• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.691-691
• /
• 2013

최근 휴대용 전자기기의 전원으로서 가장 널리 사용되고 있는 리튬 이차 전지는 우수한 에너지 밀도, 낮은 자가방전 속도로 인한 비 메모리 효과, 높은 작동전압으로 다양한 전자기기뿐만 아니라 미래형 자동차산업 및 항공산업 분야에서도 점차 사용 빈도가 증가하고 있다. 현재 리튬 이차 전지의 음극물질로 널리 사용되고 있는 흑연의 경우 초기 용량 감소가 크고 이론적인 최대용량(372 mAhg-1, LiC6)이 낮다는 문제가 있어 다양한 대체물질의 연구가 진행되고 있다. 그 중에서도 Si는 Li과 반응하여 Li4.4Si합금을 형성하며 높은 이론용량을 갖고 상용화된 전지의 전압(~3.7 V)보다 0.3 V정도 밖에 낮지 않기때문에 재료의 개발과 함께 바로 사용화 할 수 있다는 장점이 있다. 그러나 Si의 경우 금속 자체로 사용되는 경우 Li 이온이 삽입되어 Li4.4Si형성 시에 310%의 부피 팽창을 일으키게 되어 분쇄반응(pulverization)을 일으키고 충 방전에 따라 급격한 용량 감소를 야기한다. 본 연구에서는 이러한 문제점을 해결하기 위하여 RF 마그네트론 스퍼터링을 이용하여 보다 간단한 방법으로 Si층 사이에 수 나노의 Al층을 삽입하여 Si 입자의 부피 팽창으로부터 오는 응력을 상쇄시켜 높은 방전 용량 특성과 우수한 수명 특성을 동시에 구현하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.186.2-186.2
• /
• 2014

최근 친환경 에너지에 대한 관심이 증폭되면서 리튬이차전지에 대한 연구가 활발히 진행되고 있다. 특히 음극(anode) 물질의 경우 기존의 흑연(graphite)보다 이론적 용량이 약 10배 이상 높은 실리콘(Silicon)에 대한 관심이 매우 높다. 하지만 Si의 경우 리튬 충전거동 시 400% 이상의 부피팽창으로 몇 번의 충전/방전 싸이클(cycle)에 전극이 파괴되는 문제점을 지니고 있다. 이를 극복하기 위해 Si 나노선이 고려되고 있다. 우수한 전극특성을 갖는 Si 소재를 개발하기 위해서는 원자단위에서 Si 나노선의 리튬 충전 메커니즘을 살펴보는 것이 매우 중요하다. 하지만 기존의 시뮬레이션 기법으로는 Si 나노선의 볼륨팽창에 관한 메커니즘과 리튬 충전과정에서의 상변화(결정질에서 비정질) 과정을 설명하기는 기술적으로 매우 힘들다. 고전적인 분자동역학 방법의 경우 실제 나노스케일을 고려할 수 있지만, empirical potential로는 원자들간의 화학반응을 제대로 묘사할 수 없다. 한편 양자역학에 기반을 둔 제일원리방법의 경우 계산의 복잡성으로 현재의 컴퓨터 환경에서는 나노스케일에서 원자들의 동역학적인 거동을 연구하기 매우 힘들다. 우리는 이러한 문제를 해결하기 위해 실제 나노스케일에서 원자간 화학반응을 예측할 수 있는 Si-Li 시스템의 Reactive force field를 개발하였고, 분자동역학 계산방법을 이용하여 Si 나노선의 Li 충전 메커니즘을 규명하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.4 no.4
• /
• pp.404-408
• /
• 2003

This paper discusses the physical properties of permeable high quality concrete using blast furnace slag or steel slag as a part of aggregate. In the case of steel slag, aging treatment was adopted to prevent the volume expansion. With high range water reducing agent, the concrete using slag aggregate showed compressive strength up to 24MPa at the age of 28 days and the water permeability of the concrete was over the level of 0.1 m/s in this experiment. Also, there was no expansion problem in the concrete substituted with aged slag as a part of aggregate.

• Journal of the Korean Society for Railway
• /
• v.12 no.5
• /
• pp.811-818
• /
• 2009

An estimation method of the fallout volume of a tunnel under construction is proposed based on an empirical method called bulking factor. For this, the main causes of the tunnel fallout are investigated and the scale of the fallout which is not accessible is considered. The calculated height of the fallout area is compared with borehole core data and the accuracy and efficiency of the proposed method is demonstrated. Another experimental approach on the detection of a progressive cracking around the tunnel fallout is provided based on an acoustic emission method. From the field tests near the tunnel fallout, it is shown that additional progressive cracking of the reinforced area is not foreseen and the effectiveness of the reinforcement is proven.

• Journal of the Korean earth science society
• /
• v.34 no.6
• /
• pp.470-478
• /
• 2013

There have been a number of observed precursors of volcanic activities- such as volcanic earthquake, surface inflation, specific volcanic gas emission, temperature of hot spring- at Mt. Baekdusan since 2002. We identified the increase of the volume of magma chamber beneath Mt. Baekdusan as we observed an inflation trend of vertical and horizontal surface displacement around Cheonji caldera lake by using precise leveling data from 2002 to 2009. The surface displacement trend changed to deflation in 2010, and the trend changed to inflation again after a while. Utilizing the data of inflated surface (46.33 mm) on the northern slope of Mt. Baekdusan from 2002 to 2003, we calculated the volume change of magma chamber beneath the Mt. Baekdusan. The volume change was about 0.008 $km^3$ ($7.7-8.0{\times}10^6m^3$) from 2002 to 2003. It indicated that a new magma (0.008 $km^3$) injected to the magma chamber 5 km below Mt. Baekdusan.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.11
• /
• pp.97-106
• /
• 2020

Swelling properties and shear strength behavior of MgO-Sand mixtures with hydration procese of MgO are compared according to different MgO contents (W_MgO/W_Total=0, 30, 50, 70, 100%) in this study. The specimens are prepared by mixing with crushed MgO refractory bricks and silica sand. After hydration, the particle size and the specific gravity of MgO were decreases. Through microstructure observation and X-ray diffraction analysis, it is confirmed that MgO changes from the cubic structure of Periclase to the hexagonal cubic structure of Brucite after hydration. As the MgO content increases, both swelling rate and swelling pressure of the mixtures increase. W_MgO/W_Total=30% specimen shows relatively low swelling pressure and swelling rate because produced Mg(OH)₂ mainly fills the pores between sand particles. However, in the case of MgO more than 50%, swelling pressure and swelling rate increase significantly because Mg(OH)₂ fills the pores of sand particles at first and then either pushes out sand particles or Mg(OH)₂ particles after filling the pores. As a result of the direct shear test, before hydration, the mixtures show a dilative behavior on high MgO contents and a contractive behavior on low MgO contents. However, after hydration, the behavior of all mixtures changes to contractive behavior. The threshold fraction of fine (i.e., Mg(OH)₂) contents of the hydrated MgO-Sand mixtures reveals approximately 60% compared with normalized shear strength.

• Applied Chemistry for Engineering
• /
• v.19 no.4
• /
• pp.397-401
• /
• 2008

To verify model adaptation and flexibility, non-isothermal simulation for perlite expansion has been carried out. Temperature-dependent perlite properties are applied to energy equations for bubble temperature change and perlite melt temperature gradient. Bubble temperature is changed with volume change, water evaporation, and heat flux from melt. Temperature gradient of perlite melt is affected by decreasing bubble temperature. As a result, prediction model and code have been developed below 1100 K with 5% accuracy. At 1100~1400 K, lower 7% accuracy has been obtained from the calculation results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.12
• /
• pp.14-24
• /
• 2018

Several typical hyper-elastic constitutive models that encompass both conventional and advanced ones were investigated for the application of instability problems, including the biaxial tension of a rubber patch and inflation of spherical or cylindrical balloons. The material models included the neo-Hookean model, Mooney-Rivlin model, Gent model, Arruda-Boyce model, Fung model, and Pucci-Saccomandi model. Analyses can be done using membrane equations with particular strain energy density functions. Among the typical strain energy density functions, Kearsley's bifurcation for the Treloar's patch occurs only with the Mooney-Rivlin model. The inflation equation is so generalized that a spherical balloon and tube balloons can be taken into account. From the analyses, the critical material parameters and limit points were identified for material models in terms of the non-dimensional pressure and inflation volume ratio. The bifurcation was then identified and found for each material model of a balloon. When the finite element method was used for the structural instability problems of rubber-like materials, some careful treatments required could be suggested. Overall, care must be taken not only with the analysis technique, but also in selecting constitutive models, particularly the instabilities.

• The Journal of the Korea Contents Association
• /
• v.12 no.7
• /
• pp.358-367
• /
• 2012

The importance of physical changes in volume due to changes in temperature has been known for more than a century by the petroleum industry. To examine whether there are any differences between the economic effect of automatic temperature compensation and that of installation cost. The results of the analysis show that there are no ineffective in automatic temperature compensation installation. Analysis showed the increase of price oil will impact negatively on the automatic temperature compensation, appropriate level of economic cost and economic benefit should be calculated for the policy implementation in the future's study.

• Applied Chemistry for Engineering
• /
• v.16 no.5
• /
• pp.628-634
• /
• 2005

Zirconia-alumina polymer precursor was prepared from zirconium acetylacetonate (ZA). paluminium nitrate (AN), polyethylene glycol (PEG), and ethyl alcohol via an organic-inorganic solution technique. The thermal properties and viscosity of the polymer precursor were measured by differential scanning calorimetry (DSC), thermograbimetric analyzer (TGA), and dynamic viscometer. The vigorous exothermic reaction with volume expansion occurred at $140^{\circ}C$. The volume expansion was caused by abrupt decomposition of the organic group in metal compounds and the metal ions-PEG reaction. The evidences for these reactions were confirmed by FT-IR and $^{13}C$ solid NMR results. The peak intensity at N-O, O-H and C=C decreased with increasing temperature. This indicated that the decomposition of metal compounds and the metal ions-PEG reaction occurred during the vigorous exothermic reaction. At $800^{\circ}C$ for 2 h, the porous powders transformed to the crystalline $ZrO_2-Al_2O_3$ composites.