• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.22-28
• /
• 1986

기관의 성능에 영향을 주는 인자로서는 외적인자(outside factor), 작동인자(operating factor) 및 설계인자(design factor)의 3가지로 나눌 수 있다. 작동인자로서는 기관회전수, 공기연료비, 점화 시기 또는 분사시기 등이면 설계인자로서는 행정체적, 압축비, 흡배기계통의 구조 및 치수, 냉각 방식 등으로 기관에 따라 고유한 값을 가지는 인자이다. 그러나 외적인자인 대기조건 즉 대기 압력, 대기온도 및 대기습도는 계절, 지역 및 기상조건에 따라 달라지므로 이것에 따라 기관이 흡입하는 공기의 압력, 온도 및 습도는 변화하게 된다. 그러므로 대기조건의 변화에 따라서는 기관작동인자인 공기연료비에도 영향을 미치게 할 것이고 또한 연소상태의 변화로 유효압축비 에도 영향을 미치게 할 것이므로 대기상태의 변화는 곧 바로 기관 출력의 변화를 초래하게 될 것이다. 그러므로 같은 운전조건에서의 기관출력도 대기상태의 변화에 따라 변화하게 되므로 임의의 대기 상태에서 측정한 기관출력을 표준대기상태의 기관출력으로 환산해서 평가할 필요가 생긴다. 이것을 일반으로 출력수정(output correction)이라 하고 있으며 각 나라마다 공업규격 또는 기타규격으로 출력정식을 제정하고 있다. 예를 들면 K.S.B 9102, SAE J816B, B.S. 765, DIN 70020, JIS B 8013등이다. 이들 출력수정식들은 많은 문제점을 가지고 있으므로 종래의 출 력수정식으로 출력수정을 하여도 정확하게 맞지 않은 경우가 많다. 출력수정에 관한 문제는 수 10년전부터 많은 연구자에 의하여 연구되고 거론되어 왔으나 과거의 연구자들이 제안하고 거론 되어 왔으나 과거의 연구자들이 제안하고 있는 출력수정식, 또는 규격으로 정하고 있는 출력수 정방법은 어느 것이나 실용상 만족스러운 것이 아직 없다. 그러므로 본 자료는 스파아크 점화 기관의 흡기습도에 관한 출력수정의 문제를 실험적으로 수행한 실험적 출력수정방법에 의한 것과 종래의 출력수정방법에 의한 것과를 비교 검토하였다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.1108-1111
• /
• 2009

Auto Pilot is the system which move automatically the vessel through locating operation mode to automatic after entering operating course using a electronic chart or plotter. And water jet is the a propulsion system that make a power to push the vessel through spouting the accelerated water which is absorbed by the hole in the bottom of vessel. The water jet receive the effect of the depth of water lowly, it's acceleration efficiency is higher under high speed and have an advantage on vibrating and floating sound, so it's demand is increasing as new propulsion system. However, the signal systems of auto pilot and water jet are different, we need the system to interface between each system. We designed the interface that efficiently digital feed back control embedded module between auto pilot and water jet system in this paper.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.4
• /
• pp.10-15
• /
• 2010

Light gas guns have a large number of applications in various fields of engineering. A two-stage light-gas gun can produce an extremely high pressure in a very short interval of time. In general, the two-stage light-gas gun is made up of a high pressure tube, a compression tube and a launch tube, each stage being separated by diaphragms. This can be employed efficiently in the application of ultra-high pressure liquid jets. In the present study, experiments are carried out to investigate the projectile velocity and pressure behavior in the tubes according to the pressure changes at the frist diaphragm opening. In the present study result was found that the rupture pressure of the first diaphragm has a dominant influence on piston acceleration.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.3
• /
• pp.189-195
• /
• 2019

In this work, the flow and combustion characteristics using a 3-D numerical simulation was evaluated for a shale gas fueled combustor in a commercial class gas turbine. The Standard k-e turbulence model, 2 step methane oxidation mechanism, Finite rate/Eddy dissipation reaction model, DTRM radiation model were employed and validated well at the baseline condition (Natural Gas, Pilot Ratio 0.2). Based on the validated models, the combustion characteristics of shale gas was evaluated for three pilot ratios cases. It was found that NOx concentrations for all shale gas cases were less than the that for city gas, which imply that, at the selected PRs, the condition for combustion stability is satisfied. In addition, for higher PR, whereas the average temperatures at the exit are the same, the NOx increases. It means that diffusion combustion portion increases due to the higher PR.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.69-77
• /
• 2020

A quasi one-dimensional multi-phase reaction flow analysis code is developed for the performance analysis of liquid pintle thrusters. Unsteady flow field, droplet evaporation, finite reaction and film cooling models are composed as the major models of the performance analysis. The droplet vaporization takes account of Abramzon's vaporization model, and the combustion employs a flamelet model based on detail chemical reactions. Shine's model is applied for the film cooling calculation. To verify each model, the Sod shock tube, single droplet vaporization, kerosene droplets combustion, and film length are evaluated.

• Journal of Powder Materials
• /
• v.28 no.4
• /
• pp.310-316
• /
• 2021

The effects of different spray angles (90°, 85°, 80°) on the microstructure and mechanical properties of a Y₂O₃ coating layer prepared using the atmospheric plasma spray (APS) process were studied. The powders employed in this study had a spherical shape and included a cubic Y₂O₃ phase. The APS coating layer exhibited the same phase as the powders. Thickness values of the coating layers were 90°: 203.7 ± 8.5 ㎛, 85°: 196.4 ± 9.6 ㎛, and 80°: 208.8 ± 10.2 ㎛, and it was confirmed that the effect of the spray angle on the thickness was insignificant. The porosities were measured as 90°: 3.9 ± 0.85%, 85°: 11.4 ± 2.3%, and 80°: 12.7 ± 0.5%, and the surface roughness values were 90°: 5.9 ± 0.3 ㎛, 85°: 8.5 ± 1.1 ㎛, and 80°: 8.5 ± 0.4 ㎛. As the spray angle decreased, the porosity increased, but the surface roughness did not show a significant difference. Vickers hardness measurements revealed values of 90°: 369.2 ± 22.3, 85°: 315.8 ± 31.4, and 80°: 267.1 ± 45.1 HV. It was found that under the condition of a 90° angle with the lowest porosity exhibited the best hardness value. Based on the aforementioned results, an improved method for the APS Y₂O₃ coating layer was also discussed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.4
• /
• pp.53-58
• /
• 2021

Based on surrogate model, a hydrocarbon mixture was analyzed by visualizing the impinging break up mechanism in subcritical and supercritical conditions. Decane and methylcyclohexane with different critical pressures and temperatures were selected as experimental fluids. The impinging injector was installed inside the chamber, and the spray was visualized through a speed camera in subcritical and supercritical conditions. The injection condition of the mixture and chamber was kept constant at Pr(P/P_c) = 1, and Tr(T/T_c) was increased from 0.48 to 1.02. As Tr increased, the spray angle increased, and the sheet length decreased as the properties of the mixture reached each critical point. In addition, when the mixture approached the near critical point, it was shown that the change in density gradient was largely observed out of the impinging break up mechanism.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.5
• /
• pp.41-50
• /
• 2023

This study reviewed the liquefaction reinforcement and ground reinforcement methods widely used domestically and abroad through construction method characteristics and analyzed the economic feasibility and reinforcement efficiency of each reinforcement method. The analysis results were used to evaluate the applicability of the appropriate reinforcement method for the liquefaction reinforcement of new and existing structures. As a result of evaluating the applicability of the reinforcement method based on the economic feasibility and reinforcement effect of each reinforcement method, the compaction method, which secures the construct ability by applying large equipment, is advantageous when reinforcing a new structure, and the low-fluidity mortar injection method (C.G.S method) and the high-pressure injection method (J.S.P method) are considered appropriate in the existing structure.

• Journal of Digital Convergence
• /
• v.20 no.1
• /
• pp.155-163
• /
• 2022

The ecology of Korean Production Industry has been changing rapidly. Small & medium size independent production companys have been shrinking in market share while big size production companys are taking larger share than before. This study intends to show the dramatic change of the ownership in Korean production industry and the consequencies. When considering positive development of production industry, small & medium size independent production companys should play important roles but the environment of the industry is not easy for them. The implication of this study is that small & medium size independent production companys have to search for survival strategies to adapt environmental change.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.229-229
• /
• 2021

최근 이상기상으로 국지성 집중호우가 빈번하게 발생함에 따라 토사유출에 의해 피해가 증가하고 있다. 급경사 사면을 갖는 교란산지와 개발지의 경사면은 토양침식 위험에 노출되어 있다. 특히 지표유출수의 집중흐름에 의한 세류발달은 세류간침식에 비해 많은 토양침식과 토사유출을 발생시킨다. 이러한 급경사 사면에서의 세류발달에 대한 수리학적 메터니즘과 한계조건을 파악하고자 강우와 유입수 모의를 통한 토양침식 실험을 수행하였다. 강우와 유입수의 상호작용에 의한 세류발달의 특성과 토사유출량 증가를 파악하고자, 강우량의 증가와 유입수 유무에 따른 실험이 이루어졌다. 강우강도의 범위는 100~140mm/hr이고, 유입수는 170ml/s 이였다. 유입수량은 합리식으로 계산하였으며, 토양상자 상단에서 균등분사식으로 유입되었다. 세류발달의 수리학적 특성치를 취득하기 파악하기 위해, 염료주입 지표수 거동에 대한 동영상을 판독하였다. 세류발달은 유입수가 없는 경우 3분 이내 그리고 유입수가 있는 경우 30초 이내에 발생하였다. 토양상자내의 평균 유속범위는 7.83~29.27 cm/s 이였다. 실험에서 발달된 세류는 15분경과 후부터 평형상태를 유지하였다. 경사실험조건별로 세류 차수분석을 위해 각 세류의 최대길이, 폭, 넓이를 측정한 결과 세류의 차수는 강우만 있는 경우 1~2차로 발달하였으며, 유입수가 있을 때는 2~3차로 발달하였다. 지표유출이 증가하면서 세류발달의 개수는 줄었지만 규모는 더 크게 나타났다. 세류가 발달하는 시점의 한계유속은 10~20cm/s 범위인 것으로 파악되었다. 지표유출이 증가하면서 세류의 발달도 더 심화되지만, 동일한 강우에 일정시간동안 노출되면서 세류는 평형상태가 되어 더 이상 침식이 활발하게 진행되지는 않았다. 유입수가 있는 조건에서 수량은 약 2배가 증가하였지만, 토사유출량은 세류확장에 의해 약 4배가 증가하는 것으로 나타났다.