• Journal of the Korean Society for Railway
• /
• v.12 no.1
• /
• pp.55-64
• /
• 2009

Recently, concrete track is replacing ballast track for efficient and economic maintenance of track. It considerably offer less maintenance, a longer service life and reduced life-cycle costs. With the aim of achieving high-quality track construction work, of developing tools for quality assurance in new construction and for later technical inspection of material condition, a quality strategy has to be developed. For these purpose, NDT which is using the seismic wave has carried out in situ studies in the test construction section. The used NDT are SASW test, impact echo test and continuous impact echo test. The test is performed 5,353 times on 49 pre-cast concrete track panels to verify the stiffness structure and grouting efficiency of the track structure. To conclude, because of the non-homogeneous characteristic of concrete material. it is restricted to apply the elastic wave test at some aspect. However it is possible to acquisite a sufficient reliability about structural stiffness and grouting efficiency of concrete track.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.6
• /
• pp.289-294
• /
• 2010

Ni-YSZ (Yttria Stabilized Zirconia) composite powders for SOFC were fabricated by glycine nitrate process. $ZrO(NO_3)_2{\cdot}2H_2O$, $Y(NO_3)_3{\cdot}6H_2O$, $Ni(NO_3)_2{\cdot}6H_2O$ and glycine were chosen as the starting materials. The structural properties of the sintered Ni-YSZ cermets have been investigated with respect to the volume contents of Ni. A porous microstructure consisting of homogeneously distributed Ni and YSZ phases together with well-connected grains was observed. The sintered Ni-YSZ cermets showed a porous microstructure consists of homogeneously distributed Ni and YSZ phases and the grains were well-connected. It was found that the open porosity is sensitive to the volume content of Ni. The Ni-YSZ cermet containing 35 vol% Ni seems to be suitable for the electrode material of SOFC since it provides sufficient open porosity higher than 30%.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.1
• /
• pp.101-108
• /
• 2004

For the last 30 years, the use of EPS as a lightweight filling material has grown significantly throughout the world. The fields of applying EPS block have also increased. The most representative example in geotechnical applications is using EPS block as a compressible inclusion that causes the reduction of static earth pressure on earth-retaining wall, bridge abutment and pipes. EPS blocks have a good workability by its lightweight characteristic and a uniform engineering property with the change of its density. Also EPS blocks have best material property as a compressible inclusion. This paper analyzes that the compressible inclusion function of EPS causes the reduction of static earth pressure on retaining wall and concrete box culvert. A series of in-situ tests were conducted to evaluate the reduction of static earth pressure using EPS inclusion. Based on in-situ test, it is found that the magnitude of static earth pressure was reduced to about 20% for the retaining wall and about 45∼53% for the box culvert compared with theoretical active earth pressure.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.25-37
• /
• 1993

This paper describes the use of the J-integral, a one parameter of the non-linear fracture mechanics(NLFM), as a means to measure toughness of steel fiber reinforced concrete. This parameter can be conveniently evaluated from experimentally determined load-deflection curves from flexural tests when a maximum-load failure criterion is employed. And, for high strength concrete which was reinforced steel fiber, with two different fiber length in the form of notched beams, were tested under 3-point bending, and $J_{IC}$, as well as the linear elastic fracture mechanics(LEFM) parameters $K_{IC}$ and $G_{IC}$ were evaluated. The results suggest that $J_{IC}$ is a promising fracture criterion for all of these. while $K_{IC}$(or $G_{IC}$) almost certainly are not. Also it was found that a fiber addition of less than 0.5% did not improve the fracture toughness of the high strength concrete. However, at more than 1.0% in fiber contents, $J_{IC}$ showed significant increases. reflecting the changed character of the concrete; $K_{IC}$ and $G_{IC}$ did not.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.25-25
• /
• 2021

점착성 유사는 비점착성 유사에 비해 1차입자의 크기가 작아 1차입자간의 점착력이 중요한 역할을 하는 유사를 말한다. 점착성 유사는 비점착성 유사에 비해 크기가 작아 입자의 전자기적 점착력의 영향을 무시할 수 없으므로 점착력으로 인해 입자들은 서로 응집하는 동시에 입자들 간의 충돌에 의하여 파괴되는 과정을 거친다. 이러한 응집과 파괴가 지속되는 일련의 과정을 응집현상이라 한다. 점착성 유사는 응집과정을 통해 일차입자보다 크기가 크며 수십 개에서 수천 개의 일차입자와 물의 덩어리인 플럭을 형성하게 된다. 흐름 내 존재하는 플럭의 응집현상에 가장 지배적인 영향을 미치는 인자로 난류 거동이 알려진 바 있다. 본 연구에서는 난류 거동에 따른 점착성 플럭의 입도분포 변화를 살펴보고자 하였으며, 점착성 유사 입도분포 모형을 개발하였다. 수치모형의 개발은 확률과정(또는 추계과정)의 개념을 바탕으로 한다. 점착성 유사의 응집현상을 구성하는 응집과정은 다양한 연구를 통해 메커니즘들이 규명된 것과 달리 파괴과정은 난류로 인해 발생하며 무작위한 것으로 여겨진다. 무작위한 플럭의 파괴과정을 확률과정으로 가정하고 매개변수 중 하나를 대수정규분포를 따르는 난수로 고려하였다. 개발된 모형의 검증은 연안지역에서 점착성 플럭의 거동을 측정한 연구결과와의 비교를 통해 수행하였으며, 흐름 유속의 연직분포와 유사 농도의 연직분포, 응집현상 이후 플럭의 평형크기와 입도분포가 모두 합리적으로 계산되는 것이 확인되었다. 더불어 모의 결과에서는 대수정규분포를 따르는 동일한 난수를 적용하였음에도 불구하고 하상으로부터 거리가 가까워짐에 따라 플럭입도분포가 단봉분포(Unimodal Distribution)와 이봉분포(Bimodal Distribution)가 모두 계산되는 것으로 나타났다. 이는 모형의 개발과정에서 플럭의 가능 최대 크기를 콜모고로브 길이규모로 제한한 것과 관련이 있다. 난류 흐름 내 존재하는 플럭의 크기가 응집현상을 통해 난류의 콜모고로브 길이규모까지 성장하는 경우, 난류의 전단응력이 급격하게 증가하여 파괴과정이 활발해지고 응집과정이 저하된다는 것은 널리 알려진 사실이다. 이러한 사실을 바탕으로 플럭의 가능최대 크기를 콜모고로브 길이규모로 제한하였으며, 하상으로부터의 거리에 따라 콜모고로브 길이규모의 변화로 인해 콜모고로브 길이규모 부근에서 하나의 최빈값이 추가로 나타나는 것으로 이해된다. 수치모의 결과로부터 얻어진 콜모고로브 길이규모와 입도분포 형태의 상관관계를 보다 정확하게 이해하기 위해 실측 자료들을 검토해 본 결과, 균질한 재료를 이용한 실험실 실험결과에서 플럭 이봉분포의 최빈값이 콜모고로브 길이규모와 일치하는 것이 확인되었다. 연안지역에서 측정을 수행한 자료들에서도 이봉분포 또는 다봉분포와 콜모고로브 길이 규모와의 상관성을 찾아볼 수 있었다.

• Korean Journal of Materials Research
• /
• v.4 no.8
• /
• pp.906-914
• /
• 1994

Plastic behavior of two-phase intermetallic compounds based on $LI_{2}$-type $(Al, Cr)_3$ Ti was investigated using compression test at R.T. and 77K. $LI_{2}$ single phase alloys and two-phase alloys consisting of mainly $LI_{2}$ phase and a few or 20% second phases were selected from AI-Ti-Cr phase diagram. In general, compared with Llz single phase, two-phase alloys consisting of 20% second phase showed relatively high yield strength and poor ductility. Among the alloys, however, AI-21Ti-23Cr alloy consisting of 20% $Cr_{2}Al$ phase showed available ductility as well as high yield strength. Plastic behavior of $LI_{2}$ single phase alloys and two-phase alloys consisting of a few% $Cr_{2}Al$ was also investigated. Homogenization of arc melted ingots substantially reduced the amount of second phases but introduced extensive pore. When Cr content increased in $Ll_{2}$ single phase alloys after the homogenization, the volume fraction of pore in the alloys decreased, and no residual pore was observed in two-phase alloys consisting of a few% $Cr_{2}Al$ phase. Environmental effect on the ductility of the alloys was investigated using compression test at different strain rates($1.2 \times 10^{-4}/s$ and $1.2 \times 10^{-2}/s$). Environmental embrittlement was least significant in A1-25Ti-10Cr alloy consisting of LIZ single phase among the alloys tested in this study. However, based on the combined estimation of the pore formation, environmental embrittlement and ingot cast structure, AI-21Ti-23Cr alloy consisting of 20% $Cr_{2}Al$ as the second phase is expected to show the best tensile elongation behavior.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.12
• /
• pp.19-30
• /
• 2010

Bentonite-based grout has been widely used to seal a borehole constructed for a closed-loop vertical ground heat exchanger in a geothermal heat pump system (GHP) because of its high swelling potential and low hydraulic conductivity. Three types of bentonites were compared one another in terms of viscosity and thermal conductivity in this paper. The viscosity and thermal conductivity of the grouts with bentonite contents of 5%, 10%, 15%, 20% and 25% by weight were examined to take into account a variable water content of bentonite grout depending on field conditions. To evaluate the effect of salinity (i.e., concentration of NaCl : 0.1M, 0.25M, and 0.5M) on swelling potential of the bentonite-based grouts, a series of volume reduction tests were performed. In addition, if the viscosity of bentonite-water mixture is relatively low, particle segregation can occur. To examine the segregation phenomenon, the degree of segregation has been evaluated for the bentonite grouts especially in case of relatively low viscosity. From the experimental results, it is found that (1) the viscosity of the bentonite mixture increased with time and/or with increasing the mixing ratio. However, the thermal conductivity of the bentonite mixture did not increase with time but increased with increasing the mixing ratio; (2) If bentonite grout has a relatively high swelling index, the volume reduction ratio in the saline condition will be low; (3) The additive, such as a silica sand, can settle down on the bottom of the borehole if the bentonite has a very low viscosity. Consequently, the thermal conductivity of the upper portion of the ground heat exchanger will be much smaller than that of the lower portion.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.1
• /
• pp.21-26
• /
• 2011

Ni-YSZ (Yttria Stabilized Zirconia) composite powders were fabricated by glycine nitrate process. The prepared powders were sintered at $1300{\sim}1400^{\circ}C$ for 4 h in air and reduced at $1000^{\circ}C$ for 2 h in a nitrogen and hydrogen atmosphere. The microstructure, electrical conductivity, thermal expansion and mechanical properties of the Ni-YSZ cermets have been investigated with respect to the volume contents of Ni. A porous microstructure consisting of homogeneously distributed Ni and YSZ phases together with well-connected grains was observed. It was found that the open porosity, electrical conductivity, thermal expansion and bending strength of the cermets are sensitive to the volume content of Ni. The Ni-YSZ cermet containing 40 vol% Ni was ascertained to be the optimum composition. This composition offers sufficient open porosity of more than 30 %, superior electrical conductivities of 917.4 S/cm at $1000^{\circ}C$ and a moderate average thermal expansion coefficient of $12.6{\times}10^{-6}^{\circ}C^{-1}$ between room temperature and $1000^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.4 no.5
• /
• pp.600-607
• /
• 1994

Optimum exper~mental conditions were established for the growth of heteroepitaxial GaAs layers on InP using liquid phase epitaxy (LPE) technique. Results showed that the optimum growth temperature was $720^{\circ}C$ at a cooling rate of $0.5^{\circ}C$/min. Surface morphology of the grown layers significantly improved by addition of about 0.005wt% Se to the Ga growth melt, which effectively suppressed melt-back of InP substrates into the melt during the initial stage of growth. It was observed that the quality of GaAs layers also improved substantially when the substrates patterned with grating structure were used, as determined by the (400) double crystal X-ray diffraction. The transmission electron microscopy observation indicated t.hat the misfit dislocations interact with each other at the grating region, resulting in a lower dislocation density in the upper GaAs layer.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.4
• /
• pp.100-117
• /
• 2020

National Treasure no. 101, the stupa of State Preceptor Jigwang from the Beopcheonsa Temple Site in Wonju has been transferred from place to place and reassembled several times since it was built. In particular, overall dismantling and repair was carried out in 1957 to restore parts damaged by bombing during the Korean War. Documented information on the repair process and materials used at that time does not exist. However, various types of metal materials used for this stupa have been identified during conservation work. Besides clamps anchor bolts, 9mm-thick circular rebars were mainly used for joining the parts of this stupa, while circular rebars and wires of various thicknesses were used for joining the parts with mortar restoration materials. Although deformed bars are typically used for stone pagodas classified as architectural structures, smooth circular rebars were used in this case. In terms of restoration using mortar, material shapes were transformed, bound alternately, and twisted irregularly to improve bonding strength and coherence in order to insert restoration materials and to bolster structural weaknesses. In addition, metallographic analysis showed the material to be hypo-eutectoid steel with low carbon content. Many non-metallic inclusions in the shape of drops of different sizes were included, which do not affect the whole elemental composition due to the very small quantities involved. Qualitative and EPMA analysis of Mn and S, which were not identified by SEM-EDS area analysis, established an even distribution of MnS in crystal grains of the microstructure, regardless of the shape of the samples. It is presumed that secondary homogenization and softening might have been conducted after manufacturing to facilitate the working process. Furthermore, in consideration of properties indicating that the thinner the steel is, the less carbon content contained and the greater the elasticity and elongation, it is judged that restoration work was ordered.