• Journal of the Korean Wood Science and Technology
• /
• v.36 no.1
• /
• pp.69-78
• /
• 2008

Shearing strength test in tension type was investigated to determine the shear resistance of bolt and drift-pin connection of domestic larix glulam. The specimen was connected with bolt and drift-pin in the inserted plate type, and only bolt in the side plate type. The diameter of bolt and drift-pin used in the experiment are 12, 16 and 20 mm. The hole of bolt was drilled at the end-distance 5 d and 7 d. Tension load was loaded in the direction parallel to grain. The shear resistance was evaluated according to end-distance through this, the yield load was compared with the experimental yield load, using Larsen's formula. The prototype design strength is based on the yield load of end-distance 7 d and the reduction factor of end-distance 5 d was calculated. The results were as follows. 1. The average of maximum load of drift-pin connection was higher by 3~30% at the inserted type than at bolt connection with increasing diameter. In bolt connection, the average of maximum load of the side type was 1.54~2.07 times higher than that of the inserted type. In the same diameter, the average of maximum load of end-distance 7 d was higher by 8~44% than that of 5 d. 2. The bearing stress was 1.16~1.41 times higher at the inserted connection than at drift-pin connection, and 1.37~1.86 times higher at 7 d than at 5 d. Also, when the slenderness ratio was below 7.5 at drift-pin connection and below 6.0 at inserted connection, the lateral capacity was good. 3. The ratio of the experimental yield load and the predicted yield load calculated by Larsen's formula proposed by Larsen was 0.80~1.10 at inserted connection, and 0.75~1.46 at side connection. 4. When the inserted bolt connection was based on the yield load of end-distance 7 d, the reduction factor was 0.89 at 12 mm connection, 0.93 at 16 mm and 0.85 at 20 mm. The reduction factor was 0.89 at 12 mm the inserted drift-pin connection, 0.93 at 16 mm, 0.93 at 20 mm. The reduction factor was 0.79 at the side connection of the 12 mm bolt connection and 0.80 at 16 mm.

• Composites Research
• /
• v.12 no.3
• /
• pp.45-54
• /
• 1999

In this paper, an experimental study on the buckling and postbuckling control of a laminated composite beam with eccentrically embedded SMA wire actuators is performed. For the purpose of enhancing the critical buckling load, buckling control is investigated through the use of reactive moment associated with the shape recovery force of SMA wire actuators. To improve the control authority for the buckling and postbuckling control of the SMA-composite beam, closed-loop control is used. The buckling and postbuckling control behaviours are presented and discussed qualitatively and quantitatively on loaddeflection plots considering the stacking sequence of the laminate, slenderness ratio of the beam and activation conditions of the SMA wire actuators. By maintaining the desired deflection shape with the proper reactive moment, buckling control can be extended to the postbuckling of the SMA-composite beam subjected to an external load.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.956-959
• /
• 2007

기존 투명방음판용 알루미늄 프레임의 구조적 단점을 보완할 수 있는 강재-FRP(Fiber Reinforced Plastic) 합성단면 구조재를 개발하였으며, 아울러 조립이 간편하고 외부 충격에 의해 쉽게 분리가 되지 않는 삽입형 수평재-수직재 코너연결부 상세를 개발하였다. 개발된 강재-FRP 합성단면 구조재와 코너연결재를 결합하여 프레임을 형성하고 그 사이에 투명패널을 삽입함으로써 길이 4m, 높이 1m 투명방음판 시작품을 완성하였으며, 이렇게 완성된 투명방음판 시작품을 대상으로 KS 4770-1 구조성능 평가시험을 수행하였다. 한국도로공사 교량부 시험하중에 대해 설계된 강재-FRP 합성단면 프레임 투명방음판의 구조성능 평가결과, FRP 의 추가적인 구조강성 증가 효과로 인해 한국도로공사 교량부 시험하중을 약간 상회하는 KS 2 호 등급시험하중까지도 만족시키고 있음을 확인할 수 있었다.

• The Journal of Korean Academy of Prosthodontics
• /
• v.25 no.1
• /
• pp.281-302
• /
• 1987

의치상 재료 종류에 따라 의치, 점막 및 하악골에 발생되는 변위 및 응력을 연구하기 위하여 컴퓨터를 이용한 수치적 해석인 2차원 유한 요소법을 이용하였다. 2차원 유한 요소 모형으로선 표준 크기의 하악골 및 의치를 고려하여 231개의 사변형 요소 및 268개의 절점으로 분할한 후 각 구성 성분의 물리적 성질인 탄성률 및 프와송비를 대입시켰다. 사용된 의치로서는 일반 합성수지의치, 2mm후경의 탄성재를 의치상 하부에 이장한 합성수지의치, 2mm후경의 탄성재를 치아와 의치상 중앙에 삽입한 합성수지의치 및 0.5mm후경의 금속상의치의 4종류였으며, 하중시에 하악의 고정 부위로선 생체와 동일 조건을 부여하기 위하여 교근, 내측익돌근, 측두근등의 하악 폐구근이 부착되는 하악각 부위 및 하악 근돌기 부위의 16절점을 고정점으로 하였다. 하중 조건으로선 하악 제1대구치의 일점에 10kg의 수직 집중하중, 하악 중절치의 일점에 7kg의 수직 집중하중 및 하악 제 1소구치로 부터 하악 제2대구치까지의 교합면에 10kg의 수직 분산하중을 부여하여 분석한 결과는 다음과 같다. 1. 하중이 의치 교합면위의 가해진 부위에 따라 다양한 의치 회전 및 강하 현상을 보였으며, 탄성재를 이장 및 삽입한 합성 수지 의치의 변위가 일반 합성수지의치 및 금속상 의치의 변위보다 더 컸다. 2. 주응력을 고려할때 점막 부위에는 주로 압축 응력이 작용하였으며 치조제 부위는 압축응력과 인장 응력이 함께 작용하였다. 3. 탄성재를 삽입한 합성수지의치에 최고 등가 응력이 집중되었으며 그 다음은 탄성재를 이장한 합성수지의치, 일반 합성수지의치의 순이였으며 금속상의 경우는 금속을 따라서 높은 등가 응력이 넓게 분산되었다. 4. 의치상 종류에 관계없이 동일 하중 조건하에선 점막에 나타나는 등가 응력의 크기 및 분산양태는 유사하였다. 5. 하악골에서 등가 응력은 의치지지 부위에만 국한되지 않고 넓게 분산 되었으며 의치상 종류 및 하중 조건에 관계없이 치조제 후방 및 하악연의 후방 부위에 특히 높은 등가응력이 집중되었다. 6. 하악 중절치의 일점에 수직 하중을 가한 경우가 다른 하중 조건에 비하여 지지점과의 거리차이로 인하여 하악골에 가장 높은 등가 응력을 유발하였다. 7. 의치상 재료에 따른 하악 골에 발생되는 응력의 크기 및 분산에는 큰 차이가 없으나 금속상의 경우가 교합압을 분산하는데는 효과적이었다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.2
• /
• pp.183-190
• /
• 1982

이 논문에서는 유압제어장치의 응답에 대하여 관성하중, 점성하중, 쿨룸(Coulomb)마찰 및 입력 신호의 주파수가 시스템에 미치는 영향을 고찰하였고, 이에 따른 속도와 압력파형을 주로 서 술하였다. 피스톤의 드리프트(drift)와 스프링하중을 제외한 대부분의 요소가 고려되었다. 추출된 방정식은 모두 무차원화 하였으며 입력 신호를 계단함수로 할 때에는 위치 피이드백 (feedback)이 삽입되었다.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.4
• /
• pp.1-8
• /
• 2001

This study was carried out to investigate the strength and stiffness of drift pinned and bolted joints with steel-plates by the tension-type lateral strength tests. Specimens were solid wood of Pinus densiflora. Bolt and drift pin were jointed with inserted steel plates. Tests were conducted with combinations of two loading directions (parallel to the grain : 0 degree, perpendicular to the grain : 90 degree) and three diameters of fasteners (d = 6 mm, 10 mm, 12 mm). The results obtained were as follow: 1. In the test of the parallel to the grain, maximum loads were increased with increasing of the diameter of bolt and drift pin in the same end distance. In the test of perpendicular to the grain with diameter 10 mm and 12 mm, specimens mostly were failed with horizontal splits in woods reaching the yield load of drift pinned and bolted joints. 2. The ratio of maximum load to the yield load determined by the so-called "5% offset method", was great in bolted joints in the parallel to the grain This trend become more remarkable as the slenderness ratio was increased. 3. The calculated yield strength was agreed well with the experimental results of drift pinned joint(0 degree).

• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.117-122
• /
• 2008

Acoustic test was performed to verify the ability of KSLV-I PLF acoustic protection system (Acoustic blanket) to reduce the acoustic load. The test results showed that the acoustic protection system has +3 dB safety margin compared with design requirement. This paper also illustrates the increase of insertion loss by the acoustic protection system by comparing that of the bare PLF structure.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.6
• /
• pp.1-10
• /
• 2001

In this study, the horizontal loading tests of 10ton and 200ton capacity of LRB(lead-rubber bearing) were performed for the evaluation of the dynamic properties of the LRB. It is noted from the test results that dynamic properties of the LRB are dependent on the loading frequency, vertical load and shear strain. A Slender bearing subjected to large deformation will tend to develop plastic hinges in the end regions of the lead plug which will cause the failure of the lead plug. It is recommended that the appropriate mechanical properties of LRB considering the level of structural response and input ground motion should be used in the design of base isolated structures.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.6 s.134
• /
• pp.31-37
• /
• 2005

This research investigated the increase in strength capacity for the difference of various connection conditions. Connections were constructed with a main member, glulam and side members, 3 mm steel plates. Connections were varied in the number of inserted 1 mm steel plate. The strength capacity considerably increased by inserting the very thin steel plate within structural glulam connection. Glulam connections were classified as the number of inserted steel plate, group A was none, group B was one, group C was two, and group D was three. Ultimate and design values of the group B were 18% and 13% greater than the group A, the group C were 27% and 20% than the group A, and the group D were 33% and 24% than the group A. However, the increase in strength capacity and the additional difficulty should be considered on economic and technical view.

• Composites Research
• /
• v.29 no.2
• /
• pp.60-65
• /
• 2016

In this paper, finite element analysis and real time monitoring experimental work using FBG sensor were carried out for analyzing structural integrity of a Type IV hydrogen pressure vessel under impact loading condition. By using finite element analysis with the ply based modeling technique, sensor insertion points and pressure condition were suggested. Tensile test with an angle ply specimen was conducted for getting the reliability of FBG sensor insertion method. After fabricating the vessel, total five times pressurization fatigue tests were conducted (Non-impact pressurization: 1, After impact pressurization: 4). Experimental results revealed that filling cycle time was gradually increased and filling gradient was decreased when the vessel experienced impact.