• Polymer(Korea)
• /
• v.25 no.1
• /
• pp.133-141
• /
• 2001

The friction and wear properties of carbon-carbon composites made with different weight percent of $MoSi_2$ as an oxidation inhibitor were investigated using a constant speed wear test apparatus in an oxidation environment. The results indicated the carbon-carbon composites undergoing an abrupt transition of friction coefficient, from low-friction behavior(${\mu}$=0.15~0.2) during normal wear regime to the high-friction behavior(${\mu}$=0.5~0.6) during dusting wear regime at the frictional temperature range of 150~180${\circ}C$. The existence of temperature-dependent friction and wear regimes implied that the performance of specimen made with carbon-carbon composites was markedly affected by the thermal properties of the composites. The carbon-carbon composites filled with MoSi2 exhibited two times lower coefficient of friction and wear rate in comparison with the composites without $MoSi_2$. Especially, the composites containing 4wt% $MoSi_2$ filler showed a significantly improved activation energy for wear due to the reduction of both the porosity and powdery debris film formation on sliding surface when compared to those without $MoSi_2$.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.1
• /
• pp.57-78
• /
• 2022

The disc cutter and cutterbit, which are the most important factors to increase the excavation efficiency of TBM, are key factors in the design and construction of the cutter head. The arrangement, spacing, number, size, and material of disc cutters suitable for the ground conditions determine the success or failure of TBM construction. The disc cutter, which is a representative consumable part in TBM construction, can cause enormous disruption to the construction cost as well as the construction cost unless accurate prediction of wear and replacement cycle is accompanied. Therefore, in this study, the method of calculating the replacement cycle of the disc cutter calculated at the time of design for the slurry shield TBM field, and the depth of wear and replacement location of the disc cutter that occurred during actual construction were compared by analyzing the field data. For a quantitative comparison, weathered soil/weathered rock, soft rock, and hard rock were classified according to the ground in the section showing constant excavation data, and the trajectory of circle was different depending on the location of the disc cutter, so it was compared and analyzed.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.4
• /
• pp.623-630
• /
• 2015

Prepared polyurethane resin for buffalo leather coating on surface was synthesized with addition reaction glycerol which had different mole ratio. Mechanical properties of the synthesized polyurethane resin were measured by the SEM, FT-IR, UTM. Growing concerns in the evnironment-friendly polymer resin, we have synthesized low late obtained solvent water dispersion resin to be coating on buffalo leather. The increase of aliphatic trihydric alcohol glycerol mole %, abrasion resistance and tensile strength had demonstrated reduce properties. On the contrary, elongation and flexibility properties had highly increased. In the result of toluene solvent resistance, there was no effect of increased or decreased by the ratio of glycerol mole %.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.1
• /
• pp.100-107
• /
• 2015

Prepared polyurethane resin for vegetable leather coating on surface was synthesized with glycerol which had different mole ratio. Mechanical properties of the synthesized polyurethane resin were measured by the SEM, FT-IR, UTM. Growing concerns in the evnironment-friendly polymer resin, we have synthesized low late obtained solvent water dispersion resin to be coating on vegetable leather. The increase of aliphatic trihydric alcohol glycerol mole %, abrasion resistance and tensile strength had highly stronger in intensity and longer durability. On the contrary, demonstrated reduce properties of elongation and flexibility. In the result of toluene solvent resistance, there was no effect of increased or decreased by the ratio of glycerol mole %.

• Resources Recycling
• /
• v.14 no.1
• /
• pp.39-46
• /
• 2005

A solid-state high power torch with inter-electrode insert (IEI) was developed to treat solid waste (for example, incinerated ash), and it's operation characteristics were obtained in the plasma facility test for waste treatment. According to torch test from this study, at the non-transferred mode voltage is increased by gas volume proportionally, and at the transferred mode it is not affected to voltage change. Especially arc voltage is sustained stable at the range of 10% of total Fe in slag. In addition, Electrical conductivity is 0.05~0.25${\Omega}^{-1}cm^{-1}$, torch efficiency is 75~85% and Erosion rate is 2${\times}10^{-6}~6{\times}10^{-6}$ kg/s.

• Journal of Korean Ophthalmic Optics Society
• /
• v.9 no.1
• /
• pp.125-134
• /
• 2004

By applying the test methods of "Protection Eyewear Standard (KS P 8147)", "Glasses Frame Standard (KS G 3306)" and "Lens Standard for Sunglasses (KS P 4404)", this study analyzed optical functions of sunglasses now being sold in a road shop (A shop), a fashion goods store (B shop), a shop of highway rest area (C shop) and an optical shop (D shop). When compared with sunglasses (UV transmittance rate 8.8%) of a road shop, UV Block effects of sunglasses (UV transmittance rate 0.7%) of an optical shop showed good results. In addition, the average surface resistance against abrasion for sunglasses which was sold at an optical shop was 1.4% that was much higher than that of sunglasses of a road shop(2.2%).

• International Journal of Highway Engineering
• /
• v.7 no.3 s.25
• /
• pp.93-100
• /
• 2005

Rock produced in situ has been used as the road construction materials in consideration of economies. However, because sedimentary rock is rapidly weathered, it is hard to decide appropriateness of quality specifications. This study aims at evaluation of usability for sub-base of muddy stone produced in situ. Test results show that the abrasion ratio is fitted for specifications, but weight loss in 37.5$\sim$16mm after Los Angeles abrasion test shows 47% in muddy stone in comparison with 20$\sim$30% in gneiss and sandstone. The soundness of aggregate shows higher value in muddy stone than in gneiss and sandstone. The weight loss from accelerated weathering test due to freezing and drying show 58% in muddy stone in comparison with 308$\sim$21% gneiss and sandstone.

• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.89-96
• /
• 1999

Manufacturing conditions of the porous alumina mold were established to overcome various limits of the gypsum mold. For the preparations of the porous alumina mold, an activated charcoal was added to the Al2O3 with the wt% variation and then mixed. The binary slurry was study dispersed based on the examination of the ESA and rheological behaviro. The cylinder type alumina mold was cast in the gyspum mold and characterized by the shrinkage rate at the variable sintering temperature and the resistance against wear. It was proper to make a sintering of the Al2O3 by the surface diffusion which was non-shrinkage sintering mechansim, and intergranular neck growed stronger while sintering was being made. We studied a sintering by three categories; 1) thermodynamic method below 1,000$^{\circ}C$, 2) kinetic method above 1,000$^{\circ}C$ and 3) combined method. In the results of the respective works, combined method was superiro to the others. The prepared Al2O3 mold had relatively high strength, low drying rate, the resistance against the acid or base and good casting behavior.

• Journal of Conservation Science
• /
• v.32 no.4
• /
• pp.459-469
• /
• 2016

The goal of this study was to examine property changes induced by the choice of filler used with an epoxy resin that was developed in 2014 to restore cultural assets and consider the applicability of the resin as a restorative agent. The properties of putty mixed with 9 types of fillers and as-developed resins were compared with those of existing materials with regard to stability, superiority and applicability. The potential of the putty as an alternative material was also examined. The materials produced the best adhesiveness, color change and hardness results when mixed with lime. Micro balloon produced the best wear rates and hardening times, while diatomite produced the best tensile and compressive strengths. A plaster and white mineral pigment mixture produced the best specific gravity. Every material except for lime exhibited about 2.5-20 times higher wear rates than the existing material, which is thought to exhibit an excellent cutting force. The hardening time was enhanced by about 0.5-9 times to improve convenience. The stability of the relic was also ensured by improving hand staining without any shrinkage or deformation. The material exhibited about 0.5-27 times less yellowing. Thus, it is thought to be a material that can reduce property changes and reduce the degree of relic fatigue which occurs during reprocessing and sense of difference from relic.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.249-250
• /
• 2010

This study analyzes the basic characteristics of the concrete using recycled coarse aggregates produced by using a rotary crusher and compares it to that of using a cone crusher. As a result, the recycled aggregate produced by using the rotary crusher represents more excellent results in fluidity and compressive strength according to the increase in the replacement rate of recycled aggregates than that of using the cone crusher. It can be analyzed that it was due to the fact that the particle shape of the recycled aggregate produced by using the rotary crusher showed round figures relatively and that leaded to reduce friction force and remove lots of grouted mortar caused by its wearing.