• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.9
• /
• pp.18-25
• /
• 2003

In this paper, thermal conductivities of carbon-phenolic 8-harness satin weave composite, ACP302, were measured and predicted. In the analysis, the satin weave unit cell was identified and modeled discretely by 3-dimensional finite elements, considering the interlaced fiber tow architecture microscopically. At the unit cell boundary, the corresponding periodic boundary conditions were applied. The results were analyzed to investigate the effect of microstructural parameters such as stacking phase shifts, waviness ratio, and fiber volume fraction. The conductivities were also obtained by experiments and compared with the numerical results.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.4
• /
• pp.45-54
• /
• 2013

In this study, various types of composite materials and adhesives that are actually used in the shipbuilding field for small ships, leisure boats, and fishing boats were applied in the hand lay-up method and vacuum infusion method to manufacture specimens. Then the tensile strength, tensile modulus, flexural strength, and flexural modulus values of these specimens were obtained. In addition, the barcol hardness and fiber content were obtained from the specimens. The results showed that the strengths of the specimens manufactured using the vacuum infusion method were higher than those manufactured using the hand lay-up method. Moreover, the barcol hardness and fiber content were also higher in those manufactured using the vacuum infusion method. The specimens manufactured using the vacuum infusion method were thinner despite their large fiber content.

• Korean Journal of Materials Research
• /
• v.4 no.7
• /
• pp.817-822
• /
• 1994

The reinforcing effect of C-shape carbon fiber was investigated as comparing to typical round-shape fiber with similar properties. The results show that C-shape fiber reinforced materials have better in almost all aspects of mechanical properties, or 218% in flexural strength, 223% flexural modulus, 157% interlamina shear strength, 227% impact strength, 184% transverse flexural strength and so on. Also in damping characteristics considerably concerned with fatigue life, friction/wear coefficient of a material, C-CF/EP had about 185% greater. In this research, we present the potential of non-circular fiber reinforcing materials by C-shape carbon fiber.

• Applied Chemistry for Engineering
• /
• v.33 no.5
• /
• pp.471-476
• /
• 2022

PP/KF felt was used to load a high content of kenaf fiber (KF) into polypropylene (PP), and polyurethane (PU) was used as a binder. In order to find an optimum composition ratio of the PU binder, the flexural strength of the PP/KF/PU felt composite according to the isocyanate and polyol ratio was evaluated. PP-g-MAH grafted with maleic anhydride (MAH) was applied as a compatibilizer. Tensile, flexural, and impact properties were evaluated to consider changes in mechanical properties of the PP/KF/PU felt composite, and the properties were improved.

• Elastomers and Composites
• /
• v.46 no.3
• /
• pp.223-230
• /
• 2011

Considering of utilizing renewable resources and recycled plastics, green composites consisted of recycled polyethylene (PE) as matrix and eco-friendly natural fibers as reinforcement were processed and characterized in the present study. First, the wood flour/recycled polyethylene pellets with different wood flour contents were prepared by twin-screw extrusion processing. Using the pellets, wood flour/recycled polyethylene green composites were fabricated and the effects of wood flour loading on their flexural, tensile, impact properties, heat deflection temperature and fracture behavior were investigated. It was concluded that the flexural strength, flexural modulus, tensile modulus and heat deflection temperature of wood flour/recycled polyethylene green composites were increased with wood flour, whereas the tensile strength and impact strength were decreased. The fracture behavior observed by means of scanning electron microscopy supported qualitatively the tendency of the impact strength with wood flour loading, compared with the ductile fracture pattern of recycled polyethylene.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05a
• /
• pp.363-366
• /
• 2012

본 연구에서 NaOH, Acetic acid, Silane 처리는 천연섬유와 matrix간의 계면 결합에 불리하게 작용하는 wax, lignin, hemicellose 등을 제거하기 위한 방법 중의 하나이다. 이러한 화학적 처리에 따른 왕겨 분말의 기계적 특성 변화를 관찰하였다. Scaning electron microscopy(SEM)으로 관찰한 표면의 상태가 NaOH, Acetic acid, Silane 처리를 하였던 왕겨 분말이 처리를 하지 않았던 왕겨 분말보다 비교적 깨끗해지고, 크랙이 발생함을 확인하였다. 또한 전처리가 된 상태에서 PP와 20, 30, 40%의 비율로 복합재를 제조하여 Universal Testing Machine(UTM)으로 인장강도, 굴곡강도, 굴곡탄성률을 측정하였다. 또한, 왕겨의 입도 사이즈에 따라서 어떻게 변화되는지 알아보았다.

• Composites Research
• /
• v.31 no.6
• /
• pp.317-322
• /
• 2018

In various industry, the composite is tried to be applied to products and thermoplastic based composite is in the spotlight because this composite can be recycled. The use of continuous fiber thermoplastic (CFT) method increased gradually than long fiber thermoplastic (LFT). In this study, tensile, flexural, and impact test of different array types of glass fiber (GF)/thermoplastic composites were performed to compare with GF array. Impregnation property between GF mat and thermoplastic was determined using computed tomography (CT). At CFT method, thermoplastic film is not wet into GF roving and many voids are appeared into composite. This phenomenon affects to decrease mechanical properties. Plain pattern GF mat was the best mechanical and impregnation properties that distance between two roving was set closely to $100{\mu}m$.

• Journal of Adhesion and Interface
• /
• v.20 no.3
• /
• pp.87-95
• /
• 2019

In the present study, the effect of alkali treatment of rice straw on the flexural properties and impact strength of rice straw/recycled polyethylene composite was investigated. Alkali treatments were performed by means of two different methods at various sodium hydroxide (NaOH) concentrations. One is static soaking method and the other is dynamic shaking method. The composites were made by compression molding technique using rice straw/recycled polyethylene pellets produced by twin-screw extrusion process. The result strongly depends on the alkali treatment method and concentration. The shaking method done with a low concentration of 1 wt% NaOH exhibits the highest flexural and impact properties whereas the soaking method done with a high concentration of 10 wt% NaOH exhibits the highest properties, being supported qualitatively by the fiber-matrix interfacial bonding of the composites. The properties between the two highest property cases above-described are comparable each other. The study suggests that such a low concentration of 1 wt% NaOH may be used for alkali treatment of natural fibers to improve the flexural and impact properties of resulting composites, rather than using high concentrations of NaOH, 10 wt% or higher. Considering of environmental concerns of alkali treatment, the shaking method is preferable to use.

• Composites Research
• /
• v.23 no.5
• /
• pp.30-38
• /
• 2010

Observing of GMT-Sheet in molding conditions, we have investigated unexpected phenomenons of moldings surface. In microscope investigation, we observe that there exist deficiencies on the surface of GMT-Sheet moldings, such as the spherulite, fiber projection, crack, fiber exposure, micro-weldline, pinhole and winding. They are caused to arise unevenness and phenomenons influence polish on surface. Especially, the major cause of the unevenness, effected to surface roughness, is a shrinking of matrix in the process of holding pressure and cooling temperature. The higher holding pressure load in a molding process and the lower demolding temperature in an annealing experiment, the better GMT-Sheet moldings improved its appearance.

• Composites Research
• /
• v.35 no.2
• /
• pp.75-79
• /
• 2022

In this study, the effect of mechanical and chemical properties of glass fiber reinforced thermoplastic (GFRTPs) according to the number of recycling was confirmed. The composite materials were manufactured through a hot press compression molding process using an E-glass chopped strand mat and a polypropylene film. Four specimens were named according to the number of recycled test repeat: First manufacture, 1st Recycle, 2nd Recycle, and 3rd Recycle. To investigate the mechanical properties of the prepared specimen, tensile test, flexural test, drop-weight impact test, differential scanning calorimetry (DSC), and field emission electron gun-scanning electron microscope (FE-SEM) was performed. As a result, as the number of recycling steps repeat, the degree of crystallization, tensile strength, elastic modulus, and flexural strength were increased, but the impact properties were greatly reduced.