• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6D
• /
• pp.809-817
• /
• 2008

This paper deals with the development of ViscoElastic Continuum Damage Finite Element Program (VECD-FEP++) and its verification with the results from both field and laboratory accelerated pavement tests. Damage characteristics of asphalt concrete mixture have been defined by Schapery's work potential theory, and uniaxial constant crosshead rate tests were carried out to be used for damage model implementation. VECD-FEP++ predictions were compared with strain responses (longitudinal and transverse strains) under moving wheel loads running at different constant speeds. To this end, an asphalt pavement section (A5) of Korea Expressway Corporation Test Road (KECTR) instrumented with strain gauges were loaded with a dump truck. Also, a series of accelerated pavement fatigue tests have been conducted at pavement sections surfaced with four asphalt concrete mixtures (Dense-graded, SBS, Terpolymer, CR-TB). Planar strain responses were in good agreement with field measurements at base layers, whereas strains at both surface and intermediate layers were found different from simulation results due to the complexity of tire-road contact pressures. Finally, fatigue characteristics of four asphalt mixtures were reasonably described with VECD-FEP++.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.269-269
• /
• 2022

최근 낙동강 하구 기수생태 복원에 있어서 중요한 요소 중 하나는 하굿둑 외해측의 보다 높은 정도를 가지는 조석예보치 산정과 이를 통해 하굿둑 방류량과 해수 유입량을 추정하여 주변 환경 등을 예측할 수 있다. 기수생태 복원이 본격으로 논의가 진행 전인 2016년까지는 하구에서 수km 떨어진 기존 조위관측소(부산 및 가덕도)를 활용하여 하류수위를 예측하여 왔지만 조위 높이와 위상 차이로 인하여 활용이 용이하지 않다. 따라서, 낙동강 하굿둑 인접 외해역에서 조석 영향을 받는 수위관측치를 이용하여 조석조화분해를 통해 조위 예측을 보다 정밀하게 산정하는 것이 필요하다. 연구방법으로는 낙동강 하굿둑 외해역에서 관측된 2016년, 2017년 각각 1년간 10분간격으로 관측자료의 저장상태 및 이상자료 유무를 확인하고, 조석조화분해 프로그램인 TASK2000(Tidal Analysis Software Kit) Package를 이용하여 2016년, 2017년 낙동강 하굿둑 인접 외해역에서 관측된 조위자료를 각각 조석조화분해한 결과로 관측조위와 예측조위 비교하였고, 관측조위와 예측조위를 뺀 성분인 조석잔차성분을 구했다. 조화분해결과, 낙동강 하굿둑 외해역은 일반적인 연안역의 조석과는 달리 하천수의 유출, 배수갑문의 조작, 연안사주지형에 의한 조석변형 등 매우 복잡하고 불규칙적인 특성인 기상성분(기압, 바람 등)에 의한 교란을 고려한다면 예측정확도가 상당부분 확보되는 것으로 나타났다. 또한 장주기 성분과 비선형 조석성분의 크기를 비교해 볼 때 거의 편차가 없이 나타나 조석조화상수를 이용한 예보 가능성을 확인할 수 있었다. 조위검증은 2016년의 1년치의 조석자료를 이용하여 조화분해된 조화상수 63개를 이용하여 2017년의 조석 예보치를 산정하였으며, 이를 2017년의 낙동강 하굿둑 외해역의 조석관측치와 조석예측치를 1대 1 비교하는 방식으로 검증하였고, 이들의 상관관계를 파악하기 위하여 두 성분에 대하여 Regression Analysis를 수행하여 예측조위와 관측조위 사이에는 Pre=0.9535×Obs+0.396과 같은 관계식이 성립하는 것으로 분석되었다. 또한, 두 성분간의 상관도는 0.9535로 높게 나타났다. 조위예측 프로그램인 TASK2000 Package 중 MARIE를 이용한 조위예측 프로그램의 신뢰도가 매우 높은 것으로 판단되고, 해당년도 조위예측 시에는 가능하면 직전년도의 1년 조석관측자료를 조화분해하고 얻어진 조화상수를 이용하여 조위예측을 실시하면 보다 정확한 자료를 얻을 수 있다.

• Journal of Korea Water Resources Association
• /
• v.56 no.12
• /
• pp.939-953
• /
• 2023

Shallow water equations (SWE) serve as fundamental equations governing the movement of the water. Traditional numerical approaches for solving these equations generally face various challenges, such as sensitivity to mesh generation, and numerical oscillation, or become more computationally unstable around shock and discontinuities regions. In this study, we present a novel approach that leverages the power of physics-informed neural networks (PINNs) to approximate the solution of the SWE. PINNs integrate physical law directly into the neural network architecture, enabling the accurate approximation of solutions to the SWE. We provide a comprehensive methodology for formulating the SWE within the PINNs framework, encompassing network architecture, training strategy, and data generation techniques. Through the results obtained from experiments, we found that PINNs could be an accurate output solution of SWE when its results were compared with the analytical method. In addition, PINNs also present better performance over the Artificial Neural Network. This study highlights the transformative potential of PINNs in revolutionizing water resources research, offering a new paradigm for accurate and efficient solutions to the SVE.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.1
• /
• pp.49-56
• /
• 2024

An automated dynamic structural analysis module stands as a crucial element within a structural integrated mitigation system. This module must deliver prompt real-time responses to enable timely actions, such as evacuation or warnings, in response to the severity posed by the structural system. The finite element method, a widely adopted approximate structural analysis approach globally, owes its popularity in part to its user-friendly nature. However, the computational efficiency and accuracy of results depend on the user-provided finite element mesh, with the number of elements and their quality playing pivotal roles. This paper introduces a computationally efficient adaptive mesh generation scheme that optimally combines the h-method of node movement and the r-method of element division for mesh refinement. Adaptive mesh generation schemes automatically create finite element meshes, and in this case, representative strain values for a given mesh are employed for error estimates. When applied to dynamic problems analyzed in the time domain, meshes need to be modified at each time step, considering a few hundred or thousand steps. The algorithm's specifics are demonstrated through a standard cantilever beam example subjected to a concentrated load at the free end. Additionally, a portal frame example showcases the generation of various robust meshes. These examples illustrate the adaptive algorithm's capability to produce robust meshes, ensuring reasonable accuracy and efficient computing time. Moreover, the study highlights the potential for the scheme's effective application in complex structural dynamic problems, such as those subjected to seismic or erratic wind loads. It also emphasizes its suitability for general nonlinear analysis problems, establishing the versatility and reliability of the proposed adaptive mesh generation scheme.

• Conservation Science in Museum
• /
• v.31
• /
• pp.1-20
• /
• 2024

The "Buseoksa Temple Gwaebul" (1684, K969) in the possession of the National Museum of Korea is a large Buddhist hanging scroll produced for outdoor rituals (gwaebul) at the eponymous temple. The painting demonstrates the most complex composition among the existing Buddhist hanging scrolls as it depicts the Shakyamuni Buddha in the lower middle, surrounded by the Vairocana Buddha, Medicine Buddha, and Amitabha Buddha. This study examines the characteristics of the background fabric and the production methods of the scroll from Buseoksa Temple and explores the characteristics of the coloring techniques by integrating the results of a non-destructive analysis to determine the materials used for coloring. The gwaebul comprises a total of 13 panels, with 11 panels arranged side by side and one panel each added to the top and bottom. The background fabric of the painting consist of semi-transparent silk tabby for the nine panels in the center, and silk tabby for the four panels surrounding the four sides. The coloring materials used to paint the scroll were analyzed using X-ray fluorescence, and were confirmed to be inorganic pigments of red, yellow, green, blue, and white. For some parts painted in yellow and blue, the colors were expressed by first applying light white pigment before adding organic pigments. In addition, ink was used for the black lines and gold leaf was used for the patterns of the Buddhist robes. X-ray irradiation enabled the determination of the location and technique of coloring according to each pigment color by highlighting the difference in brightness depending on the main component and the thickness of each pigment.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.2
• /
• pp.113-120
• /
• 2005

An understanding of soil-structure interaction is the key to rational and economical design for laterally loaded drilled shafts. It is very difficult to formulate the ultimate lateral capacity into a general equation because of the inherent soil nonlincarity, nonhomogeneity, and complexity enhanced by the three dimensional and asymmetric nature of the problem though extensive research works on the behavior of deep foundations subjected to lateral loads have been conducted for several decades. This study reviews the four most well known methods (i.e., Reese, Broms, Hansen, and Davidson) among many design methods according to the specific site conditions, the drilled shaft geometric characteristics (D/B ratios), and the loading conditions. And the hyperbolic lateral capacities (H$_h$) interpreted by the hyperbolic transformation of the load-displacement curves obtained from model tests carried out as a part of this research have been compared with the ultimate lateral capacities (Hu) predicted by the four methods. The H$_u$ / H$_h$ ratios from Reese's and Hansen's methods are 0.966 and 1.015, respectively, which shows both the two methods yield results very close to the test results. Whereas the H$_u$ predicted by Davidson's method is larger than H$_h$ by about $30\%$, the C.0.V. of the predicted lateral capacities by Davidson is the smallest among the four. Broms' method, the simplest among the few methods, gives H$_u$ / H$_h$ : 0.896, which estimates the ultimate lateral capacity smaller than the others because some other resisting sources against lateral loading are neglected in this method. But it results in one of the most reliable methods with the smallest S.D. in predicting the ultimate lateral capacity. Conclusively, none of the four can be superior to the others in a sense of the accuracy of predicting the ultimate lateral capacity. Also, regardless of how sophisticated or complicated the calculating procedures are, the reliability in the lateral capacity predictions seems to be a different issue.

• Journal of Korean Society for Geospatial Information Science
• /
• v.8 no.1 s.15
• /
• pp.51-63
• /
• 2000

Dynamic traffic assignment(DTA) has been a topic of substantial research during the past decade. While DTA is gradually maturing, many aspects of DTA still need improvement, especially regarding its formulation and solution algerian Recently, with its promise for In(Intelligent Transportation System) and GIS(Geographic Information System) applications, DTA have received increasing attention. This potential also implies higher requirement for DTA modeling, especially regarding its solution efficiency for real-time implementation. But DTA have many mathematical difficulties in searching process due to the complexity of spatial and temporal variables. Although many solution algorithms have been studied, conventional methods cannot iud the solution in case that objective function or constraints is not convex. In this paper, the genetic algorithm to find the solution of DTA is applied and the Merchant-Nemhauser model is used as DTA model because it has a nonconvex constraint set. To handle the nonconvex constraint set the GENOCOP III system which is a kind of the genetic algorithm is used in this study. Results for the sample network have been compared with the results of conventional method.

• Progress in Medical Physics
• /
• v.23 no.2
• /
• pp.114-122
• /
• 2012

For the determination of absorbed dose to water from a linear accelerator photon beams, it needs a exposure calibration factor $N_x$ or air kerma calibration factor $N_k$ of air ionization chamber. We used the exposure calibration factor $N_x$ to find the absorbed dose calibration factors of water in a reference source through the TG-21 and TRS-277 protocol. TG-21 used for determine the absorbed dose in accuracy, but it required complex calculations including the chamber dependent factors. The authors obtained the absorbed dose calibration factor $N_{dw}{^{Co-60}}$ for reduce the complex calculations with unknown $N_{dw}$ only with $N_x$ or $N_k$ calibration factor in a TM31010 (S/N 1055, 1057) ionization chambers. The results showed the uncertainty of calculated $N_{dw}$ of IC-15 which was known the $N_x$ and $N_{dw}$ is within -0.6% in TG-21, but 1.0% in TRS-277. and TM31010 was compared the $N_{dw}$ of SSDL to that of PSDL as shown the 0.4%, -2.8% uncertainty, respectively. The authors experimented with good agreement the calculated $N_{dw}$ is reliable for cross check the discrepancy of the calibration factor with unknown that of TM31010 and IC-15 chamber.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.18 no.1
• /
• pp.1-12
• /
• 2013

Acoustic backscatter profiles were measured by Eco-sounder along an east-west section in the mid-eastern Yellow Sea and at an anchoring station in the low salinity region off the Keum River estuary in September 2012, with observing physical water property structure by CTD. Tidal front was established around the sand ridge developed in 50 m depth region. Internal waves measured by Eco-sounder during low tide period in the eastern side of the sand ridge were nonlinear depression waves with wave height of 15 m and mean wavelength of 500 m. These waves were interpreted into tidal internal waves that were produced by tidal current flowing over the sand ridge to the southeast. When weakly non-linear soliton model was applied, propagation speed and period of these internal depression wave were 50 m/s and 16~18 min. Red tides by Dinoflagelates Cochlodinium were observed in the sea surface where strong acoustic scattering layer was raised up to 7 m. Hourly CTD profiles taken at the anchoring station off the Keum River estuary showed the halocline depth change by tidal current and land-sea breeze. When tidal current flowed strongly to the northeast during flood period and land-breeze of 7 m/s blew to the west, the halocline was temporally raised up as much as 2 m and acoustic profile images showed a complex structure in the surface layer within 5-m depth: in tens of seconds the declined acoustic structure of strong and weak scattering signals alternatively appeared with entrainment and intrusion shape. These acoustic profile structures in the surface mixed layer were observed for the first time in the coastal sea of the mid-eastern Yellow Sea. The acoustic profile images and turbidity data suggest that relatively transparent low-layer water be intruded or entrained into the turbid upper-layer water by vertical shear between flood current and land breeze-induced surface current.

• The korean journal of orthodontics
• /
• v.26 no.1 s.54
• /
• pp.17-32
• /
• 1996

It is important to understand the operating mechanism and force system of fixed appliance that most effective for individual tooth movement in various orthodontic appliances. The archwire system of fixed appliance is devided into 3 types, which is continuous arch, segmented arch and sectional arch. The last two types have longer interbracket distance and simple force operating points, so it is easy to control force system by operator. But the continuous arch has shorter interbracket distance and various bracket geometry, so it is hard to control and anaylze the force system. The purpose of this study was three dimentional force and moment analysis of continuous arch system by finite element method, which is similar situation to three dimentional elastic beam in structural engineering. Several sample form of various bracket geometry and artificial lower crowding typodont made by author were constructed, analyzed and compared each other. The results were as follows : 1. The force magnitude is linear proportional to the degree of displacement or tilting of the bracket. 2. The force magnitude is inversely non-linear proportional to the interbracket distance. 3. In three dimensional typodont model, while the force can be compared with that of the sample form in the area where adjacent bracket geometry is simple, the force is much more than the expected value in the area where adjacent bracket geometry is complex.