• Journal of the Korean Geotechnical Society
• /
• v.24 no.6
• /
• pp.57-67
• /
• 2008

Two test methods, nonrepetitive plate loading test (NPLT) and repetitive plate loading test (RPLT) are being used to control the quality of compaction through the evaluation of the stiffness of subgrade soils in the Korea railway industry. Subgrade reaction modulus ($k_{30}$) from the NPLT and strain modulus ($E_v$) from the RPLT are the index values to check them. The methods have similar aspects, but they differ in the modulus evaluation method, the numbers of loading stage, termination procedures, etc. This paper analyses the differences of the two test methods and evaluates the relationship between subgrade reaction modulus and strain modulus. In order to develop the relationship, total 22 tests were performed including the NPLT and the RPLT at the 6 original grounds, and 5 upper or lower subgrades in Kyungbu High Speed Railway II stage construction sites. According to the soil conditions, the relationship between subgrade reaction modulus and strain modulus was proposed with corrections by considering strain states, mean confining pressures, and Poisson's ratio.

• International Journal of Highway Engineering
• /
• v.4 no.2 s.12
• /
• pp.33-42
• /
• 2002

The cracks in the pavements result from drying shrinkage, temperature change, repeated traffic loadings and so on. The reduction of soil support, spatting and many local failures are caused by water and incompressible foreign materials infiltrated into the cracks. In order to reduce this kind of problems the crack width must be controlled and managed by the accurate measurement. The current method is a visual survey using a microscope, which requires traffic blocking. The purpose of this study is to find the best condition to measure accurate crack width using automated pavement condition survey equipment running at the similar speed as other vehicles. In this study pavement surfaces are filmed on an enlarged scale by the camera with a zoom lens, and then the proper focal distance is determined according to the crack width through a pilot survey. The conditions for measurement of the accurate crack width using the image processing technique are suggested by comparing crack widths surveyed using a microscope in the field with those computed by various factors in the image processing program, STADI-2. In conclusion, the camera with a focal distance of 75m could detect crack range of 0.5mm$\sim$1.2mm In width with an accuracy of 80% for CRCP. The camera with a focal distance of 12.5mm could detect crack range of 1.8mm$\sim$3.3mm in width with an accuracy of 90% for asphalt pavement.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.11
• /
• pp.1381-1389
• /
• 2012

The object of this study considers corrosion fatigue improvement of 7075-T6 aluminum by using shot peening treatment on 3.5% NaCl solution at room temperature. Aluminum alloy is generally used in aerospace structural components because of the light weight and high strength characteristics. Many studies have shown that an aluminum alloy can be approximately 50% lighter than other materials. Mostly, corrosion leads to earlier fatigue crack propagation under tensile conditions and severely reduces the life of structures. Therefore, the technique to improve material resistance to corrosion fatigue is required. Shot peening technology is widely used to improve fatigue life and other mechanical properties by induced compressive residual stress. Even the roughness of treated surface causes pitting corrosion, the compressive residual stress, which is induced under the surface layer of material by shot peening, suppresses the corrosion and increases the corrosion resistance. The experimental results for shot peened specimens were compared with previous work for non treated aluminum alloy. The results show that the shot peening treatment affects the corrosion fatigue improvement of aluminum alloys and the induced compressive residual stress by shot peening treatment improves the resistance to corrosion fatigue.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.688-695
• /
• 2017

Compared to metal, CFRP has excellent mechanical characteristics in terms of intensity, hardness, and heat resistance as well as its light weight that it is used widely in various fields. Therefore, this material has been used recently in the aerospace field. On the other hand, the material has shortcomings in terms of its extreme vulnerability to damage occurring internally from an external impact. This study examined the intensity up to its destruction from repeated use with the internal impact of a CFRP laminated plate that had also been exposed to external impact obtain design data for the external plate of aircraft used in the aerospace field. For the experimental method, regarding the quasi-isotopic type CFRP specimen and orthotropic CFRP specimen that are produced with a different layer structure, steel spheres with a diameter of 5 mm were collided to observe the resulting impact damage. Through a 3-point flexural fatigue experiment, the progress of internal layer separation and impact damage was observed. Measurements of the flexural fatigue strength after the flexural fatigue experiment until internal damage occurs and the surface impacted by the steel spheres revealed the quasi-isotopic layer structure to have a higher intensity for both cases.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.430-439
• /
• 2002

The development of reinforcing steel is required in reinforced concrete structures. The standard hooks that have been widely used for the tensile development in the beam-column joints tend to create difficulties of construction such as steel congestion as the member cross sections are becoming smaller due to the use of higher strength concrete and higher grade steel. Using the reinforcing bars with end mechanical anchoring device (headed reinforcement) provides potential economies in construction such as reduction in development lengths, simplified details, and improved responses to cyclic loadings. In this paper, the pullout strengths and behaviors of the headed reinforcement were experimentally studied. In 33 pullout tests performed using D25 deformed reinforcing bars, the test parameters were embedment depth, edge distance, head size, and the use of transverse reinforcement. The pullout strengths determined from tests closely agreed with the pullout strengths predicted using the CCD method. The pullout strengths increased with increasing embedment depths nd edge distances. The strengths tend to increase with the use of larger heads. From the experimental program where the effect of the transverse reinforcement was examined, a modification factor to the CCD was suggested to represent the effect of such reinforcement that is installed across the concrete failure plane on the pullout strengths.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.313-316
• /
• 2008

Corrosion of steel in the reinforced concrete structures is one of the main reason of degradation. It causes that lifetime of structures is shortened and maintenance cost is increased. And it also causes degradation of structures like bridges which are under repeated load. So, many research have been performed about FRP rebar. But there are few research about FRP rebar under fatigue. This study is to examine flexural characteristic of concrete beam reinforced with FRP(CFRP, GFRP) rebar under static and fatigue for considering the application. The specimens that used in this study are designed by ACI 440.1R-06 and reinforced with CFRP(CR) or GFRP(GR) overly. In the result of static bending test, all specimens were failed at compression phase. In fatigue test, the fatigue stress level was 60%, 70% or 80% of the static bending strength. Most of the specimens seemed to be compressive failure, but CR-60 and CR-70 specimens were failed with rupturing of tension bar.

• Journal of Korea Foundry Society
• /
• v.43 no.3
• /
• pp.107-136
• /
• 2023

Natural silica sand was commonly used for sand casting of cast steel products, and chromites sand was used to suppress seizure defects due to the lack of thermal properties of silica sand. However there are disadvantages such as deterioration by repeated use, system sand mixing problem, difficulty separating and removing, increased during mold according to high density and to being waste containing chrome. Recently, industrial waste reduction and atmospheric environment improvement have been highlighted as important tasks in the casting industry. In order to solve the problems that occur when using foundry Sand and to improve the environment of casting factories, various artificial sands that can be applied instead of natural silica sand have been developed and introduced. Artificial sands can be classified into artificial sand manufactured by the electric arc atomization or gas flame atomization, artificial sand manufactured by the spray drying & sintering process, artificial sand manufactured by the sintering & crushing process and exhibit different physical properties depending on the type of raw-minerals and manufacturing method. In this study, comparative evaluation tests were conducted on the physical properties of various foundry sands, mold strength, physical durability, thermal durability, and casting test pieces. When comprehensively considering the actual amount of molding sand used according to density, the mold strength according to the shape of sand, the physical and thermal durability of foundry sand, and the heat resistance characteristics of foundry sand, 'Molten artificial sand A1' or 'Molten artificial sand B' is judged to be the most suitable spherical artificial sand for casting of heavy steel castings.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.8
• /
• pp.1035-1041
• /
• 2013

To evaluate the structural integrity and dynamic characteristic of the knuckle part of a KTX anti-roll bar, an experimental and a numerical approach were used in this study. In the experimental approach, the acceleration and strain data for the knuckle parts of the KTX and KTX-SANCHUN anti-roll bar were respectively measured to evaluate and compare its structural dynamic characteristics under the operating environments of the Honam line. In the numerical approach, the evaluation of its structural integrity was conducted using LS-DYNA 3D, and then, the reliability of the finite element model used was ensured by a comparative evaluation with the experiment. The numerical results showed that the stress and velocity field of the knuckle part composed of a layered structure of a thin steel plate and rubber were more moderate than those of the knuckle part made of only a thick steel block owing to the reduction of relative contact between the knuckle and the connecting rod. It was found that the knuckle part made of a thin steel plate and rubber was recommended as the best solution to improve its structural integrity resulting from the elastic behavior of the KTX anti-roll bar being enabled under a repeating external force.

• Journal of the Korea Concrete Institute
• /
• v.25 no.4
• /
• pp.419-428
• /
• 2013

In this study, experimental research was carried out to evaluate the constructability and seismic performance of high strength R/C exterior beam-column joints regions, with or without the shear reinforcement, using high ductile fiber-reinforced mortar. Five specimens of retrofitted the exterior beam-column joint regions using high ductile fiber-reinforced mortar are constructed and tested for their retrofit performances. Specimens designed by retrofitting the exterior beam-column joint regions (BCJNSP series) of existing reinforced concrete building showed a stable mode of failure and an increased its maximum load-carrying capacity by 1.09~2.03 times in comparison with specimen of BCJNS due to the effect of enhancing dispersion of crack control at the time of initial loading and bridging of fiber from retrofitting new high ductile materials during testing. Specimens of BCJNSP series attained its maximum load carrying capacity by 0.92~0.96 times and increased its energy dissipation capacity by 1.62 times when compared to standard specimen of BCJC with a displacement ductility of 4.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.59-59
• /
• 2017

무인 헬리콥터의 양력을 개선하기 위한 익형 설계 단계로서 두꺼운 익형(V1505A)과 얇고 처진 익형(V2008B)의 기본 두 익형의 특성을 예측하는데 있어 회전하는 블레이드의 현실적 조건을 반영한 3D 모델을 마련하고 성능을 예측하였다. Fluent를 이용한 400 mm 선형모델의 시뮬레이션에서는 V1505A 익형은 높은 받음각에서 안정적인 특성을 보인 반면 V2008B는 비교적 높은 동력효율 특성을 보였으나, 높은 받음각에서는 실속 이후 양력이 급락하는 특성을 나타낸다. 형성된 노드 수는 약 870,000개로 하였다. 시위길이 135 mm인 익형 V2008B의 형상은 ANSYS (Fluent v16.2)를 이용해 반경(길이) 1,502 (1,380) mm 의 로터 블레이드를 구성하였다. 충분하지 않은 유동장이 익형 표면에서의 유동의 영향에 영향을 주지 않도록 직경 20 m의 원방경계(far field)를 형성하였다. 사용된 매쉬의 형태는 정사면체 형태로 로터 표면으로부터의 첫 번째 두께 높이는 0.001 m이고 10개의 층으로 형성하였다. 정지 비행하는 헬리콥터의 상태를 가정하여 회전좌표계를 이용하여 정상상태의 유동을 해석하고 사용된 난류모델은 넓은 영역에서의 유동을 고려하여 Realizable $k-{\varepsilon}$ 모델을 사용하였다. 내측그립 받음각 $6{\sim}22^{\circ}$에 대하여 현실적인 회전속도를 연동하여 600~1000 rpm을 적용하였다. 반복수(iteration)는 2000으로 하여 잔차값(residual)이 충분히 수렴하도록 하였다. 전체적으로 실제 헬리콥터가 발휘하는 양력보다는 낮은 수치로 예측되었으며 모델 및 해석 조건에 대한 검토가 필요해 보인다. 양력 값은 받음각 $10^{\circ}$에서 자중(약 68 kgf)을 극복하였고 받음각 $12^{\circ}$에 유상하중 20 kgf을 발휘하며 888 N의 양력을 보였다, 이어 받음각 $22^{\circ}$에서 실속 현상이 발생하였다. 받음각이 증가함에 따라 항력 역시 증가하였으며 받음각 $12^{\circ}$에서 121 N이었고 실속에 이르며 항력은 갑자기 증가할 것으로 예측된다. 본 연구는 변이 익형 개발의 선행 단계로 기본 익형에 대한 공력특성을 CFD 시뮬레이션을 통하여 예측하였다. 예측 값은 현실적 실험방법을 통하여 검증이 되어야 하며 이후 변이익형에 대한 예측과 설계가 가능하다.