• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.11
• /
• pp.983-990
• /
• 2011

This paper investigates active noise control(ANC) of a rectangular cavity using single channel filtered-x least mean square(FXLMS) algorithms to globally reduce the interior noise. To obtain the global reduction of the interior noise, multichannel active control should be incorporated in general. We, however, examined firstly the optimal location of the secondary source that produces a global reduction of the interior noise field using single channel control. We then investigated the frequency characteristics of the reduction to yield the effective frequency band of the active control system. It follows that the secondary source should be located as close to the primary source as possible in order to obtain the global reduction.

• Proceedings of the Korean Statistical Society Conference
• /
• 2003.05a
• /
• pp.207-212
• /
• 2003

21세기 정보화, 기술, 국제화 등 시대적 성격에서 볼 때 국가적 차원의 통계적 소양 교육은 일반 시민의 기본 소양 및 인적자원 개발의 문제임을 인식하고 국가 그리고 대학의 일반 교육 정책으로 다를 필요가 있다. 현재 대학 교육에서 소외되고 사각지대에 있는 기초통계학 교육을 사회 변화와 요구를 반영할 수 있는 교육이 시급한 과제이다. 본 논문은 대학 기초통계학의 현재의 대학교육 상황, 학생들의 교육적 배경, 통계적 소양과 시대적 의미, 기초통계학의 목표, 성격 그리고 방향들을 제시하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.1-9
• /
• 1998

In this study, we have investigated the preparation conditions of 45$\times$45$\times$20(mm) square cross-section sapphire single crystal by the modified heat exchanger method using water as a coolant. Melting and solidification processes were optimized by the systematic change of the chamber pressure with the heater temperature. As a results, solidification temperature was between 1960 and $1970^{\circ}C$. The crucible was formed by handling. Therefore its shape should had the 'spiral type' ear at edge of its side. Heat exchanger affected to the temperature distribution and gradient of molten alumina. Heat flux and unmelted seed were controlled by volume of heat exchanger. Voids were controlled by the cooling rate of the heater below $0.2^{\circ}C$/min.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_2
• /
• pp.961-968
• /
• 2022

Hydrogen embrittlement leads to the damages in bolts, nut, especially, high pressure valves, in the semiconductor facilities, hydrogen vehicles, hydrogen stations and so on. Monel material has higher strength than SUS material. Therefore, even though Monel material with special alloy is usually used to prevent the hydrogen embrittlement, it needs powerful drawing system to manufacture the rectangular or hexagonal bar using circular bar. The purpose of this study is to investigate the characteristics of plastic deformation of Monel material and 2 rollers of rolling unit in plastic limit through numerical analysis. As the results, it was predicted that, based on mean stress, as the rolling step was increased, the rolling force of rolling unit was decreased. In addition, the heat treatment for Monel material was needed because of residual stress due to plastic deformation. As for rollers, the roller was safe about 1.86 times compared with that of ultimate strength. In this study, as the roller 2 showed larger stress than roller 1, thus, roller 2 should be designed carefully to guarantee the safety. Further it was confirmed that the reaction force of roller could be helpful in bearing design.

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.3
• /
• pp.573-580
• /
• 2024

Recently, the special alloy, for instance, such as Monel and Inconel, is used for valves, bolt/nuts, and fittings in semiconductor facility, FCEV(fuel cell electric vehicle) and hydrogen gas station, to reduce the hydrogen embrittlement. Even though the Monel material has high cost, it is recommended to use for the cases of ultra high pressure, ultra high leak-proof and so on. The purpose of this study is to investigate the characteristics of Monel material within elastic limit through the comparative analysis when Monel material is extruded or drawn. As the results, the deformation of Monel material was increased as the number of pass was increased, further, the deformation of Monel material by drawing was larger than that by extrusion. In the safety factor, the case that load is less than 420kN, the plastic deformation due to drawing could be happened faster than that due to extrusion. However, the case of more than 420kN, it showed that the plastic deformation for extrusion and drawing was almost similar.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.691-694
• /
• 2009

전세계적으로 운전자의 주행시 차선변경이나 정지시 돌발적으로 지나가는 옆차선의 차량을 감시함으로서 교통사고발생율을 대폭 감소시킬 수 있기 때문에 많은 시스템들이 개발되고 있다. 그러나 대부분 비젼시스템과 연결되는 고정형 타입으로서 운전자의 시각을 지원해 주는 경우가 많았다. 본 연구에서는 회전형으로 제작되어 사용자가 원하는 대로 감시영역을 축소시키거나 확대시킬 수 있는 방식으로서 사각지대 감지를 위한 서보모터의 회전속도/각도와 초음파센서의 측정거리 및 LED의 ON-OFF 등 각종 파라미터를 조절함으로서 최적의 사양을 선정하였고 시험을 통해 그 타당성을 증명하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.247-249
• /
• 2009

This paper investigates active noise control(ANC) of a rectangular cavity using single channel filtered-x least mean square(FXLMS) algorithms to reduce interior noise globally. To obtain global reduction of the interior noise, multichannel active control should be incorporated in general. We, however, examined firstly the optimal location of the secondary speaker that produces a global reduction of the interior noise field. We then investigated the frequency characteristics of the reduction to yield the effective frequency band of the active control system. It follows that the secondary speaker should be located as close to the primary source as possible in order to obtain global reduction.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1434-1437
• /
• 2003

Sometimes open holes are required for the function and the weight reduction of structure and machinery. However, the serious stress concentration occurs because of the geometric discontinuity caused by the holes and cutting section. In this study, it is attempted to obtain the stress concentration coefficients of the inner surface of the hole boundary by changing the position and the shape of holes on the homogeneous isotropic plate. And the effects on the plate are investigated. The results show that the stress level becomes low and the distribution area widens the position of stress concentration changes as the ratio a/b increases and change to a circle. And as the ratio a/l decreases, the stress concentration reduces. As the plate with three holes. the stress $\sigma$$\_$x/ and $\tau$$\_$xy/ of hole 1,3 becomes high, especially $\sigma$$\_$x/ dominant and high.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.5
• /
• pp.198-204
• /
• 2004

Dynamic fracture is investigated in plate applied by impacting bar. Numerical simulations of the experiments are made by using a finite element method(FEM) code, LS-DYNA. The eroding surface-to-surface contact allows between impacting bar and impacted plate. The occurrence of hourglass deformations in an analysis can invalidate results and hourglass energy is minimized to obtain the good accuracy of result. Total, internal and kinetic energies, von Mises plastic stress and X,Y,Z velocities of impacting bar are analyzed in this study.

• The Journal of Korean Orthopaedic Ultrasound Society
• /
• v.7 no.1
• /
• pp.67-75
• /
• 2014

There are several kinds of regional nerve blockades, such as interscalene brachial plexus block, C5 root block, suprascapular nerve block, and axillary nerve block, which can be applied for anesthesia and postoperative pain control after shoulder surgeries. These regional nerve blockades have shown good results, but high failure rate and serious complications, such as phrenic nerve palsy, pneumothorax, and nerve injury, still remain. Ultrasound-guided intervention can increase the success rate of nerve blockades and reduce complications. We described the method of ultrasound-guided intervention for the regional nerve blockades around shoulder.