• Journal of the Korean Geotechnical Society
• /
• v.33 no.4
• /
• pp.5-15
• /
• 2017

Three-hinge failure occurs in a jointed rock slope with a joint set parallel with slope and a conjugate joint set. Limit Equilibrium Method (LEM) and Finite Element Method (FEM) which are commonly used for slope design, are not suitable for evaluating stability against three-hinge failure, and this study performed parametric study to analyze the failure mechanism and to find influence factors causing three-hinge failure using UDEC which is a commercial two-dimensional DEM based numerical program. Numerical analyses were performed for various joint structural conditions and joint properties as well as ground water conditions. It was found that pore water pressure is the main factor triggering the three-hinge failure and the mode of failure depends on friction angle of basal joint and bedding joint set. The results obtained from this study can be used for adequate and economic footwall slope reinforcement design and construction.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.1
• /
• pp.109-115
• /
• 2008

Malfunction of gutter systems in the slope area accelerate to percolate surface flow into underground and to cause the decrease of soil strength, Overflowing from gutter causes soil erosion from slope surface, secondary it is one of the main reasons to cause disaster in the hillside area. Much researches were reported and are undergoing about flood disaster in the down stream area, but rare in the upper reach(hillside). It is considered that improving function of gutter in the hillside is very important to prevent the disaster caused by rainfall. In this paper, After analyzing relationship between rainfall and disaster on the hillside in Busan, researches about having surface flow run into gutter effectively and preventing from overflowing outside of gutter on the hillside in Busan were carried out. Improved design methods of gutter are suggested to mitigate disaster in the sloping area by analysis of collected data and hydraulic model test.

• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.515-523
• /
• 2020

If the safety factor does not secure the safety factor suggested in the design standard at the slope design stage, the safety factor is secured by installing an anchor. Stability analysis is used to verify the effect of reinforcing the slope of the anchor, but in this process, most of the anchor construction intervals are assumed to be equal and analyzed. For economical and effective slope reinforcement, stability analysis is required by adjusting the anchor construction interval. In this study, the effect of the anchor construction interval on the change of the safety factor of the slope was identified. Stability analysis was performed by setting a virtual slope with two berms and different anchor construction intervals. As a result of the analysis, the stability of the slope is secured when the anchor spacing of the lower surface is narrowed and the anchor gaps of the upper and middle surfaces are wider than when anchors are installed at the same intervals on the upper, middle, and lower surfaces of the slope. The result was a 15% reduction in the amount of anchors. This means that, rather than reinforcing anchors at the same intervals, it is economical and effective to have an economical and effective reinforcement effect to vary the anchor construction intervals according to the slope characteristics.

• The Journal of Engineering Geology
• /
• v.22 no.1
• /
• pp.1-13
• /
• 2012

The purpose of this work is to gain a better understanding of the interrelationships between geological structures and slope failure in sedimentary rocks. In the studied slopes, construction-related slope failure could only be observed on the south-dipping slopes. This indicates that slope stability may be dependent on the angular relationships between the dip direction of bedding and the orientation of the slope. Slope failure continued, post-construction, around large fault zones in the studied outcrop; these fault damage zones are, however, not easily recognized in the field. Here we suggest a new method that uses accumulated fracture density to precisely identify fault damage zones. Multiple-faced slopes are now increasingly being exposed during large-scale construction projects in South Korea. This multiple-faced slope analysis indicates that the stability of a slope should be evaluated by identifying domains, through the analysis of possible slopes and their angular relationships with bedding and other discontinuities, prior to construction. Therefore, careful consideration of geological structures such as bedding and other discontinuities, and their angular relationships during the design of cuttings through sedimentary rocks, will increase the efficiency of construction and enable the safe construction of more stable slopes that will retain their stability after construction.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.3
• /
• pp.13-19
• /
• 2012

Due to recent climate change, big typhoon and heavy rainfall happen frequently not only in Korea but also all over the world. It leads to collapse of levee by extraordinary flood. It lead to collapse of levees by extraordinary flood. These natural disasters give the life and property damages in near region. In this study, it was performed that a stability in levee using seepage analysis. It has been evaluated hydraulic gradient of exit zone according to variations in levee crest width, gradient. As a result, it showed that hydraulic gradient of exit zone was decreased due to increase of levee crest width and gradient, and it was evaluated that vertical hydraulic gradient was decreased than that of the horizontal hydraulic gradient.

• Geotechnical Engineering
• /
• v.27 no.6
• /
• pp.11-16
• /
• 2011

• 기술발표회
• /
• s.2006
• /
• pp.172-181
• /
• 2006

• 지반과기술
• /
• v.9 no.2
• /
• pp.40-43
• /
• 2012

• 지반과기술
• /
• v.8 no.1
• /
• pp.54-57
• /
• 2011

• 지반과기술
• /
• v.8 no.2
• /
• pp.13-22
• /
• 2011