• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.10
• /
• pp.1794-1800
• /
• 2008

This paper presents a method of constructing the digital logic switching functions using PLA. First of all, we propose a MIN and MAX algebra arithmetic operation based on the Post algebra. And we discuss the T-gate which is used for realization of the MIN and MAX algebra arithmetic operation. Next, we discuss the MIN array and MAX array which are basic circuit of the PLA, also we discuss the literal property. For the purpose of the design for the digital logic switching functions using PLA, we Propose the variable partition, modular structure design, literal generator, decoder and invertor. The proposed method is the more compactable and extensibility.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.290-290
• /
• 2021

급격한 도시화 및 기후변화로 인한 물순환체계가 왜곡됨에 따라 자연수재해 피해가 급증하고 있어 대응방안으로 저영향개발(Low Impact Development, LID) 기법이 대두되고 있다. LID 요소 기술 중 하나인 식생저류지는 도시 유역내에서 발생하는 유출수를 저류 및 침투하여 우수유출수와 비점오염원으로 인한 오염저감 효과를 지니고 있는 LID 요소이다. 본 연구에서는 식생저류지의 우수유출수의 정량적 저감효과를 분석하기 위해 수문해석 프로그램인 K-LIDM(Korea Low Impact Development Model)을 이용하여 유역 내 식생저류지 배열과 저류용량에 따른 유출저감 효과를 분석하였다. 강우시나리오는 부산지점의 10년, 30년 발생빈도에 대하여 60분, 120분, 180분 확률강우시나리오를 선정하여 적용하였다. 모델링 분석결과 식생저류지 배치에 따라 5 ~ 15 % 이상의 유출저감효과가 산정되었으며, 식생저류지 저류용량에 따라 20 % 이상의 유출저감 효과가 산정되었다. 첨두유출 도달시간은 1.13 ~ 1.86배를 지연하는 결과가 산정되었다. 결과를 통해 식생저류지의 배열과 저류용량에 따라 유출량 저감효과와 첨두유출 도달시간에 영향을 미침을 알 수 있었다. 추후에 다른 매개변수인 식생저류지의 저류깊이, 지반의 침투능 및 유출부의 직경 등 여러 매개변수들을 고려한 연구를 수행한다면 식생저류지의 정량적 물순환 평가가 수행될것으로 사료된다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.2
• /
• pp.163-168
• /
• 2001

Due to aging, adhesively bonded and riveted aircraft lap joints can contain distends, cracks around rivet holes, fatigue induced flaws, and corrosion. It is required for the safety of aircraft to inspect these defects through the whole region of mint in rapid speed. Bond quality or adhesively bonded and riveted aluminum lap splice joints is investigated using non-contact remote ultrasonic nondestructive evaluation (NDE). Non-contact ultrasonic tests are performed using laser generation and air-coupled transducer detection. A Q-switched Nd:YAG laser and a periodic transmission mask are used to generate a selected Lamb mode. The Lamb wave is generated on one side of the lap splice joint, propagates along the plate, interacts with the joint and is detected on the other side by a micromachined air-coupled capacitance transducer. Analysis of recorded signals allows to evaluate the condition of the bond.

• Composites Research
• /
• v.23 no.1
• /
• pp.37-43
• /
• 2010

In this paper, we present the result of an experimental investigation pertaining to the structural behavior of bolted lap-joint connection of pultruded fiber reinforced plastic structural shapes. In the experimental investigation, in order to find the mechanical property of the material, tension and shear tests on the pultruded structural composite specimen are conducted prior to the investigation on the structural behavior of bolted lap-joint connection of the member. Based on the result, number of bolts, type of placement and location of bolt are determined to be a test variable. Three different types of experimental specimens are prepared. Tensile load is applied through the center of the specimen with lap-joint connection and the structural behavior and failure mode of the test specimens with respect to the tensile load increment are investigated. As a result, it is found that most of the failure mode at the lap-joint connection is shear failure mode. Consequently, it is also found that the data obtained through this experimental program could be used for the structure connection design as a basis.

• The Journal of Engineering Geology
• /
• v.17 no.2 s.52
• /
• pp.271-277
• /
• 2007

To find out the anomalous zone in cut slope composed of phyllite and shist, we performed resistivity tomography using a pole-dipole way. The electrical distribution that propagates from a current source in lower part of slope is measured by a potential electrode in upper part of slope. Apparent resistivity data are inverted with an iterative regularized inversion method to reconstruct 3D resistivity image. By comparing with the resistivity images in relation to each section, the images of anomalous zone correspond to their positions represented in cut slope. Therefore, the application of resistivity tomography in cut slope is useful to recognize the extension of anomalous zone.

• Journal of Biomedical Engineering Research
• /
• v.23 no.5
• /
• pp.351-364
• /
• 2002

Conventional 3D ultrasound imaging using mechanical ID arrays suffers from poor elevation resolution due to the limited depth-of-focus (DOF). On the other hand, 3D imaging systems using 2D phased arrays have a large number of active channels and hence require a very expensive and bulky beamforming hardware. To overcome these limitations, a new real-time volumetric imaging method using curved 2-D arrays is presented, in which a small subaperture, consisting of 256 elements, moves across the array surface to scan a volume of interest. For this purpose, a 2-D curved array is designed which consists of 90$\times$46 elements with 1.5λ inter-element spacing and has the same view angles along both the lateral and elevation directions as those of a commercial mechanical 1-D array. In the proposed method, transmit and receive subapertures are constructed by cutting the four corners of a rectangular aperture to obtain a required image qualify with a small number of active channels. In addition the receive subaperture size is increased by using a sparse array scheme that uses every other elements in both directions. To suppress the grating lobes elevated due to the increase in clement spacing, fold-over array scheme is adopted in transmit, which doubles the effective size of a transmit aperture in each direction. Computer simulation results show that the proposed method can provide almost the same and greatly improved resolutions in the lateral and elevation directions, respectively compared with the conventional 3D imaging with a mechanical 1-D array.

• Biomedical Science Letters
• /
• v.2 no.1
• /
• pp.57-69
• /
• 1996

To examine the process of spermiogenesis in the Korean red-backed vole, Clethrionomys rufocanus regulus, the seminiferous epithelium in the testis, was studied by trasmission electron microscopy, and the following results were obtained based on the morphological characteristics of cell differentiation. 1. According to the fine structural differentiation, spermiogenesis was divided into Golgi, cap, acrosome, maturation and spermiation phases. Besides, these phases were sub-divided into two steps : early and late phases respectively, Thus, the spermiogenesis of Clethrionomys rufocanus regulus was divided into a total of ten steps. 2. In the changes of the chromatin, the chromatin granules began to be condenced in the late Golgi phase, regularizated at maturation phases, and a perfect nucleus of sperm was formed at the spermiation phases. 3. The sperm head had the falciform, and the formative period of sperm tail began to be develop in the early Golgi phase and completed at the spermiation phases. 4. In the morphological features of spermiation phases, the spermatid of early spermiation phase was divided into three types : (1) A-type spermatid contained cytoplasmic droplets in the neck region and middle piece, and the mitochondria was irregular, and arranged around the axoneme. (2) B-type contained cytoplasmic droplet in the middle piece only, and the mitochondria are arranged the center of axoneme regularly, and (3) In the C-type spermatid, the arrangement of mitochondria was regular, and was contained cytoplasmic droplet in the neck region only. In the late spermiation phase, only the sperm head was surrounded by cytoplasm of Sertoli cell or the matured sperm just before the spermiation from the cytoplasm of Sertoli cell.

• Korean Journal of Optics and Photonics
• /
• v.29 no.6
• /
• pp.275-284
• /
• 2018

In this study we propose a hybrid color-filter design method in which a nanohole array and a nanodisk array are separated by nanopillars of the material AZ 1500. We propose a design method for an RGB color filter, using the tendency of transmitted light according to each design variable. Especially we analyzed the intensity distribution of the electric field in the cross section, and set the height of the nanopillars so that the local surface-plasmon resonances generated in the two different arrays do not affect each other. The optical characteristics of the optimized color filter are as follows: In the case of the red filter, the ratio of the wavelength band expressing red in the visible broadband is 55.01%, and the maximum transmittance is 41.53%. In the case of the green filter, the ratio of the wavelength band expressing green is 40.20%, and the maximum transmittance is 42.41%. In the case of the blue filter, the ratio of the wavelength band expressing blue is 32.78%, and the maximum transmittance is 30.27%. We expect to improve the characteristics of color filters integrated in industrial devices by this study.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.54-54
• /
• 2011

기존의 착저식 방파제를 보완하기 위하여 부유식 방파제가 개발되었고, 많은 연구가 선행되어 왔다. 부유식 방파제의 최대 장점은 경제성과 친환경성이다. 그러나 부유식 방파제는 소파성능이 떨어진다는 단점이 있으며, 이를 개선하기 위해 잠재와 혼용, 배열형에 관한 연구등이 선행되어왔다. 그러나 이것은 경제성이라는 강점을 고려하지 못하였다. 그래서 본 연구에서는 부유식 방파제의 중요한 장점중 하나인 경제성을 고려해, 단면현상 변화만을 이용하여 부유식 방파제의 소파성능 개선하고자 하였다. RANS(Reynolds averaged Navier-Stokes) 방정식에 기초하여 VOF법과 $k-{\varepsilon}$ 난류모델을 결합한 수치모델인 CADMAS-SURF를 이용하였으며, 구조물 단면형상 변화를 이용해 와의 상호 간섭을 유도하였고, 이에 따른 투과율 변화를 관찰 하였다. 결과를 살펴보면 요철1 단면에서는 구조물 전면 하단부분과 구조물 후면 하단부분에서 와의 간섭이 일어났으며 가장 아래 요철 부분에서 유속의 전달현상이 보인다. 투과계수는 일반적인 부유식 방파제와 마찬가지로 L/B가 1~4사이 값인, 비교적 단주기에서는 0.3~0.4의 투과율을 보였으나 L/B가 5를 넘어가면서 0.45~0.55의 투과율을 보였고, 요철2 단면에서는 전면과 후면에서 발달한 와가 전, 후면 돌출부에 의해 바닥까지 전파되지 못하는 양상을 보였으며, 돌출부 사이 중앙부분에서 가장 활발한 와의 간섭을 관찰 할 수 있었다. 돌출부 아래에서 역시 강력한 와의 간섭을 보이고 있다. 투과율 역시 가장 낮은 값을 보였으며 비교적 단주기 구간인 B/L 1~4 에서는 0.2~0.35 사이의 값을 가졌으며 5~10사이구간에서는 0.35~0.34의 값을 보이고 있다. 이 같은 결과는 와의 간섭이 가장 활발하게 나타난 결과로 보인다. 그리고 요철 3단면에서는 전면 돌출부 끝단에서의 활발한 와의 간섭을 관찰 할 수 있었다. 투과율은 세 단면 중 가장 높은 값의 투과율을 보이지만 B/L 3~4 구간에서 요철1 경우보다 낮은 값의 투과율을 보이고 있다. 결과에서 보듯이 도출부의 적절한 조합과 배치를 통해 언급한 연구목표(와의 생성과 간섭, 방파효율 개선)를 달성하였고 추후에 돌출부의 크기와 배치, 흘수의 영향, 수심의 영향 등을 고려한 연구가 진행된다면 더욱 우수한 단면형상을 개발 할 것이라 예상된다.

• The Korean Journal of Zoology
• /
• v.32 no.2
• /
• pp.84-92
• /
• 1989

The dermatoglyphic paffems of the hands and feet form during early fetal life and thereafter remain essentially unchanged. These traits are useful to study genetics and environmental factors that influence prenatal life and used in practice for personal identification and diagnosis of some diseases. The students of 112 male and 118 female were tested for the paffems of plantar regions. The most common patterns were open fields in the four interdigital areas and the frequency of the mirror pattern on them was 57.2%. For a-b, b-c and c-d ridge counts of the plantar interdigital areas sampled from 105 male and 109 female students, the nonsignificances were found between both sexes and between both feet.