• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.2
• /
• pp.33-40
• /
• 2020

Various studies have been conducted on the structural health monitoring using optical fiber. Optical fibers can be used to measure multiple and distributed strain. Among the optical fiber sensors, FBG sensor has advantages of dynamic response measurement and high precision, but the number of measurement points is limited. Distributed fiber sensors, represented by distributed Brillouin sensors, usually have more than 1000 measurement points, but the low sampling rate makes dynamic measurements impossible. In this study, a hybrid nerve sensor system using only the advantages of the FBG sensor and the distributed Brillouin sensor has been proposed. Laboratory experiments were performed to verify the proposed system, and the accuracy and reproducibility were verified by comparing with commercial sensors. Applying the proposed system, dynamic response ambient measurements are used to evaluate the global state of the structure. When an abnormal condition is detected, the local condition of the structure is evaluated by static response measurement using the distributed measurement system. The proposed system can be used for efficient structural health monitoring.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.10
• /
• pp.98-106
• /
• 1998

Efficient power transmission from a single mode fiber to a thin-film waveguide devices is one of the most fundamental and inevitable subject that should be first solved toward the realization of the integrated optic system. In this paper, fiber-waveguide coupling structure is considered and the large mismatch of field profiles at the fiber-waveguide interface is well avoided by using to the coupling guide which is intentionally developed on the top of the thin-film guuide. From the simulation, the taper-type structure are shown to be easier realizeable than the uniform one, since optical coupling between the guides in the latter has a stronger tolerance to the deviation of waveguide parameters.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.234-237
• /
• 2002

To detect external vibration signals on the latticed fence structure, distributed fiber optic sensor using Sagnac interferometer was fabricated and tested. The latticed structure fabricated with dimension of 170cm in width and 180cm in height, the optical fiber, 50m in length, distributed and fixed on the latticed structure. It was verified the sensitivity of the Sagnac interferometer using the PZT phase modulator. Fiber optic external vibration signal spplied to the latticed fence structure from 100Hz to several kHz. The interferometeric fiber optic sensor detected the excited vibration signal very effectively without any signal processing. The detected optical signals were compared and analyzed to the detected acclerometer signals.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.4
• /
• pp.534-543
• /
• 2000

In this paper, when the current optical communication system is used for the DWDM. The FBG filter for the DWDN is able to reduce the interferences between the adjacent channels. In this paper, therefore, we find the relection spectrums for the three types of induced index changes, that is, uniform, Gaussian apodized, and raised-cosine apodized. From the obtained result in this paper, we can see that uniform FBG does not fit, and that the smaller the maximum induced index change $\sigma$ is and the larger the value of parameter C in the raised-cosine apodized FBG and G in the Gaussian apodized FBG are the fitter they are on the narrow filter for DWDM.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.10a
• /
• pp.337-338
• /
• 2009

• Journal of Sensor Science and Technology
• /
• v.8 no.6
• /
• pp.440-447
• /
• 1999

Tensile stress loaded on smart composite structures and thermal stress occurred during the during process of the smart composite materials with embedded optical fiber sensors affect directly the mechanical behavior of the embedded optical fiber sensors within the smart composite structures. Stress distribution within the optical fiber sensors varies with respect to the stacking sequence of the composite laminate and the coating conditions of the optical fibers. The cracks occurred within the composite laminate affect not only the fracture of the composite laminate but also the fracture of the optical fiber sensors embedded within the composite laminate. In this study, firstly, stress distribution of the optical fiber sensors embedded within the composite laminate which is subjected to the tensile and thermal stresses was analyzed using Finite Element Method. And, secondly, the effect of the stacking sequence of the composite laminate and the coating conditions of the optical fiber sensors on the stress distribution of the optical fiber sensors was investigated. Finally, the effect of the crack occurred within the smart composite laminate on the fracture behavior of the optical fiber sensors was also observed through the tensile test.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.11
• /
• pp.1028-1036
• /
• 2007

A method for measurement and monitoring of mechanical loads in large slender structures such as wind turbine blade and tower is presented based on continuous strain data obtained from distributed fiber optic sensor. An experimental study was carried out on an aluminum cantilever beam. A static load test was performed and the calculated moment from the distributed fiber optic sensor agree well with the actual applied moment. A series of damages was inflicted on the beam, and vibration tests were carried out for each damage case. The estimated natural frequencies from the distributed fiber optic sensor for each damage case are found to compare well with those from a conventional accelerometer and a numerical analysis based on an energy method.

• Journal of Sensor Science and Technology
• /
• v.5 no.6
• /
• pp.15-24
• /
• 1996

In this study, as a part of the basic study for the application of optical fiber sensors to smart composite structures, the integrity of optical fiber sensors embedded within the composite structures was examined and then the laser signal transmitted through optical fiber sensors during the deformation of host structures was investigated. Firstly, it was found that bending test could be substituted for tensile test by comparing cumulative failure distribution based on weakest link theory and introducing the correction factor. Weibull parameters were obtained through the experiments and the correction factor was found to be applied to cumulative failure distribution derived from bending test. The integrity of embedded optical fiber sensors due to the thermal effect was evaluated by the comparison of the mean tensile strengths of cured and uncured optical fibers. Secondly, relationships between stress-strain curve obtained in tensile test of composite laminate and the intensity of laser signal transmitted through embedded optical fibers were examined and the possibility of the effective damage detection using optical fiber sensors was studied.

• Ecology and Resilient Infrastructure
• /
• v.7 no.3
• /
• pp.181-188
• /
• 2020

In this study, a temperature distribution sensing method using optical fiber was applied to a large-scale levee experiment, and the applicability of wide-area levee or embankment monitoring technology to observe the changes inside the levee was reviewed. The optical fiber was buried in a large-scale levee, and the temporal and spatial temperature changes were measured according to the water level changes in the reservoir. As the water level of the reservoir increased, the temperature of the embankment slope decreased, and as the infiltration progressed, a change in the spatial location of the temperature change was detected. The temperature change due to embankment infiltration varied depending on the time of the infiltration progress, and the change assumed to be the seepage line could be observed. This study has demonstrated that information about temperature changes inside the levee can be interpreted as the information on the locations that are judged to be relatively vulnerable, investigating the changes in the condition inside the levee.

• Ecology and Resilient Infrastructure
• /
• v.6 no.2
• /
• pp.120-127
• /
• 2019

Medium-scale levee experiments were performed to monitor the infiltration and failure of levee body by applying fiber optic temperature sensing. In this study, bio-polymer soil was spread in the levee slope to increase the strength and intensity. Therefore, the infiltration and failure by overflows were produced in a different way compared to general soil type of levees. This was also observed in the experiment data for temperature changes monitored by fiber-optic distributed temperature sensing system. Through the analysis of temperature changes at specific location by time, the location and initiation time for physical changes and infiltration in levee body could be identified based on temperature variation. In this experiment, the time of rapid changes in temperature was ahead in the inland slope rather than the forceland slope. It was corresponding to the levee failure sequence of first inland slope failure and then the forceland slope failure.