• Journal of the Korea Institute of Military Science and Technology
• /
• v.3 no.2
• /
• pp.35-41
• /
• 2000

A modified theoretical analysis of the ballistic perforation on the double and multi-layered armour plates using an upper bound method has been presented in this paper. A modified model based on the suggestion of the Awerbuch-bodner model has been adapted and extended into double and multi-layered armour plates when the plugging type of penetration has been occurred. The residual projectile speed, ballistic limit velocity and contact time during the penetration process have been derived from the equation of motion at each stage.

• Archives of design research
• /
• v.18 no.4 s.62
• /
• pp.65-72
• /
• 2005

The expected demands for the new styling design can be studied by examining the recent deliveries and the new buildings on order. These ships are setting the trend for the operation of passenger ships. There has been a rapid increase in size and produce of ship some remarkable exterior design image. These ships follow very similar design concept, even if their operator compete with each other in the same market. But also new innovative design solution have been introduced to catch the interest of the passengers. The propose of this study is to investigate the exterior styling design in passenger ships, which result form examining the exterior elements such as funnels, pods, hulls, trademark, colours, flowing curvilinear lines and from. Each different passenger ship lines require different design style for different markets, while ships of different sizes and categories obviously require different solution. When a new class is created later, key design element will be retained, with some items being changed and new ideas introduced.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.1
• /
• pp.161-171
• /
• 2021

This paper presents the findings of a comparative study on minimum weight design and sensitivity evaluation using different experimental design methods for the structural design of an active-type deck support frame (DSF) developed for the float-over installation of an of shore plant topside. The thickness sizing variables of the structural members of a passive-type DSF were considered the design factors, and the output responses were defined using the weight and strength performances. The design of the experimental methods applied in the comparative study of the minimum weight design and the sensitivity evaluation were the orthogonal array design, Box- Behnken design, and Latin hypercube design. A response surface method was generated for each design of the experiment to evaluate the approximation performance of the design space exploration according to the experimental design, and the accuracy characteristics of the approximation were reviewed. Regarding the minimum weight design, the design results, such as numerical costs and weight minimization, of the experimental design for the best design case, were evaluated. The Box- Behnken design method showed the optimum design results for the structural design of the passive-type DSF.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.4
• /
• pp.225-234
• /
• 2022

The flow field measurement above whole area of the flight deck on 'Landing Platform Helicopter (LPH)' was performed by using PIV system in wind tunnel. In various heading angle conditions (0deg, -30deg, -45deg, -60deg, -75deg and ±90deg), the velocity fields such as U velocity & V velocity were measured at three different height above flight deck. Due to the geometrical characteristics of several bodies like deck, crane and super-structure, various vortex were generated. When the heading angle is 0deg, the deck edge vortex by flight deck and massive separation by super-structure were clearly observed by visualization with smoke and PIV, respectively. In other heading angles, the acceleration of flow in space between crane and super-structure were detected. And area with flow separation by super-structure is directly related to the heading angle of vessel.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.2
• /
• pp.8-8
• /
• 1987

This paper describes on the distribution of the vibration and the noise produced on a skipjack pole and line training ship M/S Pusan 403 (243GT, 1,000ps) under the cruising or drifting condition. The vibration and the noise level were measured by use of protable vibration analyzer (B and K 3513) and sound level meter (B and K 2205), and so the vibration level was converted into dB unit. The check points were set through every decks and around important places of the ship. The results obtained can be summarized as follows: 1. The vibration and the noise level 1) On the main deck, both the vibration and the noise level were highest at the vertically above the main engine, whereas the vibration level was the lowest in the bow store and the noise level beneath the bridge. 2) Under cruising condition, the vibration level around the cylinder head of main engine, port side of the engine room, on the shaft tunnel was 80, 67, 65 dB and the noise level 104, 87, 86 dB, respectively. 3) The vibration level on the vertical line passing through the bridge was the highest at the orlop deck with 60 dB and the lowest on the bridge deck with 55 dB, whereas the noise level the highest at the compass deck with 75 dB and the lowest at the orlop deck with 53 dB. 4) The vibration and the noise level on the open decks were the highest with 65 dB and 84 dB on the boat deck, whereas the vibration level was the lowest at the lecture room with 51 dB and the noise level the lowest at the fore castle deck with 57 dB. 5) On the orlop decks, both the vibration and the noise level were the highest at the engine room with 65 dB and 85 dB, and the lowest at bow store with 54 dB and 52 dB, respectively. Comparing with the vibration level and the noise level, the vibration level was higher than the noise level in the bow part and it was contrary in the stern part of the ship. 2. Vibration analysis 1) The vibration displacement and the vibration velocity were the greatest at the cylinder head of main engine with 100μm and 11mm/sec, and were the smallest at the compass deck with 3μm and 0.07mm/sec. They were also attenuated rapidly around the frequency of 100Hz and over. 2) The vibration acceleration was the greatest at the cylinder head with the main frequency of 1KHz and the acceleration of 1.1mm/sec super(2), and the smallest at the compass deck with 30KHz and 0.05mm/sec super(2).

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.2
• /
• pp.54-60
• /
• 1987

This paper describes on the distribution of the vibration and the noise produced on a skipjack pole and line training ship M/S Pusan 403 (243GT, 1,000ps) under the cruising or drifting condition. The vibration and the noise level were measured by use of protable vibration analyzer (B and K 3513) and sound level meter (B and K 2205), and so the vibration level was converted into dB unit. The check points were set through every decks and around important places of the ship. The results obtained can be summarized as follows: 1. The vibration and the noise level 1) On the main deck, both the vibration and the noise level were highest at the vertically above the main engine, whereas the vibration level was the lowest in the bow store and the noise level beneath the bridge. 2) Under cruising condition, the vibration level around the cylinder head of main engine, port side of the engine room, on the shaft tunnel was 80, 67, 65 dB and the noise level 104, 87, 86 dB, respectively. 3) The vibration level on the vertical line passing through the bridge was the highest at the orlop deck with 60 dB and the lowest on the bridge deck with 55 dB, whereas the noise level the highest at the compass deck with 75 dB and the lowest at the orlop deck with 53 dB. 4) The vibration and the noise level on the open decks were the highest with 65 dB and 84 dB on the boat deck, whereas the vibration level was the lowest at the lecture room with 51 dB and the noise level the lowest at the fore castle deck with 57 dB. 5) On the orlop decks, both the vibration and the noise level were the highest at the engine room with 65 dB and 85 dB, and the lowest at bow store with 54 dB and 52 dB, respectively. Comparing with the vibration level and the noise level, the vibration level was higher than the noise level in the bow part and it was contrary in the stern part of the ship. 2. Vibration analysis 1) The vibration displacement and the vibration velocity were the greatest at the cylinder head of main engine with 100$\mu$m and 11mm/sec, and were the smallest at the compass deck with 3$\mu$m and 0.07mm/sec. They were also attenuated rapidly around the frequency of 100Hz and over. 2) The vibration acceleration was the greatest at the cylinder head with the main frequency of 1KHz and the acceleration of 1.1mm/sec super(2), and the smallest at the compass deck with 30KHz and 0.05mm/sec super(2).

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2007.12a
• /
• pp.138-140
• /
• 2007

폰툰형 레저보트는 쌍동식 또는 삼동선식의 안전성이 확보된 선체와, 다양한 기능을 만족할 수 있는 상부구조로 구성, 건조비 뿐만 아니라 레저 접근성이 용이한 보트로서, 해양레저 선진국에서는 내수면뿐만 아니라 해수면에서도 함께 즐길 수 있는 가족형 레저보트로 인식되어 최근 보급이 확대되고 있는 추세이다. 그러나 폰툰형 레저보트는 최적의 공간활용을 위해 사각모양의 갑판형태로 인해 유체의 저항에 취약한 단점이 있다. 이로 인해 선저형상, 추진시스템 및 조향운전장치 뿐만아니라 선수선저부의 슬래밍 충격에 대비한 구조강도 등 체계적인 연구를 통한 개발이 필요하다. 이에 본 연구에서는 2가구 4인 가족단위로 함께 즐길 수 있는 안전성이 높고, 낚시, 스쿠버 둥을 위한 편의시설이 확보한 선형 최적형상 연구 및 구조강조 해석을 통한 9인승 규모의 폰툰형 레저보트를 개발하고자 한다.

• Journal of Navigation and Port Research
• /
• v.31 no.3 s.119
• /
• pp.223-228
• /
• 2007

In recent trends of the enlargement and specialization, container ship, LNCG, PCC and passenger ship which have relatively large hull and superstructure above the water line, are already being operated in the world It is very important information for the safety operation of these vessels to estimate the ship's performance under the specific wind condition while berthing, unberthing or low-speed sailing. In this paper, the effect of wind force and moment acting on the training ship HANNARA is investigated by using the numerical calculations. The results of drift angle and counter rudder angle with the relative wind direction and force, the critical wind velocity with the ratio of wind velocity and ship's speed and maximum heeling angle with the wind velocity are shown The presented results can be applied directly to T/S HANNARA in berthing maneuver and avoiding typhoons, and utilized as an educational materials.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.6
• /
• pp.541-549
• /
• 2012

The study adopted a freezing prevention method of the upper deck which used heating coil, and carried out numerical analysis by using ANSYS 13.0 CFD for design guide of the vessel operating in cold region. It is based on the experimental results of the anti-icing performance tests which were carried at cold room chamber in MOERI. Numerical analysis for the design guide was performed by considering S.S.T. (Shear Stress Transport) turbulent model for flow separation effects and the turbulence which occurred in interfaces of the numerical model in order to express appropriate heat transmission phenomenon. The numerical result shows average temperature of the upper deck surface appeared similarly compared with the indoor chamber test. The design guide for optimum freezing prevention presented through heat transmission capability and interval of the heat coil in various outdoor temperature($10^{\circ}C{\sim}-30^{\circ}C$) and wind speed(1m/s~7m/s).

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.482-487
• /
• 2007

The container mobilization of material resources has increased continually owing to international economy growth and overseas trade increase in recent years. There are large amounts of order received for container carriers which are the biggest in the world ranging from 8,000 TEU to 10,000 TEU or above The very large container carriers have minimum thickness of sheer strake, upper deck and hatch coaming about $65mm{\sim}90mm$. Therefore, this study is performed in order to develop vertical welding process with high deposition rates applicable to thick plate above 65mm thickness. Electrogas welding process with 1 pole and 2 poles has been developed to apply to vertical joint with thick plates in the shipyard. In this paper, it was explained that the relationship of cross section to various groove types and executed that electrogas welding for thick plates. The mechanical tests were carried out to verify the soundness and effectiveness of EGW.