• Journal of the Korean Geotechnical Society
• /
• v.35 no.10
• /
• pp.47-66
• /
• 2019

A parametric numerical analysis according to diameter, length, and N values of soil was conducted for the PHC pile socketed into weathered rock through sandy soil layers. In the numerical analysis, the Mohr-Coulomb model was applied to PHC pile and soils, and the contacted phases among the pile-soil-cement paste were modeled as interfaces with a virtual thickness. The parametric numerical analyses for 10 kinds of pile diameters were executed to obtain the load-settlement relationship and the axial load distribution according to N-values. The load-settlement curves were obtained for each load such as total load, total skin friction, skin friction of the sandy soil layer, skin friction of the weathered rock layer and end bearing resistance of the weathered rock. As a result of analysis of various load levels from the load-settlement curves, the settlements corresponding to the inflection point of each curve were appeared as about 5~7% of each pile diameter and were estimated conservatively as 5% of each pile diameter. The load at the inflection point was defined as the mobilized bearing capacity ($Q_m$) and it was used in analyses of pile bearing capacity. And SRF was appeared above average 70%, irrespective of diameter, embedment length of pile and N value of sandy soil layer. Also, skin frictional resistance of sandy soil layers was evaluated above average 80% of total skin frictional resistance. These results can be used in calculating the bearing capacity of prebored PHC pile, and also be utilized in developing the bearing capacity prediction method and chart for the prebored PHC pile socketed into weathered rock through sandy soil layers.

• Journal of Korean Society of Transportation
• /
• v.22 no.3 s.74
• /
• pp.145-157
• /
• 2004

The cycle length design model of the Korean traffic responsive signal control systems is devised to vary a cycle length as a response to changes in traffic demand in real time by utilizing parameters specified by a system operator and such field information as degrees of saturation of through phases. Since no explicit guideline is provided to a system operator, the system tends to include ambiguity in terms of the system optimization. In addition, the cycle lengths produced by the existing model have yet been verified if they are comparable to the ones minimizing delay. This paper presents the studies conducted (1) to find shortcomings embedded in the existing model by comparing the cycle lengths produced by the model against the ones minimizing delay and (2) to propose a new direction to design a cycle length minimizing delay and excluding such operator oriented parameters. It was found from the study that the cycle lengths from the existing model fail to minimize delay and promote intersection operational conditions to be unsatisfied when traffic volume is low, due to the feature of the changed target operational volume-to-capacity ratio embedded in the model. The 64 different neural network based cycle length design models were developed based on simulation data surrogating field data. The CORSIM optimal cycle lengths minimizing delay were found through the COST software developed for the study. COST searches for the CORSIM optimal cycle length minimizing delay with a heuristic searching method, a hybrid genetic algorithm. Among 64 models, the best one producing cycle lengths close enough to the optimal was selected through statistical tests. It was found from the verification test that the best model designs a cycle length as similar pattern to the ones minimizing delay. The cycle lengths from the proposed model are comparable to the ones from TRANSYT-7F.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.3
• /
• pp.147-153
• /
• 2013

There exist various types of the WEC (Wave Energy Converter), and among them, the point absorber is the most popularly investigated type. However, it is difficult to find examples of systematically measured data analysis for the design of the point absorber type of power buoy in the world. The study investigates the wave load acting on the point absorber type resonance power buoy wave energy extraction system proposed by Kweon et al. (2010). This study analyzes the time series spectra with respect to the three-year wave data (2002.05.01~2005.03.29) measured using the pressure type wave gage at the seaside of north breakwater of Hupo harbor located in the east coast of the Korean peninsula. From the analysis results, it could be deduced that monthly wave period and wave height variations were apparent and that monthly wave powers were unevenly distributed annually. The average wave steepness of the usual wave was 0.01, lower than that of the wind wave range of 0.02-0.04. The mode of the average wave period has the value of 5.31 sec, while mode of the wave height of the applicable period has the value of 0.29 m. The occurrence probability of the peak period is a bi-modal type, with a mode value between 4.47 sec and 6.78 sec. The design wave period can be selected from the above four values of 0.01, 5.31, 4.47, 6.78. About 95% of measured wave heights are below 1 m. Through this study, it was found that a resonance power buoy system is necessary in coastal areas with low wave energy and that the optimal design for overcoming the uneven monthly distribution of wave power is a major task in the development of a WEF (Wave Energy Farm). Finding it impossible to express the average spectrum of the usual wave in terms of the standard spectrum equation, this study proposes a new spectrum equation with three parameters, with which basic data for the prediction of the power production using wave power buoy and the fatigue analysis of the system can be given.

• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.93-101
• /
• 2010

As the number of indispensable needs of clean energy increases due to the green new deal revolution, the possibility of heat energy harvesting from the surrounding infrastructures such as a railroad or highway was verified. In order to find more efficient usage of a heat source, the possibility of transforming heat into electricity were confirmed using Bi-Te type thermoelectric element, and electrical quality were tested with experiments of different heat source and environmental change in the surrounding infrastructures. After careful experiments, the possibility of collecting thermal energy and findings of the heat temperature change in infrastructrue are verified with a result of obtaining almost 20.82W in 70 celcius($^{\circ}C$) temperature differences and $1m^2$ surface area. Consequently, the ratio of heat temperatiure change and transforming surface area is the most crucial factor in the harvesting heat energy, and reducing thermal loss and improving thermal convection as well as transformation efficiency of thermoelectric element is required to get more efficient and durable generation.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.5
• /
• pp.543-551
• /
• 2006

Cold-formed steel studs that are being used as load-bearing members of wall panels for steel houses have a problem with their insulation due to the heat bridging of their web. Some additional thermal insulating materials should be used. To solve this problem, the new-concept hybrid stud, which consists of a galvanized steel sheet (t = 1.0 m - 12.0 m) and a GFRP panel (t = 4.0-6.0 mm), has recently been developed. An investigation on the structural behavior and the strength capacity of this new hybrid stud has been conducted so that it can be used in load-bearing wall panels of residential buildings. This paper describes the axial compression-torsion test results of the hybrid studs under both axial compression and torsion using ATTM. The main factors of the test were the stud length, the magnitude of the initial compressive force, and the loading method of the monotonic or cyclic loading. The torsion was applied increasingly while the initial compression was kept constant to the failure of the hybrid section. The advanced analysis results obtained form the finite element procedure that considered the material properties of the high-strength galvanized steel and the GFRP were compared with the test results for verification.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.15 no.5
• /
• pp.1-11
• /
• 2020

Increasing the number of unicorn startups has recently received much attention. In this study, we attempt to investigate that startups achieving an extremely high valuation could postpone their exit to raise more investment and receive more benefits. This study tested the hypotheses using data from Crunchbase, World Bank, Global Competitiveness Report, and Global Entrepreneurship Monitor. Using 140 unicorn startups that have already exited through an initial public offering (IPO) or mergers and acquisitions (M&A), we find out that unicorn startups tend to acquire higher valuation as their investment duration increases. Furthermore, we also examined the moderating effects of governmental policy and institutional distance from foreign investors in order to consider the institutional aspects of startups. The results of the moderating variables show significant supports. We expect to provide a better understanding with respect to making an exit decision of unicorn startups. Furthermore, managers and investors need to acknowledge the institutional factors of startups when they decide to fund.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.3 s.106
• /
• pp.249-258
• /
• 2006

In this letter, we propose a novel printed helix antenna for RFID reader in UHF band. The printed strip line of the antenna is first wound up outside a polygonal shaped layer and then the winding continues on an inner layer to control the overall gain and the radiation pattern. In addition, the winding pitch angles on each layer have either negative or positive values resulting in the broad CP bandwidth. The detail structure of the antenna was optimized using Pareto genetic algorithm(GA), so as to obtain excellent performances for RFID reader antennas. The optimized two-layered polygonal helix was fabricated on the cardboard of a flexible substrate and the performances were measured and compared with the simulations. The fabricated antenna was made up of copper tape which can adhere to a flexible cardboard and had 21.4 % matching bandwidth, 31.9 % CP bandwidth, readable range of $5.5m^2$ with kr=3.2. Also based on the current distribution of the strip line of the antenna and sensitivity of the antenna bents points, we confirmed that the antenna has the quarter-wave transformer near the feed for the broad matching bandwidth and radiates the traveling wave for the broad CP bandwidth using the bent strip line.

• Korean Journal of Environment and Ecology
• /
• v.31 no.5
• /
• pp.433-443
• /
• 2017

Securing the species compositional integrity (typicalness and representativeness) is the essential prerequisite for an integrated management of vegetation resources using the phytosociological $relev\acute{e}s$ and plant communities of the Z.-M. school. This study is intended to develop a tool for qualitative and quantitative evaluation of species compositional homotoneity of a set of $relev\acute{e}s$ per syntaxon. The new homotoneities, actual homotoneity ($H_{act}$), and optimal homotoneity ($H_{opt}$) taking into account the heterogeneous factors of $relev\acute{e}s$ are proposed. The correlations between the floristic variables such as the vegetation type, the new homotoneities, and the previously studied homogeneous measures (e.g. Pfeiffer's homogeneity, basic homotoneity-coefficient, corrected homotoneity-coefficient, and mean floristic similarity) are analyzed by using Spearman's rank correlation coefficient. $H_{act}$ and $H_{opt}$ are effective in determining the difference of inter-synthesized units and of inter-$relev\acute{e}s$, respectively. $H_{act}$ is the homotoneity that is the most independent of the number of $relev\acute{e}s$. On actual vegetation with long-term human impact in the Korean Peninsula, $H_{opt}$ has become an aid to the more precise understanding of $H_{act}$ as substantive homogeneousness of species composition of syntaxa. It is expected that $H_{act}$ and $H_{opt}$ can be used for the selection of a sort of homogeneous vegetation data to build a phytosociological $relev\acute{e}$-database with consistency and objectiveness for national vegetation resources.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.44 no.7
• /
• pp.1064-1071
• /
• 2015

Viscous fermented red ginseng extracts were dried and coated using a fluidized bed coater to increase convenience and consumer acceptance. The methods for making spherical granules of fermented red ginseng extracts with increasing convenience were established by using indigestible dextrin. Spherical granules of fermented red ginseng extracts with increasing convenience were made by mixing indigestible dextrin at 40% (40% IDD), 50% (50% IDD), and 60% (60% IDD) versus the soluble solid content of fermented red ginseng extracts. Spherical granules of fermented red ginseng extracts showed less angle of repose than powder of fermented red ginseng extracts. This means that spherical granules of fermented red ginseng extracts had good fluency with increased convenience. The more indigestible dextrin showed higher yields. Although 50% IDD showed less yield than 60% IDD, 50% IDD was the best mixing ratio for making spherical granules of fermented red ginseng extracts, as fermented red ginseng extracts is known as a healthy food. The optimized operation conditions of the fluidized bed coater for making 50% IDD were feeding rate 0.54 mL/min, atomization air pressure 2.15 bar, and product temperature $83.03^{\circ}C$.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.44 no.6
• /
• pp.921-927
• /
• 2015

The aim of this study was to investigate the effect of die temperature and repeated extrusion on physical properties of extruded white ginseng (EWG). The die temperature was adjusted to 100, 120, and $140^{\circ}C$, and extrusion was repeated under the same conditions with their corresponding samples. Specific mechanical energy input decreased as die temperature increased during extrusions. The secondary extruded white ginseng (SEWG) at a die temperature of $120^{\circ}C$ showed a higher expansion index than other extrudates. Elevation of both die temperature and repeated extrusion increased the specific length of extrudates. The highest apparent elastic modulus, breaking strength, and water solubility index obtained from SEWG at a die temperature of $100^{\circ}C$ were $7.53{\times}10^8N/m^2$, $7.49{\times}10^5N/m^2$, and 39.02%, respectively. When die temperature increased, water absorption index (WAI) decreased. The WAI of SEWG was higher than that of EWG. In conclusion, repeated extrusion affected physical properties of white ginseng and could be applied to produce improved quality of ginseng products.