• Applied Chemistry for Engineering
• /
• v.30 no.5
• /
• pp.620-626
• /
• 2019

In this study, the effects of the structural properties of the catalyst on CO oxidation reaction by controlling the $Cu/CeO_2$ catalyst amount and calcination temperature were studied, and also the CO conversion rate of the catalyst at the temperature range of $100{\sim}300^{\circ}C$ was evaluated. XRD, Raman, BET, $H_2-TPR$, and XPS analyses were performed to confirm the effect of changes in the structural properties on the chemical properties of the catalyst. The result confirmed that a substitution bond between Cu and Ce was formed and a lot of Cu and Ce bonds were formed when the catalyst carrying 5 wt.%. Of Cu was calcined at $400^{\circ}C$. The Cu-Ce binding was confirmed by peak shifts in Raman analysis and also peaks appeared in $H_2-TPR$. In addition, the balance state analysis demonstrated that a lot of surface labile oxygen molecules are formed, which can be more easily contributed to the reaction with $Ce^{3+}$ species known to form a substitution bond easily. It was found that CO conversion rate of the catalyst used in this study was close to 100% at $150^{\circ}C$.

• Land and Housing Review
• /
• v.12 no.3
• /
• pp.79-85
• /
• 2021

This study analyzed the energy consumption differences between rental and owner owned (purchased) apartments in Busan, South Korea during the cooling and heating seasons. Analysis revealed that the average electricity consumed for cooling was 2.5 kWh/m²·yr for rental apartments and 2.3 kWh/m²·yr for purchased apartments, a difference of 0.2 kWh/m²·yr. The average electrical heating energy consumption was 3.3 kWh/m²·yr for rental apartments and 2.2 kWh/m²·yr for purchased apartments, a difference of 1.1 kWh/m²·yr. It was estimated that the use of electric blankets and heaters was higher in rental apartments than purchased apartments resulting in higher electrical heating energy consumption. The average gas heating energy consumption was 7.0 kWh/m²·month for rental apartments and 6.8 kWh/m²·month for purchased apartments. When electricity and gas usage was combined for heating, the average total heating energy consumption was 10.3 kWh/m²·month for rental apartments and 9.0 kWh/m²·month for purchased apartments. This indicates that rental apartments consume 1.3 kWh/m²·month more energy than purchased apartments during heating season. Overall, rental apartments consume more energy than purchased apartments during both the cooling and heating seasons.

• Journal of Adhesion and Interface
• /
• v.22 no.3
• /
• pp.98-105
• /
• 2021

In this study, we prepared a silver nanoparticle transferable adhesive composition with transparency and adhesive properties using UV-curable urethane acrylate containing silane groups. The urethane-based adhesive composition was applied between the Ag/PET film in which silver nanoparticles were patterned on PET and the PC film to be transferred. Immediately after UV-curing with UV, PET was removed to complete the manufacture of Ag/PC film. UV-curable urethane acrylate containing silane groups was synthesized using polycaprolactone diol (PCL), isophrone diisocyanate (IPDI), 2-hydroxyethyl methacrylate (HEMA), and (3-aminopropyl) triethoxysilane (APTES). The silane group of APTES can improve interfacial adhesion by reacting with the specially treated silver nanoparticle surface of the Ag/PET film. In addition, we improved the adhesion between silver nanoparticle and PC film by mixing UV-curable urethane acrylate containing a silane group and a functional acrylic diluent used as a diluent. We analyzed the synthesis process of urethane acrylate using FT-IR, and compared the adhesive properties, optical properties, and transfer properties according to the molar ratio of APTES and the acrylic diluent composition. As a result, the best transfer properties were confirmed in the adhesive composition prepared under the conditions of PUA2S1_0.5.

• The Korean Journal of Archival Studies
• /
• no.13
• /
• pp.41-90
• /
• 2006

It's needed for the archivists to design a flexible and stable ERMS(Electronic Records Management System) which can ingest and store records through a consistent way and let users search and use records easily what they want. The basis of the design for ERMS are the conceptual composition and the logical and physical structure of the records when they are stored and managed in the ERMS. This paper explains the process of defining components and designing structure of electronic records using 3-layered approaches which consist of conceptual, logical and physical layer and shows advantages of this approaches. After benchmarking the information models of OAIS which is a reference model for the long-term preservation of digital information objects, this paper applies the model of AIP to a record as a 'Record AIP' and discusses the composition and structure of it. It's a critical task to identify mandatory or optional metadata groups which consists of the 'Record AIP's in the conceptual layer. This paper emphases that the metadata group related to services for the record information to users is required as a result of benchmarking OAIS information models. Various issues about the structure of 'Record AIP's are discussed according to the kind of preservation strategy such as migration or emulation and whether the encapsulation of records is required or not in the logical layer.

• Journal of Digital Convergence
• /
• v.17 no.3
• /
• pp.235-251
• /
• 2019

The purpose of this study was to investigate the single-person household's demand for a wearable healthcare system that provides the ischemic heart disease and cardiopulmonary alarm to be developed. In this study, in-depth interviews were conducted with six unmarried individuals in their thirties who were in the workplace and the results were interpreted by Giorgi's phenomenological analysis method. The study results indicated that although the wearable healthcare system was implemented with high-technology functions that serve the intended purpose, it is necessary to comprehensively consider factors such as aesthetics, comfort, and ease of washing. In this study, we found that the variables influencing the interviewees' intent to accept healthcare services are complex and cannot be attributed to one factor alone; this study has also shown a variety of interpersonal correlations. In addition, although health-care research focusing on the elderly has been conducted in the past, it is suggested that younger generations such as those in their thirties can also be studied as health care service adopters.

• Journal of Korea Water Resources Association
• /
• v.51 no.spc
• /
• pp.1117-1126
• /
• 2018

Water supply system aims to meet the user's demand by securing water resources in a stable way. However, water supply failure sometimes happens because inflow decreases during drought period. Droughts induced by the lack of precipitation do not always lead to water supply failures. Thus, it is necessary to consider features of actual water shortage event when we evaluate a water supply risk. In this study, we developed a new drought index for drought management, i.e., Joint Drought Management Index (JDMI), using two water supply system performance indices such as reliability and vulnerability. Future data that were estimated from GCMs according to RCP 4.5 and 8.5 scenarios were used to estimate future water supply risk. After dividing the future period into three parts, the risk of water supply failure in the Nakdong River basin was analyzed using the JDMI. As a result, the risk was higher with the RCP 4.5 than the RCP 8.5. In case of RCP 4.5, W18 (Namgangdam) was identified as the most vulnerable area, whereas in case of RCP 8.5, W23 (Hyeongsangang) and W33 (Nakdonggangnamhae) were identified as the most vulnerable area.

• Journal of Korea Foundry Society
• /
• v.41 no.2
• /
• pp.127-131
• /
• 2021

Based on its good compatibility with high-temperature environments, the Ti-48Al-2Cr-2Nb alloy is used for high-temperature materials of industrial equipment. In this study, a Ti-48Al-2Cr-2Nb alloy turbocharger turbine wheel was fabricated by a vacuum centrifugal casting method. The conditions that prevent misrun defects of the turbocharger turbine wheel blade from centrifugal casting using alumina molds were investigated. The microstructure of the alloy prepared by vacuum centrifugal casting was studied by means of optical microscopy (OM), with a micro-Vickers hardness analyzer (HV), by X-ray diffraction (XRD) and by SEM-EDS. The HV and SEM-EDS examinations of the as-cast Ti-48Al-2Cr-2Nb alloy showed that the thickness of the oxide layer (α-case) was typically less than 50 ㎛. At a high preheating temperature of 1,100℃, a moderate RPM of 260, and with an alumina mold with a large gate size, there were almost no misrun defects. Therefore, it was confirmed that a Ti-48Al-2Cr-2Nb alloy turbocharger turbine wheel with fewer misrun defects could be achieved through a high preheating temperature, a moderate RPM, a large gate size and an alumina mold to suppress the formation of alpha-case components.

• Applied Chemistry for Engineering
• /
• v.22 no.4
• /
• pp.384-389
• /
• 2011

We made suspension of fumed silica in polyethylene glycol (PEG), studied rheological behavior as functions of contents of silica, dispersion condition, PEG molecular weight, temperature and contents of humidity. Rheological behavior of suspension was determined critical shear rate and rise of viscosity using rheometer AR2000. Suspension were PEGs of molecular weight 200, 400, and 600. Fumed silica suspensions of which silica contents are 5, 7, 9, 13, and 18% were prepared by normal mixing, homogenization and bead milling process. We observed their rheological behaviors at 10, 20, 30, and $40^{\circ}C$. As the PEG molecular weight and contents of silica increase, the critical shear rate was lowered. As the temperature increased, the critical shear rate was increased. Humidity contents of dispersion don't influence on the critical shear rate, but dispersion processes greatly affect the critical shear rate. The critical shear rate of suspensions prepared by the mixing process was the lowest, and that of suspensions prepared by the bead milling process was the highest. The rise in the shear viscosity of suspensions prepared by the mixing process is higher than that of suspensions prepared by the bead milling process. This was dependent on the dispersion condition of silica particle by dispersion process.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.5
• /
• pp.119-125
• /
• 2020

Research on high-attenuation concrete for the vibration reduction performance by mixing epoxy-based synthetic resins and aggregates is actively being conducted. The curing time of high-attenuation concrete is very short because water is not used, and the physical and dynamic properties are very excellent. therefore, it is expected to be widely used in building structures requiring reduction of interior-floor noise and vibration. Furthermore, A way to expand the applicability of the high-damping concrete mixed with polymer in the field of reinforcement material have been variously studied. In order to replace polymer concrete with ordirnary concrete and existing anti-vibration reinforcement material, it is necessary to review overall vibration reduction performance considering physical properties, dynamic properties, productivity and field applicability. In this study, the physical and dynamic properties of polymer concrete by epoxy mixing ratio compared with ordirnary concrete. As a result, the elastic modulus was similar. On the other hand, polymer concrete for the compressive, tensile, and flexural strengths was quite more excellent. In particular, the measured tensile strength of polymer concrete was 4-10 times higher than that of ordirnary concrete. it was a big difference, and the frequency response function and damping ratio was studied through modal test and finite element analysis model. The dynamic stiffness of polymer concrete was 20% greater than that of ordirnary concrete, and the damping ratio of polymer concrete was approximately 3 times more than that of ordirnary concrete.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.4
• /
• pp.601-609
• /
• 2022

Jack-up drilling rigs are mobile offshore platforms widely used in the offshore oil and gas exploration industry. These are independent, three-legged, self-elevating units with a cantilevered drilling facility for drilling and production. A typical jack-up rig includes a triangular hull, a tower derrick, a cantilever, a jackcase, living quarters and legs which comprise three-chord, open-truss, X-braced structure with a spudcan. Generally, jack-up rigs can only operate in water depths ranging from 130m to 170m. Recently, there has been an increasing demand for jack-up rigs for operating at deeper water levels and harsher environmental conditions such as waves, currents and wind loads. All static and dynamic loads are supported through legs in the jack-up mode. The most important issue by society is to secure the safety of the leg structure against collision that causes large instantaneous impact energy. In this study, nonlinear FE -analysis and verification of the requirement against collision for 35MJ recommended by DNV was performed using LS-Dyna software. The colliding ship used a 7,500ton of shore supply vessel, and five scenarios of collisions were selected. From the results, all conditions do not satisfy the class requirement of 35MJ. The loading conditions associated with chord collision are reasonable collision energy of 15M and brace collisions are 6MJ. Therefore, it can be confirmed that the identical collision criteria by DNV need to be modified based on collision scenarios and colliding members.