• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.446-447
• /
• 2010

본 논문에서는 전동기의 고정자 권선 절연파괴 고장을 분석하고 자기 인덕턴스 변화의 비선형성을 고려하기 위해 FEM 시뮬레이션을 이용하여 고장 현상을 해석하고, 실험을 통해 검증하였다. 제안한 고장의 모델링을 통하여 고정자 권선에서 단락이 발생하면 단락된 권선의 순환전류에 의해 고정자에 자기 포화현상이 발생하고, 입력전류의 불평형에 의하여 평균토크가 감소하고, 토크리플이 증가함을 확인 하였다.

• Proceedings of the KIPE Conference
• /
• 2017.11a
• /
• pp.71-72
• /
• 2017

본 논문에서는 비선형 최적화 기법을 이용하여 자기 포화(magnetic saturation) 및 교차 결합 현상(cross-coupling effect)을 고려한 매입형 영구자석 전동기(IPMSM)의 실시간 MTPA 제어 방법을 제안한다. 이는 토크 지령 추종과 최소 동손 운전을 만족하는 제한 최적화(constraint optimization) 문제로 접근할 수 있다. 이를 통해 유도한 연립 비선형 방정식의 경우, Levenberg-Marquardt 수치 해석법을 적용하여 안정적이면서 빠르게 해를 구할 수 있다. 이러한 방법을 이용하면 참조표(look-up table) 없이 운전 환경의 실시간 변동을 고려한 효율적인 MTPA 운전이 가능하다. 시뮬레이션을 통해 제안된 알고리즘의 전류 해가 최적 운전점과 일치함을 확인하였다.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.143-150
• /
• 2000

Depending upon the combination of tolerances specified in the standards on bolt, nut and washer for high tension bolt sets, there arises center-to-center deviation between bolt and washer. This deviation nay cause loss of effective contact area between nut- and washer-faces, which leads to some dispersion of the torque coefficient K. By adapting circular arc surface instead of flat surface for the nut, it is shown through numerical analyses that the dispersion of the torque coefficient can be minimized. In this way, optimum radius of curvature of the nut bearing surface is proposed.

• Proceedings of the KIEE Conference
• /
• 2005.10c
• /
• pp.186-188
• /
• 2005

BLDC 전동기는 선형적인 토크 대 전류, 속도 대 전압 특성을 갖고 있으며 기계적, 전기적인 잡음이 없고, 가감속 제어가 용이하며, 토크 대 관성의 비가 매우 높아 소형으로 높은 출력을 낼 수 있다는 장점을 가지고 있다. 그러나 전기자 전류의 전환(Commutation)시 고정자 권선의 인덕턴스 성분과 역기전력으로 인해 발생되는 전류 리플은 BLDC 전동기 토크리플의 중요한 원인이 된다. 이에 본 논문에서는 고속 연산이 가능하고 별도의 외부 메모리 없이 칩 하나로 모든 동작을 할 수 있는 TMS320LF2407 DSP칩을 사용, Hard-chopping PWM 방식을 이용하여 전류 리플을 감소시켰으며, 이를 시뮬레이션 및 실험을 통해 증명하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.7
• /
• pp.677-684
• /
• 2010

Backlashes of gears provide gears for good lubrication and for removal of the interference between teeth by the wear and manufacturing errors. The backlash is the strong nonlinear factor to gears. This study deals with nonlinear modeling of helical gears with backlash. Excitation of helical gears comes from torque variation, the tooth surface error, and the periodical change of mesh stiffness. To study the effect of torque fluctuation, equation of motion for the single degree of freedom torsional model of helical gears with the periodical change of mesh stiffness and the backlash was derived. The Newmark beta method and the Newton-Raphson method were used to obtain the nonlinear behaviors of mesh forces of helical gears. All excitation frequencies initially caused the tooth separation and single-sided impacts of the gear pair and eventually led to the normal tooth contact. However, some special excitation frequencies caused the single-sided impacts in the entire time as well as the initial time. Damping increase reduced the duration of single-sided impacts, and the backlash increase caused those in the entire time domain.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.12
• /
• pp.2618-2624
• /
• 2009

Harmonics (or distortion in wave form) has always existed in electrical power systems. It is harmless as long as its level is not substantial. However, with the recent rapid advancement of power electronics technology, so-called nonlinear loads, such as variable frequency drives for motor power/speed control, are increasingly finding their way to shipboard or offshore applications. In this paper a new approach to direct torque control (DTC) of induction motor drive is presented. In comparison with the conventional DTC methods the inverter switching frequency is constant and is dramatically increased, requiring neither any increase of the sampling frequency, nor any high frequency dither signal. The well-developed space vector modulation technique is applied to inverter control in the proposed DTC-based induction motor drive system, thereby dramatically reducing the current harmonics. As compared to the existing DTC approach with constant inverter switching frequency, the presented new approach does not invoke any concept of deadbeat control, thereby dramatically reducing the computations.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.4
• /
• pp.309-317
• /
• 2000

This paper presents the switching angle and voltage to maximize torque/efficiency and minimize torque ripple in the 4-phase 6-poles Switched Reluctance Motor(SRM). SRM drive has high saturation and nonlinear characteristics of inductance. So we cannot hard to find optimal condition by using analytic method. Therefore it is hard to find the operating the switching angle and voltage through the approximated analysis and computer simulation by using SIMULINK according to the speed and torque required by load. From the results, we can say that the optimum average voltage is determined by the load only and the speed is determined by the optimum turn-on/off angle only. And the maximum efficiency and minimum torque ripple depend on switching angle, not on voltage. And then one-chip microcontroller controls the switching angle and voltage of an asymmetrical inverter in the SRM driver. This drive method, which is expect that the driving methods, which are maximizing torque/efficiency and minimizing torque ripple, will be suitable for the electric vehicle, the industrial application and household appliances.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.2
• /
• pp.123-128
• /
• 2022

The torque of the SRM((Switched Reluctance Motor)) is proportional to the inductance slope, so it has a non-linear torque characteristic, and has a disadvantage in that the torque pulsation is large and noise is severe. In particular, the biggest obstacle to the commercialization of SRM is the pulsating torque generated from the rotating shaft, which has various adverse effects not only on the device itself but also on the peripheral devices. Therefore, various methods for reducing the pulsating torque have been published by domestic and foreign researchers, and there is a study result that the hysteresis controller has an advantage in that it can flow a smooth current compared to the chopping control. However, in determining the hysteresis band, if the band is too small, it has a disadvantage in that it may cause a switching loss due to many switching and an unstable initial start when the encoder is used. Therefore, in this paper, a variable hysteresis controller that can reduce torque ripple in a steady state while having a more stable and fast speed response through the change of the hysteresis band according to the speed error.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.4
• /
• pp.78-89
• /
• 2012

The generated torque of a switched reluctance(SR) motor is highly nonlinear, which makes it difficult to determine the reference current commands for minimum torque ripples. In this paper, we present a computationally simple and efficient method to minimize torque ripples of SR motors based on iterative learning control. The reference current command of each phase minimizing torque ripples is identified in 2-dimensional look-up table form. Our learning control algorithm does not require the torque model, so our method is not affected by model errors and hence is very accurate. In order to justify our work, we present some computer simulation results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.1
• /
• pp.10-18
• /
• 1998

불확실한 변수와 비선형성을 가지는 유연조인트 로봇의 견실제어 방안을 제시한다. 그리고 본 시스템에서 불확실구조는 일치성을 유지하지 않는 불일치성 불확실 시스템이다. 제어기는 리아노프의 방안에 근거를 두고있다. 견실제어는 연산토크법을 사용하고 삽입제어기법을 통하여 좌표변환을 통해 구성된다. 제어기 설계과정은 우선 연산토크방법에 의해 시스템 동역학에서 정격부분을 선형으로 2개의 부분시스템으로 구성한다. 이후 좌표변환을 이용하여 각 부분시스템에 제어기를 구축한다. 이 방안을 통하여 관성 행렬이 알려진 값인 경우 이 행렬의 상위한계 조건없이 제어기를 설계할 수 있다. 따라서 임의의 형태의 로봇에도 적용 가능한 제어알고리즘이 된다. 설계된 견실제어는 변환된 시스템이나 원시스템 모두 실용적 안정성을 보장한다. 이 변환은 단지 불확실변수의 최대 한계값의 정보만을 요구한다.