• Clean Technology
• /
• v.13 no.4
• /
• pp.300-307
• /
• 2007

The combustion characteristics of diffusion flame formed in the wake of a cylindrical stabilizer with varying fuel injection angle were studied. This study was performed by measuring the flame stability limits, lengths and temperatures of recirculation zones of flames, turbulence intensity in the wake of stabilizer, and concentration distribution of combustion gas, and by taking photographs of flames. The flame stability limits are dependent on fuel injection angle and main air velocity. The length and temperature of recirculation zone are dependent on fuel injection angle. As the length of the recirculation zone is decreased, the flame shows more stable behavior. The temperature of recirculation zone has a maximum value at the condition of theoretical mixture. The flame stability is enhanced when the temperature in the recirculation zone decreases. The turbulence intensity in the wake of stabilizer is independent of the fuel injection angle, but it is affected by stabilizer itself and main air flow condition. If the stabilization characteristics of flame is good, the concentration of $C_3H_8$ is high, but the concentration of $CO_2$ is low at the boundary of recirculation zone. The combustion characteristics of diffusion flame can be controlled by changing the fuel injection angles. The appropriate fuel injection angle should be selected to get high combustion efficiency, high load power, low environmental pollution, and clean combustion condition of fuel.

• Journal of Energy Engineering
• /
• v.10 no.3
• /
• pp.223-232
• /
• 2001

To study the stabilization characteristics of diffusion flame formed in the wake of a cylindrical bluff body with fuel injection, the flame stability limits, length and temperature of recirculation zone of flame, turbulence intensity distribution near the recirculation zone of flame were measured and analyzed. The length of recirculation zone is independent on main fuel injection quantity, but it is dependent on fuel injection angles, air stream velocity, and auxiliary fuel injection into recirculation zone. For diffusion flame, in general, the flame stabilization is deteriorated with increase of he length of recirculation zone, but if the turbulence generator is installed, the flame stabilization is improved with increase of the length of recirculation zone. The temperature of recirculation zone is dependent on fuel injection angles, auxiliary fuel injection into recirculation zone, turbulence generators, and it dependent on fuel injection angles, auxiliary fuel injection into recirculation zone, turbulence generators, and it has a maximum value at the condition of each theoretical mixture. In general, the more temperature of recirculation zone is low, the more flame is stable. But when the turbulence generator is installed, the more temperature of recirculation zone is low, the more flame is unstable. The turbulence intensity in the wake of bluff body is increased with increase of diameter or blockage ratio of grid. The more turbulence intensity is increased by installation of turbulence generator, the more flame is unstable. Finally, It is clear that the stabilization characteristics of diffuser flame can be controlled by some parameters such as fuel injection angles, auxiliary fuel injection into recirculation zone, turbulence generators.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.1130-1137
• /
• 1988

Heat transfer characteristics of evaporative transpiration cooling was investigated experimentally in the range of coolant mass flux, 0.002kg/m$^{2}$.sec~0.015m$^{2}$.sec. Glass beads, sand and copper particles were used as porous media and distilled water was used as a conant. The existence of evaporation zone was confirmed on this experimental conditions and its length increases with increasing article size and with decreasing mass flux. In order to get the low surface temperature, porous materials with high thermal conductivity is preferred when the panicle sizes are same, and small particles with low porosity is effective in case of the same material. Due to the relatively small coolant mass flux, evaporative transpiration cooling system could be stable by the capillary effect.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03a
• /
• pp.199-210
• /
• 2004

제주도는 신생대 제 3기~4기에 형성된 화산섬으로서 수십 차례에 걸친 화산분출에 의해 형성되어 지리적으로 한반도의 최남단에 위치하고 있으며, 우리나라에서 가장 큰 섬이다. 섬 중앙의 한라산을 중심으로 쉴드 화산체를 이루고 있는 제주도는 동서의 길이가 약 74km, 남북의 길이가 약 34km되며 섬 전체 면적이 1,825$\textrm{km}^2$인 타원형의 모양을 하고 있다. 제주도의 중앙부에는 수 차례의 화산활동에 의해 형성된 약 1,950m 높이의 한라산 정상에는 지름이 약 575$\times$400m, 깊이가 100m에 이르는 분화구가 있으며, 돔상의 조면암이 분화구 주변에 관입 되어 있다.(중략)

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.1
• /
• pp.62-68
• /
• 2009

The interaction between wall blowing and oxidizer flow can generate a very complicated flow characteristics in combustion chamber of hybrid rockets. LES analysis was conducted with an in-house CFD code to investigate the features of turbulent flow without chemical reactions. The numerical results reveal that the flow oscillations at a certain frequency exists on the fuel surface, which is analogous to those observed in the solid propellant combustion. However, the observation of oscillating flow at a certain frequency is only limited to a very thin layer adjacent to wall surface and the strength of the oscillation is not strong enough to induce the drastic change in temperature gradient on the surface. The visualization of fluctuating pressure components shows the periodic appearance of relatively high and low pressure regions along the axial direction. This subsequently results in the oscillation of flow at a certain fixed frequency. This implies that the resonance phenomenon would be possible if the external disturbances such as acoustic excitation could be imposed to the oscillating flow in the combustion chamber.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.213-221
• /
• 1998

The investigation regarding the ignition system of a plasma jet explored by using a constant volume vessel. The purpose of this study is to elucidate relation between the characteristics of the configuration and jet ejection of plasma jet plug, when the sub energy were supplied at plasma jet ignition system. From the results of a visualization by the schlieren system, the jut ejection for plasma jet ignition are depended on the jet plug configuration and sub energy, but the configuration of plasma jet plug is more influenced than the sub energy on the plasma jet ejection. And the plasma jet ignition strongly influences upon the combustion enhancement than the conventional spark ignition.

• Tunnel and Underground Space
• /
• v.21 no.4
• /
• pp.320-327
• /
• 2011

In this study, for stemming effect in blast of the mortar block body, the crushed granite sand as fine aggregate, which is waste rock obtained at the ○○ limestone mine, was investigated to compare with stemming materials such as sea sand, river sand, clayed soil and water can be acquired easily at the field. The mortar block body was manufactured with the dimensions of 50 cm width, 50 cm length and 70 cm height. The direct shear and sieve separator test were performed, and the properties of friction resistance were analyzed by the extrusion test for five stemming materials. Axial strain of steel bar and ejection velocity of stemming materials due to the explosive shock pressure in blasthole with the stemming length of 10 cm and 20 cm in the mortar blast test were measured by the dynamic data acquisition system. Among stemming materials, axial strain showed the largest value at the crushed granite sand as fine aggregate, and the ejection velocity was the smallest value at the stemming of water. The results has shown correlate with harden unit weight in blasthole, particle size distribution, shear resistance, and extrusion strength of stemming materials. The ejection velocity of stemming material at the mouth of blasthole and the axial strain of steel bar in the inside of blasthole tend to be inversely proportional to each other, represent exponentially.

• Journal of the Speleological Society of Korea
• /
• v.25 no.26
• /
• pp.15-28
• /
• 1991

제주도는 세계에서 이름난 화산동굴의 보고라고 불리운다. 그 동굴의 길이 뿐만 아니라 그 규모 그리고 그들 동굴속에 간직하고 잇는 갖가지 동굴의 지형지물등 하나하나가 모두 세계 제1 또는 세계적인 것들에 많이 집중분포하고 있기 때문이다. 한편 환산동굴은 용암동굴 핏트동굴 리프트동굴등으로 다시 세분하기도 하는데 핏트동굴은 리프트 동굴과 같이 매우 희귀한 것으로 화산활동때에 분출된 화산탄이나 화산력 그밖에 화산계등으로 되는 화도가 그대로 남아서 수직구멍을 이루고 있는것을 가리킨다. 그리고 리프트동굴이란 마그마가 화도속에 가득차 있는 상태이면서도 수직동굴이 남아 있는 경우를 말한다.(중략)

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.240.1-240.1
• /
• 2014

대기압 플라즈마 제트 장치에 주입되는 기체의 유량 변화에 따른 방전 특성을 유체역학적으로 해석하였다. 장치에 주입되는 기체의 유량 변화는 레이놀즈수에 의한 유체 흐름의 상태 변화와 베르누이 정리에 의한 압력 변화를 동반한다. 유리관에 주입되는 기체의 레이놀즈수가 Re<2000이면 층류이며 Re>4000이면 난류, 2000

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.228-228
• /
• 2011

바늘형 전극과 컵형 전극을 사용한 대기압 플라즈마 제트 장치의 플라즈마 분출 특성을 조사한다. 바늘형 전극은 원통형 주사기 바늘을 사용하였다. 컵형 전극은 냉음극 형광 램프의 전극을 사용하였다. 방전 가스는 Ar을 사용하고 가스의 유량은 3 lpm이다. 구동 전원은 DC-AC 인버터를 사용하고 구동 주파수는 40 kHz이다. 방전 전압-전류 특성과 전류별 플라즈마 방출 길이를 측정한 결과, 원통형 바늘보다 컵형 전극이 방전 개시 전압이 낮았으며 동일 전류에서 플라즈마 방출 길이가 더 길다.