• Korean Chemical Engineering Research
• /
• v.40 no.6
• /
• pp.709-714
• /
• 2002

To investigate the decomposition kinetics of poly(ethylene terephthalate) the high pressure molten-polymer injector has been devised. Using the experimental apparatus equipped with batch reactor and high pressure molten-polymer injector the decomposition of PET has been performed at constant pressure of 250 bar and 300, 320, $340^{\circ}C$, respectively. At each temperature conditions the conversions after initial 1 minute have shown very high values such as 76-90%. As the temperature increases the conversion reaches more than 98% at 10 minutes. Based on the second order reaction model the reaction rate constants have been obtained. We can calculate the conversions within 2% errors utilizing optimized rate constants. The activation energy for the decomposition of PET at subcritical conditions has shown to be 54.4 kJ/mol.

• Journal of the Korean Chemical Society
• /
• v.40 no.12
• /
• pp.733-740
• /
• 1996

The rate constants for the hydrolysis of 4'-[N-(9-acridinyl)]-1'-(N-methanesulfonyl)-3'-methoxyquinonediimide(AMQD) were determined by ultraviolet visible spectrophotometer in water at $25^{\circ}C.$ The rate equation which could be applied over wide pH ranges were obtained. On the basis of pH-rate profile, Bronsted plot, hydrolysis product analysis, general base catalysis and substituent effect, the plausible hydrolysis mechanism was proposed: Below pH 3.00, the hydrolysis reaction was proceeded by the attack of water to 4'-position of quinonoid after protonation at nitrogen of acridinyl and between pH 3.00 and 9.00, the addition of water and hydroxide occurred competitively. However, above pH 9.00, the rate constants were dependent upon only the concentration of hydroxide ion.

• New & Renewable Energy
• /
• v.2 no.2 s.6
• /
• pp.69-74
• /
• 2006

본 연구는 페라이트의 Fe 양이온 일부를 Ni, Mn, Co등으로 치환하여 M-ferrite를 제조하여 열화학적 2단계 물 분해 반응의 특성을 비교 평가하였고, XRD, SEM, GC등의 분석으로 각 금속산화물의 특성을 확인하였다. M-ferrites 는 고상법으로 제조하였다. 각각의 M-ferrite에 대한 열적환원은 1573K 에서 진행하였고 물 분해 반응은 1273K 에서 실시하였다. 이 반응에서 생성된 가스는 전량 포집하여 GC를 통해 분석하였다. 반응 전후의 시료에 대하여 SEM, XRD를 분석하여 GC결과와 함께 금속산화물의 산화환원반응 특성을 고찰하였다. 그 결과로서 물 분해 반응 후 M-ferrite (M=Co, Ni, Mn)의 생성을 XRD를 통하여 확인할 수 있었고, 물 분해 반응과의 비교결과 격자상수의 증대가 M-ferrite내의 산소의 환원에 영향을 미치는 것을 알 수 있었다. SEM결과에서는 4cycle의 물 분해 반응 후 Mn-ferrite의 심한 sintering 현상을 확인 할 수 있었다.

• Journal of Food Hygiene and Safety
• /
• v.19 no.2
• /
• pp.97-103
• /
• 2004

The present study was performed to investigate photodegradation rate constants and degradation products of piperophos by the USEPA method. The pesticide was very stable in 16 days exposure of sunlight from October 3 to 22, 2003 and humic acid had no sensitizing effect on the photolysis of each pesticide in sunlight. In the UV irradiation test, piperophos was rapidly degraded as increasing UV intensity. In case of UV irradiation with TiO$_2$ and with TiO$_2$ powder amount, degradation of piperophos was slower than UV irradiation. In order to identify photolysis product, the extracts of degradation product was analyzed by GC/MS. The mass spectrum of photolysis product of piperophos was at m/z 166. It was suggested that the photolysis products of piperophos was O, O-dipropyl phosphorodithioate.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.261.1-261.1
• /
• 2014

지구상에 존재하는 모든 생물에 의해 배출되는 이산화탄소는 온실가스로써 산업혁명 이후 급격한 농도 증가로 인해 지구 온난화 등의 다양한 환경문제를 초래하고 있다. 지구 온난화의 가시화로 인한 각종 기후 협약 및 탄소배출권 등에 규제로 온실가스 감축의무부과가 확실해져 탈 석유기반 사회로 전환을 위한 이산화탄소를 처리하는 다양한 연구가 각국에서 활발히 진행 중이다. 본 연구에서 마이크로웨이브 플라즈마 토치를 이산화탄소 분해에 이용하게 되었고 그 목적은 이산화탄소가스를 마이크로웨이브로 가열하여 순수한 이산화탄소 플라즈마 토치를 발생함으로서 지구 온난화의 주범인 이산화탄소를 생산적으로 이용하기 위한 것으로 전자파를 발진하는 마그네트론으로는 3kW, 2.45GHz의 주파수를 사용한다. 마이크로웨이브 플라즈마 토치를 이용한 이산화탄소의 분해 시 생성되는 물질을 확인하기 위하여 이산화탄소의 열역학적 평형을 계산하였으며 또한 이산화탄소의 분해 반응의 준 평형상태에서의 속도상수를 이용하여 각 분해반응생성물들의 밀도비율을 계산하였고, 이를 일반화시켜 도시하였다. 위 과정을 통해 고온의 이산화탄소 토치는 탄화수소 연료를 1기압에서 개질할 수 있음을 알 수 있다. 예를 들어 메탄개질은 $CO_2+CH_4{\rightarrow}2CO+2H_2$의 반응식이 된다. 이때 엔탈피와 엔트로피 변화는 각 각 ${\Delta}H=247kJ/mole$과 ${\Delta}S=257J/mole/deg.$이며 이 반응에 대한 gibbs 자유에너지는 $G={\Delta}H-T{\Delta}S$로서 개질 자발반응이 일어나는 온도는 $T={\Delta}H/{\Delta}S=961K$가 된다. 그리고 탄화수소 개질에 참여하는 산소와 CO 라디칼의 밀도가 대단히 높다. 따라서 메탄개질은 이산화탄소 토치를 통하여 1기압에서 쉽게 이루어진다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.43-46
• /
• 2006

본 연구는 페라이트의 Fe 양이온 일부를 Ni, Mn, Co등으로 치환하여 M-ferrites를 제조하여 열화학적 2단계 물 분해 반응의 특성을 비교 평가하였고, XRD, SEM, GC등의 분석으로 각 금속산화물의 특성을 확인하였다. M-ferrites는 고상법으로 제조하였다. 각각의 M-ferrites에 대한 열적환원은 1573K에서 진행하였고 물 분해 반응은 1273K에서 실시하였다. 이 반응에서 생성된 가스는 전량 포집하여 GC를 통해 분석하였다. 반응 전후의 시료에 대하여 SEM, XRD를 분석하여 GC결과와 함께 금속산화물의 산화환원반응 특성을 고찰하였다. 그 결과로서 물 분해 반응 후 M-ferrite (M=Co, Ni, Mn)의 생성을 XRD를 통하여 확인할 수 있었고, 물 분해 반응과의 비교결과 격자상수의 증대가 M-ferrite내의 산소의 환원에 영향을 미치는 것을 알 수 있었다. SEM결과에서는 4cycle의 물 분해 반응 후 Mn-ferrite의 심한 sintering 현상을 확인 할 수 있었다.

• Journal of Food Hygiene and Safety
• /
• v.15 no.2
• /
• pp.144-150
• /
• 2000

The present study was peformed to determine the hydrolysis rate constants and degradation products of phosphamidon and proffnofos by the OECD method. Hydrolysis rate constants of phosphamidon in pH 4, pH 7, and pH 9 buffer solutions at 25 and 40$^{\circ}$C were 0.0020, 0.0022, 0.0049 and 0.0040, 0.0050, 0.0150, respectively. Hydrolysis rate of phosphamidon was accelerated by temprerature change under same pH conditions, and half-life of phosphamidon in pH 9 at 40。C was 3 times faster than that at 25。C. Hydrolysis rate of phosphamidon in alkaline solution(pH 9) was 2~4 times faster than that in acidic solution(pH 4) and neutral solution(pH 7) under same temperature. Hydrolysis rate constants of profenofos in pH 4, pH 7, and pH 9 buffer solutions at 25 and 40。C were 0.0022, 0.0047, 0.0860 and 0.0035, 0.0086, 0.1245, respectively. Hydrolysis rate of profenofos was accelerated by temprerature change under same pH conditions. Hydrolysis rate of profenofos in alkaline solution(pH 9) was 15~40 times faster than in acidic solution(pH 4) and neutral solution(pH 7) under same temperature condition, and half-life of profenofos was very fast within 8 hours. The hydrolysis rate of profenofos was faster than that of phosphamidon. In order to identify hydrolysis products, the extracts of degradation products were analyzed by GC/MS. The mass spectra of hydrolysis products of phosphamidon were at m/z 153 and 149, those of the profenofos were at m/z 208 and 240, respectively. The hydrolysis products of phosphamidon were O, O-dimethyl phosphate(DMP) and N, N-diethylchloroacetamide, and those of profenofos were 4-bromo-2-chlorophenol and O-ethyl-S-propyl phosphate.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.37 no.4
• /
• pp.308-314
• /
• 2017

This study was conducted with two ruminally cannulated Holstein steers to examine the effect of micronized and steam flaked corn on ruminal fermentation characteristics. The in situ dry matter degradability after 48 h incubation was the highest (P<0.05) at micronized corn (2.5 mm thickness) compared with steam flaked corn treatments. The steam flacked corn (3.3 mm thickness) was degraded lower (P<0.05) than the 2.9 and 3.1 mm thickness of steam flacked corn. Effective dry matter degradability and the rate of constant were the highest (P<0.05) at micronized corn (2.5 mm thickness) compared with steam flaked corns as well. The in vitro dry matter degradability after 48 h incubation was tended to higher (P=0.088) at micronized corn (2.5 mm thickness) than steam flaked corns, whereas there is no significantly difference between steam flaked corn treatments. Total volatile fatty acid concentration was higher at steam flaked corn (2.9 mm thickness) than micronized corn (2.5 mm thickness) and steam flaked corn (3.1 and 3.3 mm thickness). The acetate : propionate ratio was the highest (P=0.008) at steam flaked corn (2.9 mm thickness) and the lowest (P=0.008) at micronized corn (2.5 mm thickness). Total gas and methane production after 48h ruminal incubation was the highest (P=0.001) at micronized corn (2.5 mm thickness) compared with steam flaked corns. According to these results, the thickness of steam flaked corn as resulted corn processing is believed to do not affect methane production. However, further study is needed to better understand the present results to verify the correlation between corn processing method and their thickness on methane production using the same thickness corns by difference processing methods.

• Korean Journal of Environment and Ecology
• /
• v.32 no.6
• /
• pp.557-565
• /
• 2018

We examined the nutrient dynamics during the leaf litter decomposition rate and process of Pinus rigida and Pinus koraiensis in Gongju for 21 months from December 2014 to September 2016 as a part of National Long-Term Ecological Research Program in Korea. The remaining weight rate of P. rigida and P. koraiensis leaf litter was $58.27{\pm}4.13$ and $54.08{\pm}4.32%$, respectively, indicating that the P. koraiensis leaf litter decomposed faster than P. rigida leaf litter. The decay constant (k) of P. rigida leaf litter and P.koraiensis leaf litter after 21 months was 0.95 and 1.08, respectively, indicating that P. koraiensis leaf litter decayed faster than P. rigida leaf litter probably due to the difference of nitrogen concentration between the two. The C/N ratio of P. rigida and P. koraiensis leaf litter was 64.4 and 40.6, respectively, initially, and then decreased to 41.0 and 18.9, respectively, after 21 months. The C/P ratio of P. rigida and P. koraiensis leaf litter was 529.8 and 236.5, respectively, and then decreased to 384.1, 205.2, respectively, after 21 months. The contents of N, P, K, Ca, and Mg were 6.78, 0.83, 2.84, 0.99, and 2.59 mg/g, respectively, in the P. rigida leaf litter and 10.90, 1.87, 5.82, 4.79, and 2.00 mg/g, respectively, in the P. koraiensis leaf litter, indicating that the elements except the magnesium showed higher contents in P. koraiensis. After 21 months elapsed, remaining N, P, K, Ca, and Mg was 88.4, 77.6, 26.7, 50.5 and 44.5%, respectively, in decomposing P. rigida, and 114.4, 61.3, 7.6, 115.2 and 72.0%, respectively, decomposing P. koraiensis leaf litter.

• Journal of Food Hygiene and Safety
• /
• v.14 no.4
• /
• pp.339-345
• /
• 1999

The present study was performed to investigate photodegradation rate constants and degradation products of dichlorvos and methidathion by the USEPA method. The two pesticides were very stable in sunlight for 16 days from September 2 to 18, 1998 and humic acid had no sensitizing effect on the photolysis of each pesticide in sunlight. The photolysis rate was fast-est for methidathion, followed by dichlorvos in the presence of UV irradiation. Photodegradation rate constant and half-life of dichlorvos were 0.0208 and 33.3 min, respectively. Photodegradation rate constant and half-life of methidathion were 0.6789 and 1.0min, respectively. The two pesticides were degraded completely in the presence of UV irradiation and UV irradiation with TiO$_2$in about 3 hours. Therefore, it is suggested that UV treatment will be effective for the degradation of pesticides in the process of drinking water purification. In case of dichlorvos and methidathion, UV irradiation with TiO$_2$was more effective for degradation than W irradiation. In order to identify photolysis products, the extracts of degradation products were analyzed by GC/ MS. The mass spectrum of photolysis products of dichlorvos was at m/z 153, those of the photolysis of methidathion were at m/z 198 and 214, respectively. Photolysis products of dichlorvos was Ο, Ο-dimethyl phosphate(DMP), those of methidathion were Ο, Ο-dimethyl phosphorothioate(DMTP) and Ο, Ο-dimethyl phosphorodithioate (DMDTP).