• Membrane Journal
• /
• v.27 no.2
• /
• pp.182-188
• /
• 2017

Sulfonated poly(arylene ether sulfone) (SPAES)-3-mercaptopropyl silica gel (3MPTSG) composite membranes with improved oxidative stability were prepared for polymer electrolyte fuel cell application. It has been reported that ether part of main chain of aromatic hydrocarbon based membranes were weak to radical attack to decrease membrane durability. In this study, the hydrophilic inorganic particles were introduced by minimizing a decrease in ion conductivity and increasing an oxidative stability. The composite membranes were investigated in terms of ionic conductivity, ion exchange capacity (IEC), FT-IR, TGA and contact angle, etc. As a result, increasing amount of the 3MPTSG resulted in decrease in proton conductivities and water uptakes at 100% R.H. but enhanced thermal and oxidative stabilities.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.1
• /
• pp.31-37
• /
• 2009

Hybrid ballast for field emission lamp with CNT (carbon nano tube) emitter is proposed. Hybrid ballast consists of a high voltage dc part and hi-polar pulse generation part. Field emission lamp with CNT lamp is composed of three electrodes (anode, gate, and cathode). High voltage dc part is for anode and gate and hi-polar pulse generation part is for gate and cathode in CNT triode respectively. The experimental results demonstrate that the proposed topology is good for driving CNT lamp. To protect the lamp and ballast, OCP (Over Current Protection), OVP (Over Voltage Protection), and OTP (Over Temperature Protection) are added and the experimental results demonstrate that the proposed method is good for driving field emission lamp with CNT emitter.

• Korean Journal of Optics and Photonics
• /
• v.12 no.2
• /
• pp.103-108
• /
• 2001

In this paper, we designed and made the scanned point detecting system for 3-dimensional measurement of the light emitted from plasma display panel (PDP) , and we measured and analyzed 3-dimensional light emitted from a real PDP by using this scanned point detecting system. The scanned point detecting system has a point detector with a pinhole. The light emitted from the source at the in-focus position can pass through the pinhole and be collected by detector. The light from other sources at outof-focus positions is focused at points in front of or behind the pinhole, and thus it is intercepted by the pinhole. Therefore, we can detect light information from a particular point of a PDP cell of 3-dimensional structure. We know the electric field distribution inside the PDP cell from the 3-dimensionallight intensity distribution measured by using the scanned point detecting system. As the Z axial measurement increases, the intensity of light detected increases and intensity of light detected on the inside edge of the ITa electrode is larger than outside edge of the ITa eletrode and gap of the ITa electrodes. Also, as the measurement point moves from one barrier rib to another, the detected light is weaker near to the barrier ribs than at the center between the barrier ribs. The emitted light is concentrated at the center between barrier ribs. ribs.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.2
• /
• pp.784-789
• /
• 2012

In this paper, a number of anode and reference electrodes that are installed around the target anti-corrosion objects to monitor, appropriate to your situation of a fixed potential and polarization methods can be applied automatically in the system was developed. In particular, this system was configured with a remote electric anti-corrosion automatic control device that have automatically adjust function to uniformal anti-corrosion in all parts of target objects, a corrosion monitoring device to perform the function of corrosion potential detection and a web-based operating program to perform the function of real-time monitoring, control and prediction. Using this system, by preventing oxidative corrosion phenomena can maximize the life of the target anti-corrosion objects.

• Journal of Energy Engineering
• /
• v.8 no.1
• /
• pp.23-33
• /
• 1999

용융탄산염 연료전지의 대형화에 관한 기본 기술을 확립하기 위하여 전극의 유효면적이 625 $\textrm{cm}^2$인 단위전지를 20단 적층한 내부 분배형 용융탄산염 연료전지 스택을 제작하고 그 성능을 살펴보았다. 연료로 72% H2/18% CO2/10% H2O를 , 산화제로는 70% air/30% CO2의 혼합 기체를 사용하여 운전한 결과 전류밀도가 150 mA/$\textrm{cm}^2$이고 연료 및 산화제의 이용율이 0.4일 때, 스택 전압이 16.62 V로 1.56 kW의 높은 초기출력을 나타내었다. 스택 내 분리판에서의 온도 분포는 가스 흐름 방향으로 온도가 증가하였으며 스택출력이 높아질수록 가스 배출 부분의 온도가 상승하였다. 스택 내 각 단위전지간의 성능 분포는 균일하지 않았으며, 가스이용율에 따라 그 편차가 증가하였다. 연속 운전 300시간 후부터 스택의 성능이 감소하였으며, 그 원인을 분석한 겨로가 탄소 석출과 부식 생성물에 의한 전기 단락 때문으로 밝혀졌다. 본 연구를 통하여 anode 출구에서의 가스 조성을 분석함으로써 전기 단락에 의한 전압 손실량을 계산하는 기법을 확립하였다. 또한 본 연구에서 얻은 결과를 통하여 향후 스택의 대형화와 장수명화에 대한 대책을 제시하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.2
• /
• pp.250-254
• /
• 2003

A film bulk acoustic resonator (FBAR) device for 2 GHz radio frequency (RF) bandpass filter application is presented. This FBAR device consists of an aluminum nitride (AlN) film sandwiched between top(Al) and bottom(Au) electrodes and an acoustic multilayer reflector of a silicon dioxide/tungsten (SiO2/W). The A/N film deposited using a RF sputtering was observed to have small columnar grains with a strongly preferred orientation towards c axis. In addition to a high quality factor (4300), a large return loss of 37.19 dB was obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.286-287
• /
• 2006

Electrowetting display (EWD) is one of the strong candidates for electronic paper like display (EPD). However, in the conventional EWD, the oil movement occurs in random direction so that we can observe irregular distribution of contracted oil in the operation. To realize colorful display and achieve a fast response time, oil movement in the pixel should be directed in a specific direction. In this paper, we report the result of oil contraction with specified direction which is achieved by patterned electrode. From the experiments, we find that the oil movement depends on the portion of etched electrode area and study other influencing factors of patterned electrode on the oil movement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.162-163
• /
• 2006

XLPE is used to insulator for Ultra High Voltage power cable. It is easy to processing also has a good insulating property. The study for diagnosis of lifetime and improvement is proceeding continuously. In this paper, it is investigated partial discharge distribution according to slope of needle electrode 0, 20, $40^{\circ}$. Applied voltage is 0.5 [kV/s] by step form for inception voltage. As the result of study, we conformed that increase of slope led to reduce of discharge number and total discharge quantity.

• Journal of the Korean Chemical Society
• /
• v.36 no.5
• /
• pp.674-678
• /
• 1992

An instrument is described that can obtain directly the whole capacitance vs. potential curve and accurately even in dilute solutions using positive feedback for IR correction. Applying a small (7∼10 mV) triangular signal, controlled rectification of the resulting square wave using sample-and-hold circuit allows one to plot the corrected double layer capacitance over a wide potential range. Several illustrations involving the improved performance characteristics of its applicability are given and its limitations discussed.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1523-1525
• /
• 1996

Partial discharges(PD) in air insulated electric power systems cause power loss, produce interfering electromagnetic radiation, and can indicate incipient failure. An understanding of PD in air gap is clearly important. The Wavelet transformation is an extended method of fourier transformation. The fourier method is a powerful tool for signal analysis, but it can't include informations for time. However tile wavelet transformation analysis can include on the informations of time and frequency at the same time. In this paper we apply the wavelet transformation to the PD signals in needle-plane air gap for tile purpose of analysis of developing aspects of PD. We can analyze the developing aspects of PD, namely, PD current, repetition rates, width of pulse distribution region, pulseless region and frequencies distribution of PD pulses.