• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.39 no.2
• /
• pp.97-103
• /
• 2013

Recently, the importance of cleansing is emphasized according to increasing use of cosmetics. Even though many cleansing devices with a rotating brush are commercially available, there are no reports about cleansing devices with rotating brushes in Korean literature. In the present study, we evaluated the efficacy of cleansing device with a rotating brush which was named PBRCF1201 (Amorepacific Co., Korea). 20 volunteers were enrolled in this study. Before and after use of PBRCF1201, we measured the number of black head, skin brightness, desquamation index, sebum, and the number of pores on the face and forearm. Cleansing by cleansing device with a rotating brush was shown to cleanse better than manual cleansing. In addition, the number of black heads, skin brightness, desquamation index, sebum and the number of pore were also improved after cleansing. Therefore, the cleansing device with a rotating brush appears to be an effective cleansing method without causing injury or dryness.

• 베이커리
• /
• no.4 s.357
• /
• pp.110-111
• /
• 1998

• NEWSLETTER 전기공업
• /
• no.95-23 s.144
• /
• pp.22-43
• /
• 1995

• KIPE Magazine
• /
• v.3 no.4
• /
• pp.27-32
• /
• 1998

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.58-63
• /
• 2010

A new contact force estimation technique is proposed. Keeping the contact force at a certain level between finishing tool and the object is essential since the quality of the finished surface is very sensitive to the contact force during the finishing process. However, the contact force measurement cannot be obtained by simply installing load cells under machine table or in the middle of tool linkage. The reason is that the weight of the machine table and the tool linkage are much heavier than the force to be measured. To that end, a method for estimating disturbance is proposed for a system that is similar to the mechanism of the finishing machine, and the same method is applied to estimate the contact force of the brush-type finishing machine. To verify the effectiveness of the proposed method, a small scale test set-up has been built and the method has been tested.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.4
• /
• pp.98-107
• /
• 2005

Brushless DC motor(BLDCM) can be driven by 120[^{\circ}]$ square wave voltage and use PWM pulse patterns in two-phase feeding scheme to control the speed of the motor. This Paper introduces four PWM modes used BLDCM control system, and analyzes their different influences on the motor performances using a time-stepped voltage source finite element method. To verify the proposed computational method, we built the prototype motor for electrical power steering(EPS) and compared the predicted and the measured back EMF and phase current.

• Journal of computational fluids engineering
• /
• v.17 no.2
• /
• pp.58-64
• /
• 2012

Turbulent flows in a intake part of vacuum cleaner are studied by RANS simulations. The governing equations are solved by the SIMPLE algorithm based on the finite volume method of the unstructured grid system. The predicted results show that the suction performance is closely related to the variation of flow structure in the intake part. In order to investigate for the cleaning of bedclothes and carpet without sticking, several design changes are applied. The introduction of a solid cylinder in the intake part changes vortical structures significantly. Based on this result, a new design with spiral brushes is proposed. The design shows a good behavior for the suction performance and the flow control.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.1173-1176
• /
• 1995

We design and analyze two type stators for brushless DC linear motors by the experiment and the computational analysis. For a U-shape stator, the maximum manetic flux density by the finite element method(FEM) is large than that by the experiment by 1.0~2.2%. The result by the FEM is so accurate that it can be applied to the geometric design for the optimization. To increase the maximum magnetic flux density, we suggest an improved stator and analyze it by the 3-D and 2-D models. The maximum magnetic flux density of the improved stator is large than that of the U-Shape stator by 2.7%. Considering the size of the improved stator and maximum magnetic flux density, we determine that the optimized thickness is 5mm for a given specification.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.215-215
• /
• 2011

본 논문은 상용차용 전동 쿨링팬 모듈의 개발을 위한 5kW급 브러시리스 DC 전동기에 관하여 기술한다. 개발 대상전동기는 정격 3,000rpm의 회전속도를 목표로, 기존 팬 쉬라우드에 장착 가능한 박형으로 설계되며, 코깅토크 저감을 위한 회전자와 고정자 형상 최적화를 수행하여, 구동시 소음과 진동을 감소시키고자 하였다. 전동기를 제작하여 입출력 특성을 분석하고, 최종적으로 기 개발된 팬 블레이드와 결합하여, 쿨링팬 시스템의 유량 및 유압 특성시험을 진행하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.4
• /
• pp.582-588
• /
• 2002

This paper presents a efficient sensorless driving strategy for brushless dc motor(BLDCM). By varying PWM switching frequency(4KHz, 6KHz, 8KHz) properly according to the rotating speed, the improvement of the efficiency and the operating characteristics through the wide speed are obtained.. The experimental results show that the proposed method can efficiently improve the sensorless driving performance for BLDCM with trapezoidal back emf.