• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.2
• /
• pp.243-248
• /
• 2014

The permanent magnet linear synchronous motors facilitate maintenance, for it is structurally simple compare to rotating machine and has lots of advantage such as a precision control, high speed, high thrust and so on. However, it causes an increase of material cost because of structural characteristics that need to arranges the armature on the full length of transportation lines. Thus, in order to resolve this problem, we propose the discontinuous arrangement method of the armature but the edge always exists due to the structure when the armature is arranged discontinuously. Due to this edge, the cogging force is greatly generated and it causes thrust force ripple generating noise, vibration and decline of performance. Therefore, in this paper, we examined the characteristic of end edge according to the skew angle through 3-D numerical analysis using finite element method(FEM) and improved the operation characteristics.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.1
• /
• pp.41-45
• /
• 2008

This paper deals with the estimation method on the initial pole position of a z-axis permanent magnet linear synchronous motor(PMLSM) without magnetic pole sensors such as Hall sensors. The proposed method takes account of the gravitational force at z-axis and also the load conditions. The algorithm consists of two steps. The first step is to approximately estimate the initial q-axis by monitoring the movements due to the test current at predefined different test q-axes. The second step is to estimate the real q-axis as accurately as possible by using the outputs corresponding to torques due to the test current at three different test q-axes in order to avoid the effect of load mass variations. Experimental results on the z-axis PMLSM show good estimation characteristics of the proposed method irrespective of load mass conditions.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.5
• /
• pp.426-430
• /
• 2006

This paper deals with a novel utilization method of the predicted current in the high performance PI current controller with a control time delay. The inevitable error of the predicted current in the linear servo drive using a permanent magnet linear synchronous motor is analyzed and a modified cross-coupling decoupling synchronous frame PI current controller is proposed in order to improve the current control response under both the control time delay and the inevitable current prediction error. Simulation and experimental results show that the proposed current controller has an improved current control performance under both the control time delay and the inevitable current prediction error in the servo drive system.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.11-12
• /
• 2011

본 논문에서는 PWM 인버터에 적합한 새로운 데드타임 보상방법을 제안한다. 최근 PWM 인버터는 교류전동기, 분산전원용 계통연계 시스템 등의 다양한 산업에 사용되고 있다. 그러나 사용되는 전력용 소자의 비선형적인 특성과 데드타임에 의해 전기의 품질이 저하되고 전류에 고조파가 발생하게 된다. 데드타임에 의한 고조파는 정지좌표계 상에서 제 5, 7고조파 동기좌표계상에서 제 6 고조파가 가장 현저하다. 이 논문에서는 동기좌표계 상에서 공진제어기를 사용하여 제 6고조파를 보상하는 방법을 제안한다.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.358-359
• /
• 2011

본 논문에서는 PWM 인버터에 적합한 새로운 데드타임 보상방법을 제안한다. 최근 PWM 인버터는 교류전동기, 분산전원용 계통연계 시스템 등의 다양한 산업에 사용되고 있다. 그러나 사용되는 전력용 소자의 비선형적인 특성과 데드타임에 의해 전기의 품질이 저하되고 전류에 고조파가 발생하게 된다. 데드타임에 의한 고조파는 정지좌표계 상에서 제 5, 7고조파 동기좌표계상에서 제 6 고조파가 가장 현저하다. 이 논문에서는 동기좌표계 상에서 공진제어기를 사용하여 제 6고조파를 보상하는 방법을 제안한다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.5
• /
• pp.94-105
• /
• 2010

To detect faults in an inverter-fed permanent magnet synchronous motor (PMSM) drive under the circumstance having faults in a stator winding and inverter switch, an on-line basis fault detecting scheme during operation is presented. The proposed scheme is achieved by monitoring the second-order harmonic component in q-axis current and the fault is detected by comparing these components with those in normal conditions. The linear interpolation method is employed to determine the harmonic data in normal operating conditions. As soon as the fault is detected, the operating mode is changed to identify a fault type using the phase current waveform. To verify the effectiveness of the proposed fault detecting scheme, a test motor to allow inter-turn short in the stator winding has been built. The entire control algorithm is implemented using DSP TMS320F28335. Without requiring an additional hardware, the fault can be effectively detected by the proposed scheme during operation so long as the steady-state condition is satisfied.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.3
• /
• pp.167-178
• /
• 2010

To diagnose a stator winding fault caused by a short-circuited turn in a permanent magnet synchronous motor (PMSM), an on-line based fault detecting scheme during motor operation is presented. The proposed scheme is based on monitoring the second-order harmonic components in q-axis current obtained through the harmonic analysis and a winding fault is detected by comparing these components with those in normal conditions. The linear interpolation method is employed to determine harmonic data in arbitrary normal operating conditions. To verify the effectiveness of the proposed fault detecting scheme, a test motor to allow inter-turn short in the stator winding has been built. The entire control system including harmonic analysis algorithm and fault detecting algorithm is implemented using DSP TMS320F28335. The proposed scheme does not require any additional hardware and can effectively detect a fault during motor operation so long as the steady-state condition is satisfied.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.12
• /
• pp.71-77
• /
• 2010

A discontinuity of magnetic circuits according to the end effect is generated in PMLSM. And magnetic state of the 3 phase coils becomes unbalanced. Due to the unbalanced magnetic state, the unbalanced flux linkage, back electro-magnetic force and inductance of the 3 phase coils appear. In result, the circulating current is generated by unbalanced inductance even if the input voltages are in balanced state. Then the thrust and efficiency are decreased because of the circulating current. Therefore, in this paper, the unbalanced inductance and the thrust reduction according to discontinuity of magnetic circuits are analyzed by FEA(2D). To demonstrate the validity of the analysis results, the experiment results are compared with analysis results.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.973.1_974.1
• /
• 2009

One of the most important technical improvement required for ropeless elevator system to become practical is the improvements in overall system efficiency. Moreover, the predominant drawback of permanent magnet (PM) linear synchronous motor (LSM) is large detent force. Therefore, for the given volume the selection of high power density PM-LSM with low detent force is very imperative. In this paper, we will investigate the characteristics of thrust and detent force of PM-LSM under different motor topology structure. Finally, the long stator double-sided iron core type PM-LSM with fractional slot winding is the best choice for the ropeless elevator system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.11
• /
• pp.1820-1826
• /
• 2016

This paper deals with dynamic characteristics of the experimental magnetic levitation vehicle employing LSM(Linear Synchronous Motor) for propulsion. To predict the dynamic characteristics of the system, the dynamic model which is composed of the electrical elements such as electromagnets and LSM and mechanical components and is developed based on multibody dynamics is developed. The resulting system equations of motion for the model are a coupled one representing all the mechanical and electrical parts. To verify the dynamic model of the system, air gaps are measured in both running tests and simulation, and the frequency characteristics of air gaps are analyzed. From the results, it can be seen that the frequency responses are almost the same. Finally, to evaluate the levitation stability and the designed controller, numerical simulations are carried out.