• Journal of Environmental Science International
• /
• v.7 no.6
• /
• pp.761-772
• /
• 1998

This study was performed to determine the optimum coagulant dosing amount for effective treatment of raw water. The removal rate of turbidity and the variations of water qualities according to various dosage of coagulants such as Alum, PAC and PACS were investigated. The optimum coagulant dosing amount to make the lowest turbidity of water were 35mg/ι t of Alum, 30mg/ι of PAC and 10mg/ι of PACS in case of 5 NTU of raw water turbidity, and 30mg/ι of Alum, 25mg/ι of PAC and 10mg/ι of PACS in case of 10 NTU of that, respectively. The removal rates of turbidity at 4 min. and 8 min. of settling time were 10 and 72% of Alum, 44 and 62% of PAC and 25 and 55% of PACS in case of 5 NTU, and 52 and 70% of Alum, 90 and 95% of PAC and 10 and 28% of PACS in case of 10 NTU, respectively. Judging from the settling capability of floc., the reaction time of floe. formation and removal efficiency of turbidity, PAC was evaluated as more effective coagulant than Alum and PACS. Also PAC was regarded as the most effective coagulant when the water supply was changed sharply and the fluctuation of the surface loading occured with wide and sharp in settling basin. pH and alkalinity of the water were decreased with increasing coagulants dosage. But pH and alkalinity were not decreased below 5.8 which is the standard for drinking water quality, and 10mg/ι which is the limit concentration of floc. breakage, respectively. Residual Al of the treated water was decreased with increasing coagulants dosage in case of 5 and 10NTU of raw water turbidity. $KMnO_4$ consumption of the water was decreased with increasing coagulants dosage. The reduction rate of $KMnO_4$ consumption at the optimum coagulants dosage were 39% of Alum. 18% of PAC and 11% of PACS in case of 5 NTU of raw water turbidity, and 42% of Alum, 27% of PAC and 36% of PACS in case of 10 NTU of that, respectively. Any relationship was not found between the removal rate of turbidity and KMnO$_4$ consumption. TOC of the water was a bit decreased with increasing coagulants dosage up to 30mg/ι but not changed above 30mg/ι of coagulants dosage. The degree of TOC reduction was increased in the order of Alum, PAC and PACS treatment. Zeta potential of the colloidal floe. at the optimum coagulants dosage was in the range of -20~-15mV in case of 5 NTU of raw water turbidity and 0~0.5mV in case of 10 NTU of that. respectively. Although the kinds and dosages of coagulants were different, zeta potential range were fixed under the conditions of the best coagulation efficiency.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.12
• /
• pp.863-870
• /
• 2012

The market trends of automatic meter reading associated with smart water meters were investigated. Also, recent developments and field applications of key technology for automatic meter reading associated with smart water meters were analyzed. Smart water meters have been manufactured mostly in United States and Europe and have been expanded their business to Asia. Integrated water management system combining with the additional functions such as real-time consumption metering, cost notification, water conservation, leak detection, water quality monitoring, and flow control have been operated in automatic meter reading. Both water quality and quantity data measured from smart water meters and sensors were transferred to data concentration units through neighborhood area network, and then were transferred to integrated server through wide area network. The data transfer methods were determined by comprehensively considering urban scale, density of smart water meters, power supply and network topologies. Common data collection methods such as fixed network to data concentation units, vehicles drive by, people walk by, and drone fly by have been applied. The automatic meter reading associated with smart water meters are spread throughout the world, and both water and energy savings result in saving the money and reducing the greenhouse gases emission.

• Korean Journal of Environmental Agriculture
• /
• v.21 no.3
• /
• pp.208-215
• /
• 2002

This study was carried out to evaluate the pollutant removal efficiencies of the advanced drinking water treatment using activated carbon process. for raw water, Nakdong river was used. from the activated carbon adsorption experiment the fellowing results were obtained The efficiency of water treatment enhanced with increase in empty bed contact time. Variation of pH was not detected to the bed depth, but DO content gradually decreased with the bed depth. Removal efficiency of $KMnO_4$ consumption, UV254 absorption, DOC and THMFP also were increased by increasing in the bed depth. Transition of adsorption zone from upper parts of the bed to the lower parts were detected as treatment periods increased. Large portion of DOCs were degraded and removed by the microbes growing on the surface of activated carbons. Cell numbers of microbes were estimated over $1.1\times10^7\;cell/cm^3$ at the depth of 20 cm from the surface 126 days after starting operation. The results shown that the activated carbon Inter was successfully acted as a biofilm filter.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.158-158
• /
• 2015

대부분의 대규모 배수지는 고지대에 위치함으로써 자연유하를 통해 배, 급수지역으로 용수를 공급한다. 이를 위해 배수지 전단에는 가압장이 위치하여 정수장에서 처리된 용수를 고지대에 위치한 배수지로 송수한다. 이때 가압장에서 발생하는 전력소비량이 매우 높은 것으로 알려져 있으며, 효율적인 펌프운영을 통해 상당한 전력비용 절감이 가능할 것으로 판단된다. 일반적인 가압장의 운영은 시스템 운영자의 경험을 토대로 해당 가압장에 연결된 배수지의 수위에 따라 펌프의 작동여부를 결정하는 방법이 주로 사용되고 있다. 이러한 운영방법은 용수공급의 안전성을 우선시함으로써 배수지의 수위를 일정하게 유지하고자 빈번하게 펌프를 작동하게 되고 따라서 가압장에서 소모되는 전력량이 커서 운영효율 측면에서는 바람직하지 않다고 할 수 있다. 또한 빈번한 펌프의 작동으로 인해 펌프의 수명이 단축될 뿐만 아니라, 배수지내 용수의 수질저하 문제도 발생할 수 있다. 본 연구에서는 효율적인 펌프장 운영을 위해 급수지역의 24시간 용수사용량을 예측하고, 그에 따른 펌프장의 가압 유량 및 양정을 파악하여 적정용량의 펌프를 선정하고 운영함으로써 펌프의 운영비용의 최소화 및 안정적인 용수공급을 동시에 달성하고자 한다. 이를 위해, 실시간 최적화 모형을 개발하였다. 개발된 최적화 모형은 상수관망해석 프로그램(EPAENT)을 연계하여 수요절점의 수압조건 및 운영상황을 모의하였다. 최적화 기법으로는 유전자알고리즘을 사용하였으며, 실제 시스템의 운영상황를 반영하기 위한 다양한 제약조건(operational constraints)을 적용하였다. 개발된 모형은 정속펌프(혹은 On/Off 펌프) 뿐만 아니라, 최근 실무에서 널리 사용되고 있는 변속펌프(variable speed pump)를 추가적으로 고려하였다. 개발된 모형은 국내에서 실제 운영되고 있는 송, 배수 시스템에 적용하여 모형의 실무 적용가능성을 검증하였다.

• Resources Recycling
• /
• v.32 no.2
• /
• pp.12-18
• /
• 2023

In 2018, the demand for silver (referred to as Ag) in the electrical and electronics sector was 249 million tons. The demand stood at 81 million tons in the solar module production sector. Currently, due to the rapid increase in solar module installation, the demand for silver is increasing drastically in Korea. However, Korea's natural metal resources and reserves are insufficient in comparison to their consumption, and the domestic silver ore self-sufficiency rate was as low as 2.2% as of 2021. This implies that a recycling technology is necessary to recover valuable metal resources contained in the waste plating solution generated in the metal industry. Therefore, this study compared and analyzed, the results of the impact evaluation through life cycle assessment according to an improvement in the process of recovery of valuable metals in the waste plating solution. The process improvement resulted in reducing GWP (Global Warming Potential) and ADP(Abiotic Depletion Potential) by 50% and 67%, respectively. The GWP of electricity and industrial water was reduced by 98% and 93%, respectively, which significantly contributed to the minimization of energy and water consumption. Thus, the improvement in recycling technology has a high potential to reduce chemical and energy use and improve resource productivity in the urban mining industry.

• Analytical Science and Technology
• /
• v.19 no.2
• /
• pp.181-187
• /
• 2006

This study was carried to survey the removal characteristics of BPA using coagulation process by PAC and PAHCS. BPA removal for PAC and PAHCS was 20.4 with 8.7 Al mg/L and 6.8 Al mg/L, respectively. Removal of BPA was lower than $UV_{254}$ and DOC but removal characteristics were similar. BPA removal for PAC and PAHCS was most high in pH 6.5 and 7.0 respectively. The time for removal by mixing time was 40 min in PAC and 30 min in PAHCS. When powdered activated carbon 50 mg/L was added in coagulation process, a high remove of BPA (61%) was noticed. Specially BPA was highly increase powdered activated carbon 5 mg/L alone. These results will be appliable in the conventional water treatment plants for improvement of water treatment system.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.18 no.6
• /
• pp.538-544
• /
• 1985

This study was carried cut to evaluate the water quality of spring waters in Pusan area(see Fig. 1). In this experiment, twenty-five water samples were collected from 5 stations from December 1983 to August 1984. Range and mean values of constituents of the samples are as follows: pH $5.80{\sim}7.25$, 6.60; water temperature $6.0{\sim}23.0^{\circ}C,\;12.9^{\circ}C$; total residue $33.0{\sim}325mg/l$, 121.2mg/l; alkalinity $4.75{\sim}51.6mg/l$, 24.1mg/l; hardness $9.47{\sim}85.0mg/l$, 30.3mg/l; electrical conductivity $0.495{\sim}2.750{\times}^2{mu}{\mho}/cm,\;1.239{\times}10^2{\mu}{\mho}/cm$;turbidity $0.54{\sim}7.80$NTU, 2.04NTU; $KMnO_4$ consumed $0.51{\sim}8.47mg/l$, 1.96mg/l; chloride ion $4.91{\sim}36.0mg/l$, 12.55mg/l; fluoride ion ND-0.30ppm, 0.08ppm; nitrate-nitrogen ND-8.94mg/l, 1.94m:g/l; nitrite-nirogen ND-0.10mg/l, 0.03mg/l; ammonia-nitrogen ND-0.16mg/l, 0.03mg/l: phosphate-phosphorus ND-0.09mg/l, 0.03mg/l; silicate-silicious $0.42{\sim}22.7ng/l$, 7.96mg/l; copper ND-10.5ppb, 2.46ppb; lead ND-22.7ppb, 3.54ppb; zinc ND-103ppb, 21.33ppb; iron $20.3{\sim}2,800ppb$, 801.72ppb, respectively. Arsenic, cyan, cadmium, manganese, mercury, chrome and phenol were not detected. Total residue, electrical conductivity, turbidity and chloride ion of station 1 (Milrakdong) were higher than others as 178.1mg/l, $2.127{\times}10^2{\mu}{\mho}/cm$, 3.16NTU and 16.32mg/l. The concentration of silicious had a great influence on precipitation. The concentration of fluoride ion of spring waters was lower as 0.08ppm than the criterion for drinking water as 1ppm, while iron was exceed 2.7 times as 801.72ppb.

• Journal of Food Hygiene and Safety
• /
• v.25 no.2
• /
• pp.153-161
• /
• 2010

The purpose of this study was to examine the appearance of norovirus in the water for food in food service institutions and the influence of physicochemical and microbial factors of norovirus in order to work out basic data to predict the detection of norovirus. Among 82 samples of water for food in food service institutions, norovirus appeared in 7 samples and the rate of appearance was 8.5%. As for the type of norovirus, one samples contained GI type (genotype GI-6) and six samples contained GII type (genotype GII-2, GII-4, GII-12). In the regression model of prediction of norovirus, the rate of appearance was correlated with $NH_3$-N, total solids and the consumption of $KMnO_4$, out of such variables as $NH_3$-N, total solids, the consumption of $KMnO_4$, depth, chloride and total colony counts, and its contribution rate for effectiveness was 78.60%. In order to examine the influential factor of environment upon the detection of norovirus, Pearson's correlation analysis was carried out. The predictable regression formula for appearance rate of norovirus was expressed as -1.818 + 42.677 [$NH_3$-N] + 0.023 [total solids] + 0.762 [consumption of $KMnO_4$] -0.009 [depth] -0.146 [chloride] + 0.007 [total colony counts] (R = 0.904, $R^2$ = 0.818, adjusted $R^2$ = 0.786, p < 0.05). The most influential factors upon the detection of norovirus were $NH_3$-N, total solids and the consumption of $KMnO_4$. In other words, when the measured values of $NH_3$-N, total solids and the consumption of $KMnO_4$ were higher, the possibility of appearance of norovirus increased.