고, 냉매로는 질소가스를 이용하였다. 제조된 분말을 기계적 분급ㅂ법을 이용하여 분급하였고, 압출에 이용된 분말은 250$\mu\textrm{m}$이하의 크기를 사용하였다. 또한 분말제조과정 중 형성되는 표면산화층을 제거하기 위하여 36$0^{\circ}C$에서 4시간동안 수소 환원처리를 행하였다. 제조된 분말은 열간 압출을 위하여 Aㅣcan에 넣고 냉간성형체를 만들고, 진공처리를 한 후 밀봉하여 탈가스처리를 하였다. 압출다이는 압출비가 각각 28:1과 16:1인 평다이(9$0^{\circ}C$)를 사용하여 각각 내경이 9, 12cm이고, 길이가 50, 30cm인 압출재를 제조하였다. 열간압출한 후의 미세조직을 광학현미경으로 압출방향에 평행한 방향과 수직방향으로 관찰하였고, 열간 압출재 이방성을 검토하기 위하여 X선 회절분석을 실실하여 결정방위를 확인하였다. 전기 비저항 및 Seebeck 계수 측정을 위하여 각각 2$\times$2$\times$10$mm^3$ 그리고 5$\times$5$\times$10$mm^3$ 크기의 시편을 준비하였다.준비하였다.

• Journal of the Korean Ceramic Society
• /
• 제40권8호
• /
• pp.758-764
• /
• 2003

The cylindrical ${\gamma}$-alumina pellets were prepared by forming, hydration, drying and calcination after mixing amorphous alumina and pore generating agent with water. Concentration of Fe(NO$_3$)$_3$ㆍ9$H_2O$ that was catalyst precursor was fixed and made mixing solution that changed concentration of $CH_3$COOH in range of 2.5~20%, and here ${\gamma}$-alumina pellets were immerged and were hydrothermaly treated for 3 h at $200^{\circ}C$. And then we investigated creation and change of crystal, pore characteristics, $N_2$ adsorption and desorption isotherms, changes of acid site and mechanical strengths etc. According to the concentration of $CH_3$COOH, the crystals grew to acicular shape of 0.5~2${\mu}m$ length, and crystal structure showed the pseudo-boehmite structure. When hydrothermaly treated in 10% $CH_3$COOH solution, pore volume between 100~1000 $\AA$ was highest by 0.86 cc/g, and width of hysteresis curved line due to $N_2$ adsorption/desorption appeared as was smallest. When concentration of $CH_3$COOH was in range of 5~15%, new C-H functional groups were formed. Mechanical strength of pellets was highest by 1.35 MPa when $CH_3$COOH concentration was 2.5%.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제34권5호
• /
• pp.326-331
• /
• 2012

Purpose: Length measurement from maxillary anterior teeth root tip to nasal floor is incorrect in panoramic radiography. Comparison of cone beam computed tomography (CBCT) and panoramic radiography should be helpful in determining the vertical length. Methods: Sixty nine patients were taken CBCT and panoramic radiography of the maxillary anterior. First measurement is length of parallel lines from the central incisor and lateral incisor root tip to nasal floor on CBCT. Second measurement is length of perpendicular lines from the central incisor and lateral incisor root tip to nasal floor on CBCT. Third measurement is length from the central incisor and lateral incisor root tip to nasal floor on panoramic radiographys. Results: In the first measurement of the maxillary central incisors, an average of $11.36{\pm}2.49$ mm in males and $10.49{\pm}2.17$ mm in females. In the second measurement of the maxillary central incisors, $10.41{\pm}2.42$ mm in males and $9.18{\pm}2.08$ mm in females. In the third measurement of the maxillary central incisors, $10.71{\pm}2.20$ mm in males and $9.27{\pm}2.10$ mm in females. In the first measurement of the maxillary lateral incisors, an average of $13.40{\pm}2.04$ mm in males and $11.96{\pm}2.20$ mm in females. In the second measurement of the maxillary lateral incisors, $11.25{\pm}1.82$ mm in males and $10.06{\pm}1.68$ mm in females. In the third measurement of the maxillary lateral incisors, $11.47{\pm}2.01$ mm in males and $10.13{\pm}1.70$ mm in females. Conclusion: The vertical length from root tip to nasal floor was longer in male than female (P>0.05). First measurement was longer than third measurement (P<0.05). This is the actual placement of the implant site measured on the vertical length than the length of the panorama means that there are a few more free. The first measurement was longer than 114% over the third measurement.