• Membrane Journal
• /
• v.27 no.6
• /
• pp.487-498
• /
• 2017

In this study, pervaporation performances of water/methanol and water/butanol mixture were evaluated using zeolite 4A membranes manufacutred by FINETECH by experimental works and numerical modeling. Permeation and separation characteristics, such as flux and separation factor, were analyzed by gas chromatography (TCD) and liquid nitrogen traps. Experiments have shown that water is selectively separated from a mixture of water and methanol (separation factor up to approximately 250) and water and butanol (separation factor up to approximately 1,500). Generalized Maxwell Stefan (GMS) theory was implemented to predict pervaporation behaviors of water/alcohol mixtures and diffusional coefficients of zeolite layer were obtained through parameter estimation using $MATLAB^{(R)}$ optimization toolbox. Since the pore size of zeolite 4A are much larger than kinetic diameter of water molecules and smaller than those of methanol and butanol, zeolite 4A membranes can be applied to in situ water removal process such as membrane reactors or hybrid reaction-dehydration process.

• Journal of the Korean Institute of Gas
• /
• v.8 no.1 s.22
• /
• pp.37-47
• /
• 2004

Pressure swing adsorption (PSA) process using CMS as an oxygen purifier was developed to produce high purity oxygen over $99\%$ with high productivity. The cyclic performances such as purity, recovery, and productivity of PSA process were compared experimentally and theoretically under the non-isothermal condition. A binary ($O_2$/Ar 95:5 vol.$\%$) and two kinds of ternary ($O_2/Ar/N_2$ 95:4:1 and 90:4:6 vol.$\%$) mixtures were used as feed gases. The developed process with the consecutive two blowdown steps produced the oxygen with $99.8\%$ purity and $56\%$ recovery from $95\%$ oxygen containing feed. However, in the feed with $90\%$ oxygen, the $O_2$ Purity was decreased up to $97.3\%$. In addition, because the cyclic performances of the suggested process was significantly affected by the diffusion rate, the non-isothermal model with the the modified LDF model was applied for the process simulation. The concentration-dependent rate parameter of the applied rate model was incorporated with the Langmuir isotherm.

• Microbiology and Biotechnology Letters
• /
• v.48 no.2
• /
• pp.215-222
• /
• 2020

The marine microorganism PX-1, which can hydrolyze xylan, was isolated from coastal sea water of Jeju Island, Korea. Based on the 16S rRNA gene sequence and chemotaxonomy analysis, PX-1 was identified as a species of the genus Aestuariibacter and named Aestuariibacter sp PX-1. From the culture broth of PX-1, an extracellular xylanase was purified to homogeneity through ammonium sulfate precipitation and subsequent adsorption chromatography using insoluble xylan. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis and gel filtration chromatography estimated the molecular weight of the purified putative xylanase (XylA) as approximately 64 kDa. XylA showed xylanase activity toward beechwood xylan, with a maximum enzymatic activity at pH 6.0 and 45℃. Through thin-layer chromatographic analysis of the xylan hydrolysate produced by XylA, it was confirmed that XylA is an endo-type xylanase that decomposes xylan into xylose and xyloligosaccharides of various lengths. The K_m and V_max values of XylA for beechwood xylan were 27.78 mM and 78.13 μM/min, respectively.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.10a
• /
• pp.70-72
• /
• 1998

1. 서론 : 최근에 폐수나 지하수 및 음용수에 존재하는 휘발성 유기화합물(Volatile Prganic Compound, VOC)는 심각한 환경오염이 주범이 되고 있다. 이러한 문제를 해결하는 방법으로 흡착, 증류, air stripping 등의 여러 가지 분리기술이 제시되어 왔다. 그러나 전통적인 방법들은 분리된 오염물질이 제2의 상으로 전이된다는 점에서 또 다른 분리공정을 필요로 하는 단점을 지니고 있다. 이에 반해 투과증발공정은 추가적인 분리과정이 없이 효율적으로 오염된 물속의 유기용매를 제거한다는 점에서 많은 관심을 모으고 있다. 이미 알려진 이러한 VOC 제거에는 소수성이면서 고무상인 고분자가 우수한 특성을 가지는 것으로 밝혀졌고 그 중에서 실록산계 고분자가 아주 효과적인 것으로 알려져 있다. 그러나 이러한 실록산계 고분자는 기계적 강도가 약하여 필름의 박막형성능력이 떨어지는 것으로 알려져 있어 이러한 단점을 보완하기 위해 가교구조의 도입이나 공중합체의 구조를 도입하는 연구가 많이 수행되어 왔다. 이러한 연구의 한 방법으로 실록산-아미드공중합체를 이용하여 투과증발에 적용한 연구는 수행되어 왔다. 이들의 제막방법으로 주로 실록산다이아민/방향족다이아민의 비를 달리하거나 실록산다이아민의 분자량의 변화를 달리하면서 실록산-이미드 블록 또는 그래프트중합체를 제조하는 방법을 사용하였다. 이 실험에서는 주로 실록산-이미드의 비율이 낮아지면 유기용매의 선택성에서 물의 선택성으로 바뀌는 percolation point가 관찰되며 이것은 실록산-이미드의 비율이 낮을수록 물속의 유기용매의 제거에 유리하다는 것을 보여준다. 이에 따라 실록산다이아민과 다이안하이드라이드만을 사용한 실록산이미드막이 추천되나 여기에 대한 투과특성연구는 전혀 이루어지지 않았다.정육점이었고 백화점과 재래닭 사육장에서 직접구입도 하고 있었다. 구입 동기는 가족들이 좋아하고 영양가를 생각한다가 62%였으며 구입정보는 주위사람의 권유로 구입하고 있었다. $\bigcirc$ 구입할 때 중점적으로 살펴보는 사항은 신선도와 순수재래종 여부, 위생상태였다. 한편 소비자가 언제나 구입할 수 없다는 의견이 85.2%나 되어 원활한 공급과 시장조성이 아직 정착되지 않고 있었다. $\bigcirc$ 현재 유통되고 있는 재래종닭은 소비자 대부분이 잡종으로 인식하고 있었으며, 재래종과 일반육계와의 구별은 깃털색, 피부색, 정강이색등 외관상으로 구별하고 있었다. 체중에 대한 반응은 너무 작다는 의견이었고, 식품으로의 인식도는 비교적 고급식품으로 인식하고 있다. $\bigcirc$ 재래종닭고기의 브랜드화에 대한 견해는 젊고 소득이 높은 계층에서 브랜드화의 필요성을 강조하고 있다. $\bigcirc$ 재래종달걀의 소비형태는 대부분의 소비자가 좋아하였으나 아직 먹어보지 못한 응답자가 많았다. 재래종달걀의 맛에 대해서는 고소하고 독특하여 차별성을 느끼고 있었다. $\bigcirc$ 재래종달걀의 구입장소는 계란판매점(축협.농협), 슈퍼, 백화점, 재래닭 사육 농장등 다양하였으며 포장단위는 10개를 가장 선호하였고, 포장재료는 종이, 플라스틱, 짚의 순으로 좋아하였다. $\bigcirc$ 달걀의 가격은 200원정도를 적정하다고 하였으며, 크기는 (평균 52g)는 가장 적당하다고 인식하고 있으며, 난각색은 대부분의 응답자가 갈색을 선호하였다. $\bigcirc$ 재래종달걀의 구입시 애로사항은 믿을수 없고, 구입장소를 몰라서, 값

• Membrane Journal
• /
• v.23 no.5
• /
• pp.352-359
• /
• 2013

In the present study, $CO_2$ permeation through a hydrophilic NaY zeolite membrane was studied under permeate evacuation mode for $CO_2$ single gas, $CO_2-N_2$ and $CO_2-O_2$ binary mixtures, and $CO_2-N_2-O_2$ ternary mixture. It was reconfirmed that the $CO_2$ permeation was governed by surface diffusion and the $CO_2$ selectivity was induced from blocking effect of adsorbed $CO_2$ molecules. The $CO_2$ permeance measured in permeate evacuation mode was much lower than that done in He sweeping mode, but was comparable to that obtained under feed pressurization mode. The NaY zeolite membrane showed a considerable $CO_2$ separation for $14%CO_2-80%N_2-6%O_2$ mixture : $CO_2$ permeance was about $1{\times}10^{-7}mol/m^2secPa$ and $CO_2$ selectivity was more than 10. Therefore, it was concluded that NaY zeolite membrane was one of promising membranes for post-combustion CCS process.

• Clean Technology
• /
• v.27 no.4
• /
• pp.325-331
• /
• 2021

In this study, bio-carbons were produced by activation process from unused biomass (Grade 3 wood pellet and spent coffee grounds) to determine the removal performance of formaldehyde and acetaldehyde. The activation experiments were conducted in a fixed bed reactor using CO₂ as an activation agent. The temperature of the activation reactor and input of CO₂ were 900 ℃ and 1 L min^-1 for all the experiments. The maximum BET surface area of about 788 m² g^-1 was obtained for bio-carbon produced from Grade 1 wood pellet, whereas about 544 m² g^-1 was achieved with bio-carbon produced from spent coffee grounds. In all the experiments, the bio-carbons produced were mainly found to have micro-porous nature. A lower ash amount in raw material was favored for the high surface area of bio-carbons. In the removal test of formaldehyde and acetaldehyde, the bio-carbon produced from spent coffee grounds showed excellent adsorption performance compared with woody biomass (Grade 1 wood pellet and Grade 3 wood pellet). In addition, the comparative experiment of commercial impregnated activated carbon and bio-carbon produced from spent coffee grounds was conducted. In terms of formaldehyde removal performance, the commercial impregnated bio-carbon was excellent, while bio-carbon produced from spent coffee grounds was excellent in acetaldehyde removal.

• Journal of Life Science
• /
• v.30 no.12
• /
• pp.1128-1139
• /
• 2020

Over recent years, it has become evident that food and agricultural products are easily contaminated by fungi of Aspergillus, Fusarium, and Penicillium due to rapid climate change, which is not only a global food quality concern but also a serious health concern. Owing to consumers' interest in health, resistance to preservatives such as propionic acid and sorbic acid (which have been used in the past) is increasing, so it is necessary to develop a substitute from natural materials. In this review, the role of lactic acid bacteria as a biological method for controlling the growth and toxin production of fungi was examined. According to recent studies, lactic acid bacteria effectively inhibit the growth of fungi through various metabolites such as organic acids with low molecular weight, reuterin, proteinaceous compounds, hydroxy fatty acids, and phenol compounds. Lactic acid bacteria effectively reduced mycotoxin production by fungi via adsorption of mycotoxin with lactic acid bacteria cell surface components, degradation of fungal mycotoxin, and inhibition of mycotoxin production. Lactic acid bacteria could be regarded as a potential anti-fungal and anti-mycotoxigenic material in the prevention of fungal contamination of food and agricultural products because lactic acid bacteria produce various kinds of potent metabolic compounds with anti-fungal activities.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.4
• /
• pp.463-475
• /
• 2020

Presence of microplastics in soil and groundwater has recently been reported and environmental concerns are raised as to the plastic pollution. In the subsurface environment, clay minerals and metal oxide minerals are commonly found as finely dispersed states. Because the minerals have high sorption capacities for diverse pollutants, interactions with mineral surface play an important role in the transport of microplastics in groundwater. Accordingly, environmental mineralogy investigating the interactions between microplastics and mineral surfaces is the essential research area to understand the fate and transport of microplastics in the subsurface environment. The microplastic-mineral surface research requires molecular- to nano-scale analyses to be able to probe the relatively weak interactions between them. The current report introduces a nano-scale analysis tool called quartz crystal microbalance (QCM) that can measure the sorbed/desorbed mass of nanoplastics on mineral surfaces at the level of a few nanograms (~10-9 g). This report briefly reviews the main principles in the QCM measurement and discusses applications of QCM to the environmental mineralogy research.

• Clean Technology
• /
• v.26 no.4
• /
• pp.311-320
• /
• 2020

In this study, the photocatalytic degradation of rhodamine B (RhB), methyl orange (MO) and methylene blue (MB) was carried out under visible light irradiation using CdS and CdZnS/ZnO photocatalysts prepared by a simple precipitation method. This study focused on examining the effect of physicochemical properties of dye and photocatalyst on the reaction pathway of photocatalytic degradation. The prepared photocatalysts were characterized by XRD, UV-vis DRS and XPS. Both the CdS and CdZnS/ZnO photocatalysts exhibit an excellent absorption in the visible light and the UV light regions. It was observed that the photocatalytic degradation of MO proceeds via the same reaction mechanism on both the CdS and CdZnS/ZnO photocatalysts. However, the photocatalytic degradation of RhB and MB was found to proceed through a different reaction pathway on the CdS and CdZnS/ZnO catalysts. It is interesting to note that MB dimer was formed on the CdS catalyst at the beginning of the photocatalytic reaction, while the MB monomer was degraded during the overall photocatalytic reaction on CdZnS/ZnO. The above results may be mainly ascribed to the difference of band edge potential of the conduction band in the CdS and CdZnS/ZnO semiconductors and the adsorption property of dye on the catalysts.

• Journal of the Korean Electrochemical Society
• /
• v.26 no.4
• /
• pp.71-79
• /
• 2023

In this study, we employed anionic, cationic, and nonionic surfactants for the hydrophilization of porous substrates used in the fabrication of pore-filling membranes. We investigated the extent of hydrophilization based on the type of surfactant, its concentration, and immersion time. Furthermore, we used the hydrophilized substrates to produce pore-filling anion exchange membranes and compared their ion conductivity to determine the optimal hydrophilization conditions. For the ionic surfactants used in this study, we observed that hydrophilization progressed rapidly from the beginning of immersion when the applied concentration was 3.0 wt%, compared to lower concentrations (0.05, 0.5, and 1.0 wt%). In contrast, for the relatively larger molecular weight non-ionic surfactants, smooth hydrophilization was not observed. There was no apparent correlation between the degree of hydrophilization and the ion conductivity of the anion exchange membrane. This discrepancy suggests that an excessive hydrophilization process during the treatment of porous substrates leads to excessive adsorption of the surfactant on the sparse surfaces of the porous substrate, resulting in a significant reduction in porosity and subsequently decreasing the content of polymer electrolyte capable of ion exchange, thereby greatly increasing the electrical resistance of the membrane.