• Journal of the KSME
• /
• v.33 no.7
• /
• pp.661-670
• /
• 1993

스트레인 게이지를 이용한 응력측정 방법 및 응력 측정시의 오차 발생의 원인에 대해서 설명하 였고 현재 많이 사용되고있는 스트레인 게이지식 로드셀의 원리 및 구조에 대해서도 설명하였다. 스트레인 게이지를 이용하여 변형도를 측정할 경우 1% 이내의 정확도를 유지하는 것이 가능하나 측정된 변형도로부터 응력을 계산할 경우 재료상수들의 부정확성으로 인하여 5% 정도의 오차가 발생할 수 있다. 스트레인 게이지를 이용한 응력 측정값은 부착위치에서의 값이므로 구조물의 최대 응력을 측정하고자 할 경우 구조물의 응력 상태를 제대로 파악하지 못하면 큰 오차가 발 생할 수 잇다. 따라서 정확한 측정을 위해서는 정확한 게이지 작업 기술과 함께 하중에 대한 대상물의 거동을 파악하는 기술 습득이 요구된다. 스트레인 게이지식 로드셀을 직접 설계 및 제작하기 위해서는 용량, 정밀도, 설치 공간, 사용조건 등을 고려하여 감지부의 형상, 감지부의 재질, 스트레인 게이지의 종류, 부착 방법, 보상회로 구성방법, 보호 케이스의 부착 여부 등을 결정하여야 하고 제작이 완료된 후 힘 표준기 등으로 교정검사를 실시하여 사용하여야만 정확한 측정을 기대할 수 있다.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.5
• /
• pp.157-164
• /
• 1997

일반적으로 콘크리트와 철근간의 경계면을 나타내는 유한요소법에는 균열의 부근에서 발생하는 부착열화 현상을 고려하지 않고 있다. 이것은 균열 부근에서 과도한 부착을 초래하고 , 국소 변형과 균열의 진전에도 영향을 준다. 본 연구에서는 철근콘크리트 구조물의 균열부근에서 일어나는 부착거동의 변화를 고려한 비선형 부착응력-미끄럼 모델을 제안하였다. 철근과 콘크리트간의 경계면에는 링크요소를 이용하였고, 링크의 특성은 철근을 가로지르는 균열의 상태에 따라 변하도록 조정하였다. 균열의 형성상태를 정량화하고, 부착거동을 두 포락선 1) 균열로부터 충분히 떨어진 위치에서의 부착상태를 모델링한 외연포락선, 2)횡균열면에 있어서의 부착상태를 모델링한 내연포락선의 사이에 변이시키기 위하여 비국소적 손상도 개념을 도입하였다. 이 방법의 유효성을 알아보기 위하여 편재하중을 받는 T형 교각의 실험 및 해석결과를 제시하였다. 제안된 모델의 결과를 실험결과와 비교하여 본 모델의 유용성을 검증하였다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.3
• /
• pp.202-208
• /
• 2014

For evaluating basic structural behavior of HVFA (High Volume Fly Ash) concrete, several tests are performed considering different ratios of fly ash replacement and structural evaluation regarding compressive strength, elasticity modulus, stress-strain relationship, and bond strength is also performed. Test results show that elasticity modulus of HVFA concrete has close relationships with compressive strength and fly ash replacement ratio. The ultimate strain shows slight difference from domestic design code. On the other hand, there are no differences between general concrete and HVFA concrete for elasticity modulus and bond strength.

• Journal of the Korea Concrete Institute
• /
• v.21 no.3
• /
• pp.337-345
• /
• 2009

The purpose of this study is to investigate the shear strengthening effectiveness of the beams strengthened with near surface mounted (NSM) and external bonded (EB) CFRP strips. A total of nine concrete beams were made and tested. From this study, it was found that the shear stiffness and strength of the beams strengthened with NSM and EB strips were significantly improved compared to the control beam. Failure of the beam strengthened with NSM and EB strips was initiated by shear cracks, propagated diagonally to the adjacent epoxy grooves without crossing the epoxy and finally sudden diagonal crack connecting the point of application of load and flexural crack was occurred. For the beam strengthened combined with NSM and EB CFRP strips, the tensile strains in the NSM CFRP strips were observed in the range of 0.35% to 0.45% and strains with EB strips were measured about 0.3%.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.76-85
• /
• 2017

In this study, to evaluate the mechanical properties of fiber-reinforced cement composites by strain rate, hydraulic rapid loading test system was developed. And compressive and tensile strength of the hooked steel fiber and polyamide fiber reinforced cement composite were evaluated. As a result, the compressive strength, strain capacity and elastic modulus were increased with increasing strain rate. The effect of compressive strength by type and volume fraction of fibers was not significant. The dynamic increase factor(DIF) of the compressive strength was higher than that of the CEB-FIP model code 2010 and showed a trend similar to that of ACI-349. The tensile strength and strain capacity were increased with increasing strain rate. The hooked steel fibers were drawn from the matrix. The tensile strength and strain capacity of hooked steel fiber reinforced cement composites were increased as the strain rate increased. The tensile strength and deformation capacity of the fiber reinforced cement composites were increased. And, hooked steel fibers were drawn from the matrix. On the other hand, because the bonding properties of polyamide fiber and matrix is large, polyamide fiber was cut-off with out pullout from matrix. The strain rate effect on the tensile properties of polyamide fiber reinforced cement composites was found to be strongly affected by the tensile strength of the fibers.

• Journal of Korean Association for Spatial Structures
• /
• v.8 no.6
• /
• pp.95-100
• /
• 2008

The object of this paper is to verify possible to monitor the deformation of cable in the tensegrity structure. Also, always monitoring system of tensegrity structure using Fiber Bragg Grating Sensor is described. We carry out experiments with measuring deformation of cable in the tensegrity structure based on loading conditions. In the result of experiment, the Fiber Bragg Grating Sensors shows accurate response to the loading conditions. Therefore, we can make sure the possibility of Fiber Bragg Grating Sensor in health monitoring of the cable structure like tensegrity structure.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.3
• /
• pp.157-165
• /
• 2003

The paper deals with the rupture strain estimation of fiber sheets. The experimental study involved tensile testing of 120 fiber sheet specimens and bending testing of 72 concrete beams strengthened with various types of fiber sheets(carbon, glass, and aramid fiber). Concrete beams have 3 types of reinforcement ratios. Rupture strains of fiber sheet specimens are determined by tensile tests to be a little less than the tensile failure strain by the catalog, independently on the number of fiber sheet layers. It is shown that the rupture strain of fiber sheet bonded to reinforced concrete beam is not constant, but decreases as the fiber sheet layer increases. Based on these results, the rupture fiber sheet strain is estimated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.253-256
• /
• 2008

Although researches on the beams strengthened with Fiber reinforced Polymers (FRPs) have recently been conducted around the world, there are few researches on the beams with FRPs under a sustained load. This paper presents the behavior of the beams with Carbon Fiber Reinforced Polymers (CFRP) and Glass Fiber Reinforced Polymers (GFRP) under a sustained load during 300 days. Strains of steel and FRP reinforcement were measured in order to investigate the behavior of the beams. Additionally, Adjusted Effective Modulus Method (AEMM) and Ghali and Farve's method were used to predict increase in the stress and strain caused by creep and shrinkage. Through the experiment, it was found that the beam with CFRP is more effective than the beam with GFRP in terms of flexural strengthening. Compared with analytical results, it was indicated that strains of tension steels were overestimated, whereas strains of compression steels were underestimated.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.14 no.1
• /
• pp.125-132
• /
• 2010

In the recent construction industry, an external strengthening method using fiber reinforced polymers has been widely used. Since reinforced concrete structures strengthened with fiber reinforced polymers are always under sustained loads, influence of creep and shrinkage on the structures is inevitable. Due to the creep and shrinkage, behaviors of the structures, such as deflection, deformation, recovery capability, strength and so on are also under the influence of creep and shrinkage. Thus, in order to estimate efficacy, creep recovery and residual strength of FRP strengthened RC beams, long-term flexural experiments and static flexural experiments were carried out. As the result of the experiments, FRP strengthened RC beams were very effective in terms of deflection control. Furthermore, the strengthened beams had higher immediate deformation recovery than immediate deformation. Through the static flexural experiments, it was shown that the CFRP strengthened beam had high residual strength. It seems that the sustained loads did not affect bond and residual strength of the beams.

• Restorative Dentistry and Endodontics
• /
• v.35 no.5
• /
• pp.395-400
• /
• 2010

The development of adhesive dentistry has allowed that the crown fragment reattachment can be another option in the treatment of crown fracture. However, additional crown lengthening procedure or extrusion of the tooth may be necessary in the treatment of crown root fracture because subgingival fracture line in close proximity to the alveolar bone leads to challenges for restorative procedure and the violation of the biologic width. This case report presents a modified crown fragment reattachment technique of crown root fracture with pulp exposure, which was done without additional crown lengthening procedures. After the endodontic treatment, the patient was treated using a post insertion and the fragment reattachment technique, which made it possible to preserve the space for the biologic width and maintain a dry surgical field for adequate adhesion through the modification of the fractured coronal fragment. Since a coronal fracture was occurred and reattached afterward, it was observed that the coronal fragment was well maintained without the additional loss of periodontal attachment through 2-year follow up.