• Journal of the Korean Chemical Society
• /
• v.43 no.2
• /
• pp.161-166
• /
• 1999

Transfer of lanthanide ions across the liquid/liquid interface facilitated by ionopore ETH4120 has been studied by using cyclic voltammetry (CV) and chronopotentiometry with cyclic linear current-scanning (CPCLCS) under the condition where the concentration of ETH4120 in nitrobenzene was much smaller than the concentration of lanthanide ions in aqueous solution. One cathodic current peak (transfer from aqueous to nitrobenzene phase) and two anodic current waves (transfer from nitrobenzene to aqueous phase) were observed. The cathodic wave was due to the formation of 1:1 (metal:ligand) complex and two anodic waves showed successive formation of 1:2 and 1:3 complexes in nitrobenzene solution. But there was no cathodic wave corresponding to two anodic waves. The ion transfer mechanism has also been discussed.

• Polymer(Korea)
• /
• v.31 no.4
• /
• pp.343-348
• /
• 2007

In this study, terpolymer of vinylidene fluoride (VDF), trifluoroethylene (TrFE), and chlorotrifluoroethylene (CTFE) were prepared by suspension polymerization using di-tertiary-butyl peroxide (DTBP) as an initiator. The structural characteristics including microstructure and chain conformation of the polymers have been carefully elucidated as a function of the chemical composition using NMR, FT-IR. The intensity of absorption bands of the $\beta$-phase gradually decreases and the $\gamma$-phase increases with the increment of CTFE mol%. The analysis results of DSC shows that the Curie phase transition temperature ($T_c$) of the terpolymer gradually shifts to ambient temperature and trace becomes smaller and broader with the increment of CTFE mol%. Also, activation energies of the samples were calculated by Freeman-Carroll method.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.6
• /
• pp.1136-1142
• /
• 2001

$Zn_xSr_{1-x}S$ thin films were prepared in the whole composition range by rf sputtering, using powder targets of a mixture of ZnS and SrS with the required mole fraction. The possibility of existence of $Zn_xSr_{1-x}S$ solid solutions was systematically investigated from the results of thin film growth, in terms of structural, optical characteristics and the chemical bonding of the constituent atoms. The XRD, XPS and optical results made it clear that the solid solutions with a single-phased zincblende structure and a single-phased rocksalt structure were formed at $0.86~0.93{\leq}x{\leq}1\;and\;0{\leq}x{\leq}0.29$, respectively. The miscibility gap, including phase separation regions was found to exist in $0.3{\leq}x{\leq}0.86~0.91$, in which lattice constants, binding energy and absorption edges kept almost constant by the same values as those at border compositions. The experimental results on phase transition agreed well with the fraction of ionic character fi based on the Phillips' dielectric theory.

• Applied Microscopy
• /
• v.31 no.4
• /
• pp.315-323
• /
• 2001

In situ TEM heating experiments utilizing kaolinite powder samples result in the following facts. (1) The water recirculation system adopted in the Gatan's heating holder is required to prevent specimen drift above $500^{\circ}C$. (2) Since the degree of phase changes depends on the thickness of powders below $600^{\circ}C$, examinations of both thin and thick specimens are required. (3) Sample preparation using Mo-grids is required for TEM heating experiments above $900^{\circ}C$. At these temperature ranges the effect of heating rate and holding time on the phase transition process increases drastically, so that a programmed temperature control is required. (4) TEM heating experiments of the embedded powders by epoxy for the cross-sectional view was limited due to the severe epoxy movement during heating above $300^{\circ}C$. Better methods of sample preparation are required to overcome this problem.

• Journal of Sensor Science and Technology
• /
• v.7 no.6
• /
• pp.386-393
• /
• 1998

We have carried out the measurements of complex dielectric constants with impedance/gain-phase analyzer using capacitor method and the experiments of high temperature X-ray powder diffraction with X-ray diffractometer using ${\theta}-2{\theta}$ scan method for the KTP single crystal which has the premium nonlinear optical properties. From the results of high temperature X-ray powder diffraction experiments, we have found that KTP does not undergo structural phase transition below $900^{\circ}C$. It is clear that KTP undergoes structural phase transition around $900^{\circ}C$ and belongs to orthorhombic above $900^{\circ}C$ still. However, we have applied phenomenological relation of dielectric relaxation to the results of complex dielectric measurement and have found that relaxation mechanism of KTP well satisfies the Cole-Cole relation over the temperature range from $-78^{\circ}C$ to $200^{\circ}C$. And also the relaxation time well satisfies the Vogel-Fulcher relation. It is regarded that the hopping and thermally activated diffusion mechanism may control the conduction behavior of KTP above $200^{\circ}C$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.3
• /
• pp.263-272
• /
• 1998

This paper presents the new control strategy that can minimizes the torque ripple by considering the magnetic nonlinearity and phase torque averlapping intervals, and describes the whole SRM drive system using proposed control method implemented by DSP(Digital Signal Processor). To do this, inductance and torque are, at first, measured according to the variation of rotor position angle while current is kept constant at predetermined several values. From these measured values, the entire inductance and torque for any current and rotor position are inferred by using neural network. And the waveform of the reference phase torque is determined for the torque ripple to be minimized considering the torque overlap between phases. The controller is designed for the actual torque obtained by the inferred torque look-up table using measured current and rotor position angle to track the predetermined reference phase torque by delta modulation technique. To perform a real time processing and ensure the reliability of the controller, DSP is implemented.

• Korean Journal of Cognitive Science
• /
• v.21 no.1
• /
• pp.77-93
• /
• 2010

The aim of this study was to identify neural correlates underlying the detection of faux pas, a test of theory of mind (ToM), in Korean healthy adults. Using functional magnetic resonance imaging, we compared the brain activities associated with faux pas stories and the activities associated with control stories. Faux pas stories compared with the control stories produced activations bilaterally in the superior frontal gyrus (BA 9) and in the precuneus (BA 7). The left medial frontal gyrus (BA 9), the left superior temporal gyrus (BA 38), the left inferior temporal gyrus (BA 20) and the right inferior parietal lobule (BA 40), the right postcentral gyrus (BA 1), the right lingual gyrus (BA 18), the right transverse temporal gyrus (BA 41) were also activated. The orbitofrontal cortex and the amygdala were not found to be involved in the detection of faux pas. This result suggests that brain activations associated with ToM are dependent on the type of mental state drawn by the task.

• Membrane Journal
• /
• v.25 no.1
• /
• pp.32-41
• /
• 2015

High performance polysulfone microfiltration membranes with a high were successfully prepared by vapor induced phase separation (VIPS) coupled with non-solvent induced phase separation (NIPS) process. Asymmetric Membranes were prepared with PSF/DMF/PVP/PEG/DMSO/water mixed solutions and water/IPA coagulant. PSF, DMF, PVP, PEG, DMSO, water was used as a membrane polymer, a solvent, a hydrophilic polymer additive, a polar protic liquid polymer, a polar aprotic nonsolvent, and a polar protic nonsolvent in the casting solution, respectively. The addition of polar aprotic nonsolvents, and polar protic nonsolvents is a convenient and effective method to control membrane structure. In order to control the morphology of polymeric membranes, the spontaneous emulsification induced by drawing water vapor into the exposed casting solution surface has been used. Control of the internal morphology of polymeric membranes by using mixed coagulation solution such as water and IPA is discussed in the present work. The pure water permeability, pore size distribution, surface hydrophilicity and membrane morphology were investigated. Due to the addition of DMSO to casting solution, the mean pore size increased almost $0.2{\mu}m$ and the water flux increased about 1000-1800 LMH.

• Membrane Journal
• /
• v.18 no.4
• /
• pp.317-324
• /
• 2008

Polysulfone membranes were prepared via the phase inversion process. With propionic acid as a nonsolvent additive, polysulfone casting solutions were solidified in an isopropanol bath. Propionic acid (PA) worked as a thermodynamic enhancer for phase separation and as a rheological suppressor for kinetic hindrance. Morphology of the prepared membranes significantly varied with propionic acid content in the casting solution. The dense skin layer, which was identified in the membrane prepared without PA, almost disappeared in the membrane prepared trom PA 10wt%. With 30wt% PA, the membrane revealed the morphological gradient from a nodular skin structure to a sponge-like substructure, including the finger-like cavity. Water permeability increased with PA content, and polyethylene glycol rejection decreased with the nonsolvent content.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.2
• /
• pp.91-97
• /
• 2018

Indium hydroxide powder was prepared by precipitation method. The reaction temperature ($150{\sim}250^{\circ}C$) and the holding time at each reaction temperature (1~72 h) were used as experimental variables. The particle size, microstructure and crystal phase of each prepared powder were observed through X-ray diffraction (XRD), Transmission electron microscope (FE-TEM) and BET. In this study, we investigated the phase and microstructural change induced by heat treatment of indium hydroxide nanoparticles at various temperatures for different holding times.