• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.4
• /
• pp.1-6
• /
• 1992

The finite difference simulation method for ship waves is introduced for hull form improvement. Numerical simulations were performed for a series of modified hull forms and the simulated results were used for the determination of the better hull forms. A 4,400 TEU container carrier which was designed and experimented in towing tank was chosen for the purpose. The calculation results are compared with those of model test, of simplified Neumann-kelvin problems and of Rankine source method. In this study, it is shown that the combination of the computer simulation by our method with the experiment provides one of the most economical and reliable procedures of hull form improvement and that the degree of accuracy of this method is so high that it can cope with very practical design purposes.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.5
• /
• pp.601-608
• /
• 2019

In this study, the effect of hull appendages on the high-speed catamarans with reverse bow shapes is compared and analyzed by numerical analysis and circulating water tank model test. The reverse bow shape showed an improved wave shape by shifting the generation position of forward divergent wave to the stern direction and was effective in resistance and stable running posture (Kim et al., 2019). In the model test results of the running performance as the wave patterns and the change of the running posture due to the fin fitted with the inner side of the inverted bow and the interceptor, 1) Trim characteristics of the inverted bow 2) Improvement of superposition of inner wave by Fin 3) The trim control by the fin and the interceptor is considered to be effective in reducing the impact of the two hull connection decks (wetdeck).

• Journal of Ocean Engineering and Technology
• /
• v.23 no.4
• /
• pp.38-46
• /
• 2009

Two sets of numerical simulations were carried out for a planing hull model ship. In the first, the WAVIS 1.4 linear and nonlinear potential solver was utilized with the free support condition, in which the running posture was determined during calculation. The linear and nonlinear potential calculation results showed qualitative agreement in the trim and resistance coefficient with the MOERI towing tank test. However, the nonlinear potential calculation gave better results than the linear method. In the next simulation, Fluent 6.3.26 with a VOF model and the WAVIS 1.4 nonlinear potential solver were used with the given running posture from the measurement carried out in the MOERI towing tank. Fluent with the VOF method had substantially better agreement with model test results than the results from the WAVIS nonlinear potential calculation for the total resistance coefficient, and for the bow and stern wave patterns, in spite of the much greater computational costs. Both methods can be utilized in planing hull design when their limitations are perceived, and the running posture should be predicted correctly.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.2
• /
• pp.246-252
• /
• 2016

In this study, conceptual design of the fore-body hull form of catamaran type dredging vessel was performed that can effectively remove the contaminated sediments in coastal seabed. The hull form was simpled for the easy hull construction and the resistance performance was investigated to find out the effect of hull form parameters between variation of waterline and angle of entrance, etc. The relation between resistance performance and characteristics of free surface flows according to variation of bow forms was investigated by model testing in the circulating water channel and using Ansys CFX. The improvement of ship resistance performance to the wave resistance decrease due to improved wave pattern has been verified according to move the stem and the volume of the shoulder to the fore part of the vessel.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.5 s.54
• /
• pp.88-94
• /
• 2003

A series of tests of 5 model ships, selected from a data survey of 10 Gross Tonnage actual fishing boats, were performed in two circulating water channels (Chosun University in Korea and WJFEL in Japan), in order to develop the basic hull form of a 25 knots-class fishing boat. Resistance tests, trim and sinkage measurements and wave pattern observations etc., were included in each I1wdel test, and the model test results were compared and analyzed. The result was as follows: P-4 hull form ship changed into Deep V type bow is the best hull form with good performance, especially with regard to ship's resistance efficiency.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.05a
• /
• pp.130-134
• /
• 2007

단일 구동회로를 사용하여 패널전체를 동시에 방전시킬 수 있는 새로운 priming 방전기술을 고안하였다. 그리고 이 기술을 사용하여 1080개의 수평주사선수를 가지는 full-HDTV PDP를 고휘도로 구동할 수 있는 새로운 고속 구동방식을 제안하였다. 이 priming 방전기술을 사용하면 구동방식에 상관없이 priming 기간을 sustain 기간에 중첩시키고 ramp 파형을 가지는 priming pulse를 인가하는 것이 가능하다. 실험결과로부터 sustain 방전이 없는 경우에만 priming 방전이 일어났다. 그리고 sustain 방전은 priming 펄스의 영향을 거의 받지 않는다는 것이 확인되었다. 새로운 PDP 구동기술로 $0.7{\mu}s$의 address 펄스폭을 가지는 고속 address를 실현하였다. 그리고 40V의 넓은 address 동작마진을 얻었다. 이 기술들은 상용의 driver IC를 사용할 수 있도록 설계되어있으므로 상용화 가능성도 높다.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.253-253
• /
• 2017

본 연구에서는 연륙연도 사업에 대응하는 경제성 및 안정성을 갖춘 쌍동선형 차도선의 개발을 위해 U형과 V형의 서로 다른 쌍동선형을 CFD 해석을 수행하여 저항성능을 비교하였다. CFD 해석 결과 U형 쌍동선형의 경우 14kts 이상의 고속에서 선수부 파형에 이상이 발생하여 정상적인 운행이 불가능하다 판단되었으며, 이에 비해 V형은 동일한 속도에서도 이상이 발생하지 않았으며, 또한 U형 쌍동선형 대비 V형 쌍동선형의 경우, 저속에서는 U형 대비 높은 침수표면적에도 불구하고 거의 같은 $R_{TS}$값을 보이지만, 고속으로 넘어가면 U형에 비해 확연히 낮은 $R_{TS}$값을 보임을 확인, V형의 쌍동선형이 U형에 비해 저항성능이 개선됨을 확인하였다.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.25 no.4
• /
• pp.13-27
• /
• 1988

Two version of the TUMMAC(Tokyo University Modified Marker-And-Cell) method, i.e., $TUMMAC-IV_{vm1}$ and TUMMAC-VI are applied to two water-wave problems. The ship wave of a Series 60 model($C_B=0.6$) and of the fore-body of a HSVA tanker model are simulated by the $TUMMAC-IV_{vm1}$ method are the results are compared with the experimental results. From the comparison with the experimental data it is ascertained that the $TUMMAC-IV_{vm1}$ method is useful for the analysis of the realized by the TUMMAC-VI method is useful for the analysis of the characteristics of nonlinear ship waves. Three-dimensional wave breaking is realized by the TUMMAC-VI method in the simulation of a flow about a vertical rectangular cylinder. From the results of this simulation, it is shown that the TUMMAC-VI method is very available for the simulation of 3-dimensional wave breaking phenomena.

• Journal of Navigation and Port Research
• /
• v.37 no.2
• /
• pp.143-148
• /
• 2013

The aim of this study is to investigate the characteristics on the profile of local ice load acting on side shell of port side in bow part due to broken ice during icebreaking of ships in ice covered waters. The first Korean icebreaking research vessel 'ARAON' had a sea ice field trial in the Arctic Sea during early August, 2010, and the signals due to local ice impact measured from several strain gauges installed at bow part were gathered. It is known that these data with structural response characteristics due to local ice impact have some different characteristics with a typical hydraulic impact pressure - time history. In this study, the time history on the measured signals was analyzed and the characteristic values were presented using non-dimensional parameters.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.8
• /
• pp.27-33
• /
• 2007

A novel priming discharge technique in which the ramp shaped priming pulse is superposed on the sustain period so that the entire plasma display panel (PDP) is discharged at the same time with a single drive circuit is proposed. From the experimental results, it is ascertained that the priming discharge is ignited only in a pixel in which sustain discharge does not occur and it has been understood that the priming pulse hardly influences the sustain discharge. Moreover, high-speed driving with address pulse widths of 0.7[${\mu}s$] was achieved and a wide address voltage margin of 40[V] was obtained by using the drive method applied the proposed priming discharge technique. In these results, full-HDTV PDP with 1080 horizontal scanning lines can be driven without decreasing the brightness and the possibility of the commercializing is also high because this technology is designed for using the commercialized driver IC.