• Economic and Environmental Geology
• /
• v.44 no.3
• /
• pp.203-215
• /
• 2011

Geochemical and mineralogical properties of a contamited soil should be taken into account to decide a remediation strategy for a given contaminant because development and optimization of soil remedial technologies are based on geochemical and mineralogical separation techniques. The objective of this study was to investigate the geochemical and mineralogical characteristics of arsenic-contaminated soils. The arsenic-contaminated soil samples were obtained from Chonam gold mine, Gwangyang, Chonnam, Particle size analysis, sequential extraction, and mineralogical analyses were used to characterize geochemical and mineralogical characteristics of the As-contaminated soils. Particle size analyses of the As-contaminated soils showed the soils contained 17-36% sand, 25-54% silt, 9-28% clay and the soil texture were sandy loam, loam, and silt loam. The soil pH ranged from 4.5 to 6.6. The amount of arsenic concentrations from the sequential soil leaching is mainly associated with iron oxides (1 to 75%) and residuals (12 to 91%). Major minerals of sand and silt fractions in the soils were feldspar, kaolinite, mica, and quartz and minor mineral of which is an iron oxide. Major minerals of clay fraction were composed of illite, kaolinite, quartz, and vermiculite. And minor minerals are iron oxide and rutile. The geochemical and mineralogical analyses indicated the arsenic is adsorbed or coprecipitated with iron oxides or phyllosilicate minerals. The results may provide understanding of geochemical and mineralogical characteristics for the site remediation of arsenic-contaminated soils.

• Economic and Environmental Geology
• /
• v.39 no.2 s.177
• /
• pp.191-212
• /
• 2006

Placer gold deposits is mainly distributed in the Takaoi area. The alluvium is unconsolidated or semiconsolidated deposit consisting of gravel, sand, and soil beds in ascending order. They unconformably overlies the Carboniferous-Permian schist and Cretaceous granodiorite substratum. Based on detailed facies analysis, the alluvium can be interpreted as a typical fluvial deposits containing gravel and sand beds of channel-fill unit and soil deposit of floodplain. Gold grains are included mainly in the gravel bed and vein quartz is only contained gold among all kinds of gravels. These features indicates that the source rock of the gold grain is vein quartz and gold grains are separated from vein quartz during transport and abrasion. The reserves of gold in this area reach to at least 792 kg.

• Journal of the Korean Geographical Society
• /
• v.38 no.4
• /
• pp.505-517
• /
• 2003

The purpose of this paper is to examine the origin of materials of sanddune in the Chungcheongnamdo. The sands consist mainly of quartz with lesser amount of feldspar and other heavy minerals. With the exception of those from the granite, the sands have a very fine texture. Another characteristic of the sand grains is the low degrees of roundness and grading which indicates that the source areas of the material are not far from the accumulating field. The rivers and streams of this region are not effective in transporting sediments for the coastal dunes. It has been recognized that the beaches and sanddunes have recently been receded as a result of the decrease in materials and the devastating actions of the breakers. The degradation process occurs most actively when the spring tides attack the beaches and foredunes. There are strata with red tint along the coastal areas of the Chungcheongnamdo which trace their origin back to the Pleistocene. From the fact that they contain little or no gravels, the strata are believed to have been the sanddunes during the last interglacial period. This fossil dunes provide part of the materials for the development of the present-day sanddunes along the coastal areas of the region.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.3
• /
• pp.203-212
• /
• 2007

Mineral compositions of 89 Yellow Sea surface sediments collected at the second cruise in 2001, were determined using the high resolution X-ray diffractometer and Siroquant v.3.0 program. Yellow Sea surface sediments are composed of major minerals (quartz 57.8%, plagioclase 16.0% and alkali feldspar 10.0%), clay minerals, and calcite. Illite (8.7%) is the most abundant clay mineral, chlorite (2.6%) is the second, and kaolinite (0.6%) is few. however smectite is not detected. Quartz content is very high around the margin of the Yellow Sea, however is very low along the northwest to southeast direction extending from southeast of Sandong Peninsula to southwest of Jeju Island. It has similar distribution pattern with that of coarse sediment (sand). The coarse sediment, is mainly consisted of quartz, may be much supplied from the eastern part and southwestern part of the Yellow Sea. Illite distribution pattern is opposite to that of quartz. It is similar to those of clay and mud particles, therefore it can be suggested that fine sediment may be largely supplied from the northwestern part of the Yellow Sea. It is necessary to continue this kind of investigation, because it is difficult to interpret the sediment provenance of the Yellow Sea only from the result of this study.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.2
• /
• pp.19-32
• /
• 2014

Carbonate sand of Sabkha layer in the middle east was made of deposition of shell fragments and it consisted of porous particles containing inner void. Generally, at yield stress the soil structure begins to break down, so the porewater pressure and the settlement are increased rapidly. In carbonate sand, unlike quartz sand if particle crushing happens, the inner voids are exposed and porewater pressure can be decreased under yield stress. Porewater pressure can be determined as the sum of excess porewater pressure due to increase of relative density, inner void expose of particle under particle crushing stress and rearrangement of crushed particle fragments. The porewater pressure can be negative value in case of greater amount of inner void expose, so if particle crushing is bigger, the porewater pressure value is smaller. The negative value zone of porewater pressure from triaxial test result means particle crushing effect is bigger than outer void decrease effect and the particle crushing effect dominant zone size was 1.50∼3.46% from triaxial test result of Sabkha layer.

• The Journal of Engineering Geology
• /
• v.23 no.3
• /
• pp.247-256
• /
• 2013

The carbonate sands of the Sabkha layer in the Middle East have very low shear strength. Therefore, instant settlement and time-dependent secondary settlement occur when inner voids are exposed, as in the case of particle crushing. We analyzed settlement of the Sabkha layer under a large-scale foundation by hydrotesting, and compared the field test results with the results of laboratory tests. With ongoing particle crushing, we observed the following stress-strain behaviors: strain-hardening (Sabkha GL-1.5 m), strain-perfect (Sabkha GL-7.0 m), and strain-softening (Sabkha GL-7.5 m). General shear failure occurred most frequently in dense sand and firm ground. Although the stress-strain behavior of Sabkha layer carbonate sand that of strain-softening, the particle crushing strength was low compared with the strain-hardening and strain-perfect behaviors. The stress-strain behaviors differ between carbonate sand and quartz sand. If the relative density of quartz sand is increased, the shear strength is also increased. Continuous secondary compression settlement occurred during the hydrotests, after the dissipation of porewater pressure. Particle crushing strength is relatively low in the Sabkha layer and its stress-strain behavior is strain-softening or strain-perfect. The particle crushing effect is dominant factor affecting foundation settlement in the Sabkha layer.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.1
• /
• pp.54-60
• /
• 2006

[ $MnO_2$ ]-Coated Sand(MCS) was prepared with variation of coating temperature, coating time, and dosage of initial Fe(III) with two kinds of sands such as Joomoonjin and quartz sand. An optimum condition for the preparation MCS was determined from the coating efficiency as well as the oxidation efficiency of As(III). Coating efficiency of Mn was strongly dependent on the coating temperature but quite similar over the investigated coating time, showing an increased coating efficiency at higher coating temperature. In contrast to coating efficiency, the oxidation efficiency of As(III) by MCS was severely reduced as increase of coaling temperature. By considering these results, an optimum coating temperature and time for the preparation of MCS was selected as $150^{\circ}C$ and 1-hr, respectively. Coating efficiency increased as the dosage of initial Mn(II) increased, while As(III) oxidation was maximum at 0.8 Mn(II) mol/kg sand. The solution pH was identified as an important parameter affecting stability of MCS, and dissolution of Mn from MCS increased as pH decreased. Oxidation rate of As(III) increased as the dosage of MCS increased as well as solution pH decreased.

• Journal of Conservation Science
• /
• v.34 no.6
• /
• pp.557-568
• /
• 2018

The manufacturing techniques were studied by investigating a precise analysis on wall structure, features of materials and the painting layer of the bracket mural paintings at Daeungbojeon Hall in Naesosa temple. The wall frame is a single-branch structure, and The mural paintings are composed of 3 layers which are a support layer, a finishing layer and a painting layer. The support layer and the finishing layer are an earth wall that sand and clay such as Quartz, Feldspar, and etc. are mixed. The support and the finishing layers have a combination of medium particle sand and smaller than fine particle sand in the approximate ratios of 0.8:9.2 and 6:4, respectively. Therefore, the aforementioned ratio of sand with medium or large particles is relatively higher in the finishing layer than the support layer. As a result of a precise analysis on the painting layer, it has a relatively thick ground layer for painting which is maximum $456.15{\mu}m$ by using Celadonite or Glauconite and the paintings were colored by using pigments such as Atacamite, Kaolinite or Halloysite, Oxidized steel, and etc. on it. The manufacturing style and the painting techniques of an earth wall are included in the category of the Joseon Dynasty style that have been studied up to now, but the facts that the finishing layer has a high content of sand and a middle layer and chopped straw have not been identified. These are remarkable points in terms of structure and materials, and can be crucial in the evaluation of the state of conservation of mural paintings or preparation of a conservation plan.

• Journal of The Geomorphological Association of Korea
• /
• v.18 no.4
• /
• pp.177-191
• /
• 2011

This paper describes a dune field on shoreline of Young Gwang. To clarify geomorphic characteristics, made an analysis of grain size of the sand sediments samples and surface texture of quartz grains, and field survey. The following results were obtained : 1) Young Gwang sand dune is taking to pieces by human impact, and dose not move ahead the process of sand dune. 2) there was a turbulence of sand sediments outcrops saying to the cryoturbation that represents cold climatic environments, 3) Constituents of sand dune are mainly fine and very fine sand(2.5~4.5Φ) consisted by quartz and feldspar. Young Gwang sand grians have some analogy with different sites in west coast 4) In surface texture, roundness is thought to have been formed sub-angular, and some V cracks represented mechanical weathering environments. Especially, the dune environment has significant cultural and archaeological values arising from the occupation of human in the past. Those areas where occupation is known provide a valuable source of past records relating to human settlement.

• Economic and Environmental Geology
• /
• v.47 no.2
• /
• pp.87-96
• /
• 2014

The objectives of this study were to characterize the physicochemical properties and mineralogy of Hwangto (yellow residual soils) from the southwestern part of Korea and to understand the soil-forming processes of the residual soils from their parent rocks. Both the yellowish residual soils as well as the unweathered and weathered parent rocks were obtained from Jangdong-ri, Donggang-myun, Naju, Jeollanam-do, Korea. The soil samples were examined to analyze the said soil's physicochemical properties such as color, pH, and particle size distribution. A scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis, transmission electron microscopy (TEM) and X-ray diffraction (XRD) analysis were performed in order to understand the mineralogy, chemical composition, and morphology of the soils. Two thin sections of a parent rock were analyzed to study its mineral composition. A particle size analysis of the soils indicates that the residual soil consists of mainly silt and clay (approximately 95%) and that soil textures are silty clay or silt clay loam. The soil colors of the residual soil are dark brown (7.5YR 3/4) through yellowish red (5YR 4/6). The pH of the residual soil ranges from 4.3 to 5.1. The major minerals of the parent rocks were quartz, biotite, chlorite, and plagioclase. The mineralogy of the sand fraction of the residual soil was quartz, biotite, muscovite and sanidine. The mineralogy of the silt fraction of the residual soil was quartz, biotite, muscovite, Na-feldspar, K-feldspar, and sanidine. The clay mineralogy of the soil was goethite, kaolinite, ilite, hydroxy-interlayed vermiculite(HIV), vermiculite, mica, K-feldspar and quartz. The mineral composition of the residual soil and the parent rock indicates that feldspar and mica in the parent rock weathered into illite, vermiculite and hydroxy-interlayed vermiculite(HIV), and finally changed into kaolinite and halloysite in the yellowish residual soils.