• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.10
• /
• pp.823-832
• /
• 2018

In general, the fidelity of the aircraft dynamic model is verified by comparison with the flight test results of the target aircraft. Therefore, the reference flight data for performance comparisons must be extracted. This process requires a lot of time and manpower to extract useful data from the vast quantity of flight test data containing various noise for comparing fidelity. In particular, processing of flight data is complex because rotorcraft have high non-linearity characteristics such as coupling and wake interference effect and perform various maneuvers such as hover and backward flight. This study defines flight data processing criteria for rotorcraft and provides procedures and methods for automated processing of static and dynamic flight data using data mining techniques. Finally, the methods presented are validated using flight data.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.1
• /
• pp.66-72
• /
• 2007

an approach to air-vehicle design, an application of the radio-controlled model flight test techniques has been presented. The approach presented in this study is to validate the air-vehicle design configuration by analyzing the flight test results of scale model with dynamic similarities, and then to apply the analyzed results to the aerodynamic design process in early stage of the air-vehicle development. To develop practically applicable similarity laws for the subscale flying model design, the air-vehicle motions are decoupled into rotational motions for stability & control similarities and translational motions for flight performance similarities. Also, detail techniques for radio-controlled model flight test have been developed. Based on the results obtained from the radio-controlled flight test, the present approach for air-vehicle design has shown to be useful to validate the air-vehicle design configuration.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.1
• /
• pp.73-78
• /
• 2007

The process and results of Captive Flight Test(CFT), conducted by Agency for Defense Development(ADD) using the Korean KTX-1 trainer and external fuel tank, are presented. Through over 150 sorties of CFT, the guided weapon system's critical subsystems like Seeker, Navigation Device and Technology, Inertial Sensor, and Radio Altimeter are tested and evaluated. Using the CFT, time and cost are saved in weapon system research and development procedure.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.8
• /
• pp.813-822
• /
• 2010

Integrated data processing for display of flight critical data and mission critical data was conducted without additional display instruments using glass cockpit design. Based on a pre-designed flight critical system and a mission critical system, this paper shows an optimal design of subsystem integration. The design satisfies safety requirements of flight control systems(FCS) and requires minimized modification of pre-designed systems. By conducting integration test using System Integration laboratory(SIL), it is confirmed that the introduced design approach meets the safety requirements of the MEP system.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2010.11a
• /
• pp.921-924
• /
• 2010

정지궤도 위성을 제외한 대부분의 저궤도 위성 및 심우주 관측용 위성은 임무를 수행하면서 하루동안에도 제한된 시간동안만 지상국과의 통신이 가능하다. 따라서 위성 운영에 고수준의 자율적 제어기능이 요구된다. OBCP(On-Board Control Procedures)는 별도로 개발된 언어로 작성한 작은 용량의 스크립트 프로그램을 통해 위성을 제어하는 기능을 제공한다. 이러한 방법을 통해 지상관제 시에 위성의 임무수행동안 수행되어야 하는 다양하고 복잡한 운영 시퀀스를 용이하게 준비하고 업로드할 수 있다. OBCP는 위성비행소프트웨어와는 분리된 별도의 서브시스템으로 수행되기 때문에 새로운 위성운영 프로시져의 생성을 위해 위성비행소프트웨어의 수정, 재검증, 코드업로드 등의 절차가 요구되지 않으며 지상에서 개발 및 검증시험을 완벽하게 수행할 수 있다. 본 논문에서는 기존의 저궤도 관측위성에서 사용되었던 위성의 자율적 제어 시퀀스 기능과 OBCP의 기능을 비교하여 설명하고, 실제 Herschel and Plank 위성에 활용된 예를 통해 OBCP의 개념 및 설계 방안에 대하여 소개한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.5
• /
• pp.127-133
• /
• 2002

The general requirements to achieve the structural integrity of the airframe are described in the military specification, MIL-STD-1530A. One of these requirements is the durability and damage tolerance of the airframe, which should be shown through the analysis and test based on the related specifications. This paper introduces the full scale durability test to evaluate the structural safety and durability of the basic trainer, KT-1. The test was performed according to the procedure in the military specification. The flight by flight load spectrum was developed by KT-1 fatigue load criteria and used for the durability test. The durability test had been performed for 4 service lives and was completed successfully. Therefore, it was shown that KT-1 airframe satisfied the durability requirements.

• Journal of Advanced Navigation Technology
• /
• v.25 no.1
• /
• pp.52-59
• /
• 2021

According to the International Air Transport Association (IATA), 61% of the accidents occurred during the approach and landing phase of the flight, with 16% of the accidents caused by unstable access of the commercial aircraft. It was identified that the pilot's unstable approach and poor manipulation of correction led to accidents by continuing the excessive approach without go-around manuever. The causes of unstable access may vary, including airport approach procedures, pilot error, misplanning, workload, ATC (Air Traffic Contol) congestion, etc. In this study, we use the flight data analysis system to select domestic case airports and aircraft type where unstable approach events occur repeatedly. Through flight data analysis, including main events, airport approach procedures, pilot operations, as well as various environmental factors such as weather and geographical conditions at the airport. It aims to identify and eliminate the tendency of unstable approach events and the causes and risks of them to derive implications for mitigating unstable approach events and for developing navigation safety measures.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.12
• /
• pp.994-1001
• /
• 2013

Process of helicopter development is divided in design, manufacture and test & evaluation phase. Test & evaluation is performed step by step in order of component test, rig test, system ground test and flight test. After completing ground test and before first flight, US military specification requires 50hrs-PFAT in order to assure flight safety. PFAT is the test which requires tie-down and severe load imposition and it needs special ground test vehicle which is similar to helicopter prototype as well as much cost and period. In case of KUH, we have performed tailored PFAT considering KUH development environment. In this paper, we propose a proper way to perform the PFAT in accordance with development environment by giving KHU PFAT procedure and result.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.10
• /
• pp.51-59
• /
• 2005

In this paper, results of a multiple spacecraft formation-keeping control using the orbital relative motion and optimization technique are presented. To analyze and predict the relative motion between the formation-flying satellites, a closed-form orbit propagator obtained using the method of ephemeris compression is used. This closed-form orbit propagator is combined with optimization technique to plan a series of impulsive maneuvers, which maintain the formation configuration within the specified limit. As an example, this method is applied to the problem of maintaining the projected circular formation geometry and results from nonlinear simulation are presented.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.7
• /
• pp.569-576
• /
• 2013

The Airworthiness Certification from the government has an increasingly important role due to the dramatic growth of military aircraft development industry. It is a mandatory process of qualifying the flight safety within the aircraft's operational boundaries throughout its life cycle. The introduction of airworthiness certification has resulted in development paradigm shift from one requirement for one consumer need to the common requirement for many needs. This research paper provide the refinement of airworthiness certification criteria related to the flight control law and the verification methods which comply with its criteria.