• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.8-8
• /
• 1998

액체 추진제를 사용하는 연소기관내의 연소 불안정 현상에 대하여 수치적인 해석을 수행하였다 비정상 다차원 다상 유동장에 대한 Eulerian-Lagrangian 방법에 기반을 두고 수학적으로 모델 하였으며 속도-압력-밀도에 대한 결합메커니즘은 개선된 PISO 알고리즘을 사용하여 처리하였다. 연소실의 기하학적 형상 및 추진제의 분무조건이 액체 연료 추진기관의 연소 불안정 현상에 미치는 영향을 체계적으로 해석하였으며 액체 추진제의 증발 특성이 연소 불안정 현상의 Driving Mechanism에 미치는 영향을 상세히 분석하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.39-48
• /
• 2006

In this research, in order to study the spray, combustion, and emission characteristics of the common rail DME engine, the target engine was disassembled, and 3D CAD file was constructed using a 3D measurement machine and a rapid prototyping machine. Using the obtained 3D geometry, fine moving meshes are generated, and three dimensional non-steady turbulence flow field and combustion phenomenon including spray were numerically analyzed. As a result, IMEP of DME and diesel in medium and high speed revolution showed similar performance. As the DME fuel start to burn in spray area, the vaporized fuel rapidly spreads squish area in low speed revolution. In the case of DME engine, CO and NOx are relatively consistent with experiment results. It was found that the break-up, evaporation, collision model of DME fuel need to be properly adjusted through matching the characteristics of fuel and injector for further improvement.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1763-1773
• /
• 1991

본 연구에서는 포화수증기와 공기의 혼합기내에서 분무수적으로의 열 및 질량 전달률을 계산하기 위하여 수적의 부분혼합모형과 비혼합모형에 대하여 수적내 과도온 도분포의 해석해를 적용성이 보장되면서도 계산상의 어려움이 수반되지 않는 형태로 구하기 위하여 수적내부의 열전도해석에 있어서 적분법을 적용하였다. 적분법으로 얻어지는 과도온도분포의 해는 유한차의 다항식으로 표시되어 비혼합모형인 경우 각시 간 구간의 경계에서의 온도분포가 연속성을 유지하면서 물성치들의 온도에 대한 종속 성이 쉽게 고려되고 계산도 용이한 형태이다. 본 보에서 제시하는 해석결과의 적용 성을 조사하기 위하여 완전혼합모형을 포함하는 세가지 수적모형들에 대한 계산결과들 로부터 얻어진 시간변화에 따른 수적의 무차원 체적평균온도변동을 유효한 실험결과들 과 비교, 검토하였으며, 부분혼합모형에 대하여 혼합기의 압력, 수적의 초기온도, 혼 합기 속에 포함되어 있는 수증기의 체적분율, 수적의 초기크기, 수적의 초기속도 및 분사각도가 주위혼합기로부터 수적으로 전달되는 열 및 질량전달에 미치는 영향을 조] 사하고 도출된 대표적인 검토 결과를 제시하였다.

• Journal of ILASS-Korea
• /
• v.20 no.1
• /
• pp.14-19
• /
• 2015

Recently, R&D demand for environmental friendly vehicle has rapidly increased due to its global environmental issues such as global warming, energy and economic crisis. Under this situation, the most realistic alternative way for environmental friendly vehicle is a clean diesel vehicle. The common-rail fuel injection system, as key technology of clean diesel vehicle, consists of a high pressure pump, common-rail, high pressure fuel line and electronic control injector. In common-rail high-pressure fuel injection system, high pressure wave of injection system and geometry of injector elements have a major effects on high-pressure fuel spray. Therefore, in this study, the numerical model was developed for analysis about the common-rail fuel pressure pulsation by using AMESim code. We could secure stability of common-rail high-pressure fuel injection system through optimal design of fuel line.

• Journal of ILASS-Korea
• /
• v.13 no.4
• /
• pp.212-219
• /
• 2008

To develop the twin-fluid atomizer having the excellent performance of painting, the spray characteristics of how a wide area can be painted efficiently by one time spraying were studied in this paper. Spray phenomena are affected by the many factors determining the spray field such as the spraying pressure of gas, the spraying pressure and viscosity of liquid paints, the opening duration of needle valve, the design dimension of nozzle, and so on. As the results of experiments, these factors affecting on spray characteristics were suggested as followings; 1) The optimum spraying pressure of gas was $0.015{\sim}0.02\;kPa$, and the appropriate spraying pressure of liquid paint was 0.01kPa, In these situations, the setting up pressures must be compensated as much as the losing amount of pressure because a decompression occurred when operating valves. 2) The duration of opening the needle valve must be sustained for $1{\sim}2$ seconds to inject gas after spraying the liquid paint. This operating of the needle valve was necessary to avoid the affect on the changing of liquid column length, and to prevent the droplet deposit at the initial time of spraying. 3) The spray tip penetration was gained form the experimental equation, and the effective spraying angle was $85^{\circ}{\pm}5^{\circ}$ just at he appropriate spraying pressure of gas. The distribution of the area sprayed had the variation in $350{\pm}50\;mm$ because of the spraying pressure of gas, the its distance from the spray tip, and the lift of the needle valve.

• Fire Science and Engineering
• /
• v.30 no.6
• /
• pp.111-117
• /
• 2016

The present study examined the free surface flow of a liquid sheet near a sprinkler head using a Computational Fluid Dynamics (CFD) model and considered the feasibility of the empirical model for predicting the initial spray characteristics of the sprinkler head through a comparison of the CFD results. The CFD calculation for a simplified sprinkler geometry considering the nozzle and deflector were performed using the commercially available CFD package, CFX 14.0 with the standard $k-{\varepsilon}$ turbulence model and theVolume of Fluid (VOF) method. The predicted velocity of the empirical model at the edge of deflector were in good agreement with that of the CFD model for the flat plate region but there was a certain discrepancy between the two models for the complex geometry region. The mean droplet diameter predicted by the empirical model differed significantly from the measured value of the real sprinkler head. On the other hand, the empirical model can be used to understand the mechanism of droplet formation near the sprinkler head and predict the initial spray characteristics for cases without experimental data.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.3
• /
• pp.237-243
• /
• 2015

In this study, the effects of the mixing ratio of emulsified fuel on the droplet evaporation and spray behavior characteristics were analyzed. A surfactant comprising span 80 and tween 80 mixed at a 9:1 ratio was used for the emulsified fuel. The fuel and surfactant were mixed at a ratio of 3:1 for the emulsified fuel. In addition, considering the mixing ratio of the surfactant, the mixing ratio of $H_2O_2$ in the emulsified fuel was set as EF (emulsified fuel)0, EF2, EF12, EF22, EF32, and EF42. To observe the evaporation characteristics, droplets of the emulsified fuel were dropped on a heating plate and observed using scattered light and a Schlieren system. In addition, to analyze the effect of the $H_2O_2$ mixing ratio, the behavior characteristics of the evaporative free spray were investigated in the mixing ratio range of EF0 to EF22 using a constant volume chamber with heaters. Consequentially, it was found that in the case of EF22, the free spray development of the emulsified fuel was faster than that of EF0 (diesel only) because of the promotion of the evaporation due to the phase change in the peroxide contained in the emulsion fuel.

• Journal of the Korean Society of Visualization
• /
• v.3 no.2
• /
• pp.14-20
• /
• 2005

내연기관 연소는 난류유동, 분무, 연소, 열전달의 복합적인 현상으로서 열역학적 해석이 주류를 이루어 왔으나 컴퓨터의 발전에 따라 효율 개선과 공해 저감을 목표로 전산유체해석 기법이 적극적으로 도입되고 있다. 내연 기관 연소의 근간을 형성하는 난류 연소 모델링의 기본 개념으로서 가솔린엔진에서의 예혼합연소와 디젤엔진에서의 확산연소에 대한 영역조건평균(zone conditional averaging) 모델과 조건평균닫힘(conditional moment closure) 모델에 대해 설명하였으며 $NO_x$와 soot 예측에 대한 적용과 엔진응용 사례를 소개하였다.

• Proceedings of the KSR Conference
• /
• 2006.05b
• /
• pp.214-220
• /
• 2006

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.5
• /
• pp.1-9
• /
• 2017

The cryogenic nitrogen spray of a swirl injector has been numerically investigated using three dimensional LES turbulence model to analyze the dynamic characteristics under supercritical condition. To predict the precise nitrogen properties under supercritical condition, SRK equation of state, Chung's method for viscosity and thermal conductivity and Takahashi's correlation based on Fuller's theory for diffusion coefficient are implemented. The complex flow structures due to interaction between flow field and acoustic field are observed inside and outside the injector under supercritical condition. FFT, POD, and DMD techniques are employed to understand the coherent structures. By implementing the FFT, the dominant frequencies are identified inside and outside the injector. The coherent flow structures related to the dominant frequencies are visualized using the POD and DMD techniques. In addition, the DMD provides the damping coefficient which is related with the instability prediction.