• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.6
• /
• pp.391-398
• /
• 2015

The swing noise of an excavator is reduced in this study. When an excavator is under a swing motion, it produces the annoying noise which is required to be reduced. To identify the characteristics of the swing noise, the signals of noise and vibration from an excavator are measured during the swing motion. From the variation of the driving motor speed, the noise and vibration signals are picked up and plotted in the waterfall plots. From the waterfall plots, we identify the frequency components corresponding to the driving motor frequency, the gear mesh frequency of the planetary gear, and their harmonics. In addition, the natural frequencies and modes of the center frame are extracted by using the experimental modal test. It is found that the swing noise is amplified when the gear mesh frequencies coincide with the natural frequencies of the center frame. To reduce the swing noise, the structural modification is performed to the center frame. Finally, it is observed that the noise is considerably reduced by the structural modification.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.1
• /
• pp.49-56
• /
• 2004

An OFDM system using cross-handed circular Polarization(XCP-OFDM) is newly proposed in his paper. The proposed XCP-OFDM system divides the subchannels into a right-handed circular polarization(RHP channel and a left-handed circular polarization(LHCP) channel that alternate each other. Therefore, the overlaps between subcarriers in XCP-OFDM system can be reduced to a great extend compared to the conventional OFDM system. By this reason, it can improve the orthogonality and reduce the inter-channel interference due to frequency offset. In this paper, it can be seen that the proposed XCP-OFDM system shows robust against frequency offset.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.288-291
• /
• 2011

최근 아스팔트 혼합물의 배합설계법은 기존에 주로 사용하던 빔 및 마샬 배합설계법에서 수퍼페이브 배합설계법으로 점차적으로 바뀌고 있는 추세이다. 수퍼페이브의 배합설계과정에서 중요한 사항 중의 하나는 선회다짐기를 사용하는 다짐방법이다. 아스팔트 포장은 노상 위에 보조기층, 기층, 표층의 순으로 구성되는데 노상은 포장 아래 약 1.0 m의 흙부분으로 포장과 일체로 구성되며 포장체에 작용하는 하중을 최종적으로 지지하는 층이다. 따라서, 수퍼페이브 배합설계법에서 사용하는 선회다짐기를 포장과 일체로 구성되는 노상의 다짐시험에도 적용한다면 각각의 포장층에 같은 원리의 다짐방법을 적용한다는 큰 의미가 있을 것으로 판단된다. 본 논문에서는 일반 노상토에 시멘트와 플라이애시를 첨가한 강화노상토를 선회다짐기를 이용하여 시편을 제작하였고, 각 시편에 대한 탄성계수를 1축압축시험, 공진주시험, LFWD를 이용해 각각 측정하여 각 결과물들의 상관관계를 추정하고자 한다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.6
• /
• pp.61-69
• /
• 2016

This study is the results related to the combustion instability phenomenon with respect to combustor length and thermal power as variables in dual swirling combustor configuration. Especially, the beating phenomena having the insensitive resonance frequency of relatively constant peaks are observed when the combustor lengths increase in a lower power regime. This beating phenomenon might be occurred due to the interacting behaviors of pilot and main burners with different periods. Therefore, such insensitive response seems to be a result of the beating phenomenon with interaction between the pilot and main flames even though the combustor lengths are increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.9
• /
• pp.1247-1254
• /
• 1998

The vaneless diffusers are widely used in industrial centrifugal compressors which are required to operate within a wide flow range. When very high pressure gases are handled by centrifugal compressor. rotating stall is a serious problem because of the occurance of large aerodynamic exciting forces. Rotating stall mostly often occurs in the impellers but it can occur in vaneless diffusers as well. In this experimental study, the rotating stall in vaneless diffuser with radial type centrifugal impeller was measured by changing the flow rate with I-type, X-type hotwire. As the result, it was cleared which type of rotating stall of the impeller stall would occur and how many stall cells would appear relating with the flow rate. As the flow rate reduced, the propagation speed of rotating stall was reduced. But the stall cell number unchanged with respect to the flow rate.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2022.06a
• /
• pp.150-154
• /
• 2022

The Automatic Ship Identification System(AIS) is importantly used to evaluate the trajectory of ships and the possibility of collision between ships. However, it is difficult to provide real-time information due to the limitation of the transmission intervals. Most of the studies to improve this are conducted based on ideal data, so there is a problem that it is hard to respond to the actual situation. Therefore, in this paper, we propose a discrete Kalman filter-based method that reflects the turning angle according to the type of trajectory, to provide real-time position information on real-time data. In addition, the accuracy evaluation of the proposed algorithm is conducted through experiments using actual data.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.2
• /
• pp.131-143
• /
• 2013

Vibration condition monitoring of low-speed rotational slewing bearings is essential ever since it became necessary for a proper maintenance schedule that replaces the slewing bearings installed in massive machinery in the steel industry, among other applications. So far, acoustic emission(AE) is still the primary technique used for dealing with low-speed bearing cases. Few studies employed vibration analysis because the signal generated as a result of the impact between the rolling element and the natural defect spots at low rotational speeds is generally weak and sometimes buried in noise and other interference frequencies. In order to increase the impact energy, some researchers generate artificial defects with a predetermined length, width, and depth of crack on the inner or outer race surfaces. Consequently, the fault frequency of a particular fault is easy to identify. This paper presents the applications of empirical mode decomposition(EMD) and ensemble empirical mode decomposition(EEMD) for measuring vibration signals slewing bearings running at a low rotational speed of 15 rpm. The natural vibration damage data used in this paper are obtained from a Korean industrial company. In this study, EEMD is used to support and clarify the results of the fast Fourier transform(FFT) in identifying bearing fault frequencies.

• Clean Technology
• /
• v.26 no.3
• /
• pp.211-220
• /
• 2020

This experimental study investigates the design parameters to achieve ultra low NOx combustion of coal using a 80 kW capacity single-burner furnace. The influence of key design parameters such as SN, overall and burner-zone equivalence ratios, primary/secondary air ratio, overfire air (OFA) ratio were tested for a total of 81 cases. The results showed that weak swirl intensity of the burner leads to higher NOx emission whereas strong swirl intensity accompanies increased CO concentration desipte lower NOx emission. Therefore, finding an appropirate swirl intensity is essential for the burner design. Larger flow rate of secondary air increased NOx emission, whereas smaller flow rate stretches the flame and increased CO emission. The lowest NOx emission of 82 ppm (6% O₂) was achieved at the optimal condition of the present burner deisgn. It is expected to furrther lower the NOx emission by introducing splitting the burner secondary air into three or four streams.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.41 no.1
• /
• pp.70-77
• /
• 2005

The study was results obtained from the trial make of the hybrid GPS-electromagnetic(EM) compass which overcome shortcoming of GPS compass and EM compass. The results were summarized as follows: GPS compass detected the stable ship's heading at 0.1^{\circ}$ intervals with the turning angular velocity of less than 25^{\circ}$/sec in the experiment for the characteristics of turning angular velocity with stepmotor, but in case of over 25^{\circ}$/sec the compass did not detect it. On the contrary, the EM compass always indicated the ship's heading with no connection of the turning angular velocity, however the compass is low accuracy compared with GPS one owing to a compass error. The ship's headings by the hybrid GPS-EM compass were displayed at fixed point and moving by car; if the GPS compass work the headings were displayed by GPS compass, if not, the heading is provided stably by adding or subtracting of a compass error to the heading of EM compass. Also, each ship's heading was derived from not only the GPS compass but also the EM one by add or subtract of the compass errors, and then was worked covariance for the analogy. The results show that the ship's heading of two compasses has been verified the similarity to 95% confidence level.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.511-519
• /
• 2021

Slewing bearing is applied to the transmission of rotational power of the body and turret in a special vehicle for anti-aircraft weapons that overcomes the enemy flight system approaching at low altitudes with rapid response fire. When the turret load and impact load generated when shooting are combined in performing the combat mission of a special vehicle, structural stability must be secured to achieve a successful function. Among the components of the slewing bearing, the stability of the components against the complex loads acting by the turret drive and shooting was evaluated by considering the shape and material characteristics of the ring-gear, roller, and wire-race. As a research method for stability evaluation, based on engineering theory, the strength characteristics of the components were examined by numerical calculations. Finite element analysis was performed on components using the ANSYS analysis program. The results of theoretical analysis and the results of finite element analysis were very similar. A structural stability evaluation for the slewing bearing, which was performed mainly on the analysis, confirmed that the design strength of the slewing bearing determined in the preliminary design in the early stage of localization development was sufficient.