• Composites Research
• /
• v.24 no.5
• /
• pp.23-28
• /
• 2011

In this paper, the bonding strengths of co-cured T800 carbon/epoxy composite-aluminum single lap joints with and without additional pressures were investigated using the pressure information induced by the fiber tension during a filament winding process. The specimens of all the tests were fabricated by an autoclave vacuum bag de-gassing molding being controlled forming pressures (absolute pressures of 0.1MPa, 0.3MPa and 0.7MPa including vacuum). A special device which can act uniform additional pressures on the joining part of the single lap joint specimen was designed to measure the bonding strengths of composite-aluminum liners of type III hydrogen pressure vessel fabricated by a filament winding process. After the three different additional pressures (absolute pressures of 0.1MPa, 0.3MPa and 0.7MPa) were applied to the specimens the effect of the additional pressures on the bonding strengths of the co-cured single-lap joints were evaluated.

• Tuberculosis and Respiratory Diseases
• /
• v.44 no.3
• /
• pp.592-600
• /
• 1997

Background : The level of imposed work of breathing (WOB) is important for patient-ventilator synchrony and during weaning from mechanical ventilation. Triggering methods and the sensitivity of demand system are important determining factors of the imposed WOB. Flow triggering method is available on several modern ventilator and is believed to impose less work to a patient-triggered breath than pressure triggering method. We intended to compare the level of imposed WOB on two different methods of triggering and also at different levels of sensitivities on each triggering method (0.7 L/min vs 2.0 L/min on flow triggering ; $-1\;cmH_2O$ vs $-2cm\;H_2O$ on pressure triggering). Methods : The subjects were 12 patients ($64.8{\pm}4.2\;yrs$) on mechanical ventilation and were stable in respiratory pattern on CPAP $3\;cmH_2O$. Four different triggering sensitivities were applied at random order. For determination of imposed WOB, tracheal end pressure was measured through the monitoring lumen of Hi-Lo Jet tracheal tube (Mallincrodt, New York, USA) using pneumotachograph/pressure transducer (CP-100 pulmonary monitor, Bicore, Irvine, CA, USA). Other data of respiratory mechanics were also obtained by CP-100 pulmonary monitor. Results : The imposed WOB was decreased by 37.5% during 0.7 L/min on flow triggering compared to $-2\;cmH_2O$ on pressure triggering and also decreased by 14% during $-1\;cmH_2O$ compared to $-2\;cmH_2O$ on pressure triggering (p < 0.05 in each). The PTP(Pressure Time Product) was also decreased significantly during 0.7 L/min on flow triggering and $-1\;cmH_2O$ on pressure triggering compared to $-2\;cmH_2O$ on pressure triggering (p < 0.05 in each). The proportions of imposed WOB in total WOB were ranged from 37% to 85% and no significant changes among different methods and sensitivities. The physiologic WOB showed no significant changes among different triggering methods and sensitivities. Conclusion : To reduce the imposed WOB, flow triggering with sensitivity of 0.7 L/min would be better method than pressure triggering with sensitivity of $-2\;cm\;H_2O$.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.539-544
• /
• 2012

An experiment of rapid pressurization-induced crack propagation of solid propellant was conducted by using a windowed test chamber. A pre-cracked specimen of solid propellant is installed in the chamber, and highly compressed nitrogen gas in a accumulator pressurizes the chamber until the chamber pressure reaches set-up pressure to make the chamber depressurization. Pressure-time trace was obtained from the experimental result, and pressurization rate was defined from the trace. In this study, three pressurization rates (64.34, 73.86 and 85.44 MPa/s) are considered, and propagation lengths are measured. Also, a progression of the crack propagation recorded by a high-speed digital camera is presented.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.1
• /
• pp.195-202
• /
• 2004

The shell due to the effect of initial normal pressures on the shell surface was based on the assumption that the directions of the pressures are always normal to the undeformed shell surface, and that the change in the surface area of the shell is negligible. But the fact that the pressure are always normal to the deforming surface leads "follower force". The follower effect in the analysis can significantly alter the solution for natural frequency and buckling load as compared to the case when the direction of the pressures are assumed to be normal to the uniform shell surface. The expression for the part of strain energy contribution from normal pressure due to the effect of follower force was derived and added to the element stiffness matrix of axisymmetric shell. In the case of increasing external pressure, the natural frequencies decrease until one of them reaches zero. Theoretically the smallest applied load that reduces the frequency of any mode to zero, will have same magnitude as that of the buckling load. In order to determine the bucking load of the shell a few sets of frequencies are computed and the results considering the follower effects are well with the exact solution while the case without that are quite different. But in case of hemispherical dome, there are little difference in buckling pressure between with and without the effect of follower force.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.191-191
• /
• 2011

반도체 공정은 매우 복잡한 가스를 사용하기 때문에 여러가지 물질이 생성될 수 있다. 특히 플루오르계열 가스는 응축되어 부식성 물질로 변하여 펌프에 영향을 줄 수 있다. 이렇게 좋지 않은 조건을 만들지 않기 위해서 모든 가스들은 원래 상태로 이동하여 나오는 것이 가장 이상적이다. 그러나 챔버에서 반응하지않은 가스는 펌프로 오게 되면 온도와 압력이 달라져서 응축과 화학반응에 의해서 다른 부가물을 만들고, 이것들은 이러한 반도체 공정을 가능하게 하는 진공펌프에 영향을 주어서 고장을 일으킨다. 이러한 펌프에서 부가물을 채취하였다. 그리고 각 공정에서 생성되는 부가물을 분석하기 위하여 FT-IR, XRD, SEM(EDS), XRF분석법을 사용하였다. 이러한 분석법으로 부가물을 규명하고, 생성 원인을 규명하여 펌프의 성능 향상과 개선을 해보고자 한다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.2
• /
• pp.267-274
• /
• 2018

A variety of appendages are attached to coastal and offshore fishing boats to improve stability during navigation or fishing operations (stability performance and roll reduction). These appendages are generally classified into three types, which are shown in Fig. 1. The numerical calculations were conducted for the following eight cases: one case of a bare hull, three cases where a single appendage attached, three cases of a pair of appendages attached, and one case where all three appendages were attached. Table 1 presents the main dimensions of the bare hull and Table 2 describes the main dimensions of the three appendages. The fluid dynamic performance with regard to the three hull appendages was evaluated via CFD for the following cases: each of the appendages attached independently, a pair of appendages attached, and all three appendages attached simultaneously. The No. 1 appendage showed that pressure resistance was proportionally greater than friction resistances. Both Nos. 2 and 3 appendages showed comparable levels of pressure and friction resistances. The correlation between appendages was minimal in the case of pairs and Comparing the cases of the No. 2 appendage attached and all appendages attached, at 11 kn, the EHP showed an difference of 9 %.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.2
• /
• pp.91-96
• /
• 2010

To improve the limit of efficiency of squeezing oil in a conventional method, which seeds are compressed simply, the adoptability of the additional energy by the ultrasonic wave was investigated experimentally. As the results, using the ultrasonic vibration from the Langevin-type transducer, the efficiency was increased up to 25 %, whereas the conventional method has 15% efficiency. To investigate the additional pressure by the ultrasonic wave, the acoustic impedance of the sample and the vibration velocity of the transducer were measured. Although the amplitude of the ultrasonic is about 2.8 % of the compression pressure, the efficiency is increased a lot as mentioned above because the pressure is changed according to ultrasonic period.

• Journal of the Korean Society for Railway
• /
• v.14 no.5
• /
• pp.391-397
• /
• 2011

In this paper, the pressure endurance test of passenger train's glass window which was developed for next high speed train was studied. At first, pressure test equipment which will be able to generate the maximum pressure same as crossing case between two trainsets in the tunnel was developed. Afterwards the pressure test and evaluation that are based on NFF31-314 were carried out and studied.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.381-384
• /
• 2011

Wave drag reduction due to the repetitive laser induced energy deposition over a flat-nosed cylinder is experimentally conducted in this study. Irradiated laser pulses are focused by a convex lens installed in side of the in-draft wind tunnel of Mach 1.94. The maximum frequency of the energy deposition is limited up to 80. Time-averaged drag force is measured using a low friction piston which was backed by a load cell in a cavity as a controlled pressure. Stagnation pressure history, which is measured at the nose of the model, is synchronized with corresponding sequential schlieren images. With cylinder model, amount of drag reduction is linearly increased with input laser power. The power gain only depends upon the pulse energy. A drag reduction about 21% which corresponds to power gain of energy deposition of approximately 10 was obtained.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.1087-1090
• /
• 1999

중수로(CANDU) 형 월성 원자력발전소의 칼란드리아 압력관 전면부를 감시점검하기 위한 열영상 관측프로그램을 개발하였다. 국내의 사용자들의 요구에 부응할 수 있는 다양한 기능을 부가 하였다. 부가된 기능에는 임의의 포인트, 영역, 라인, 경계선을 마우스로 지정하여, 선택된 지점, 영역, 라인 및 경계선의 특징을 추출할 수 있는 기능을 갖추고 있다. 또한 KAERI Thermo Inspector 의 기능을 살린 일반영상/열영상의 매핑기능을 부가하였다. 일반영상에 비해 상대적으로 해상도가 떨어지는 열영상대신에 CCD 영상의 관측포인트를 지정하면 열영상카메라좌표계의 매핑된 지점의 이상상태를 판정할 수 있는 특성을 갖는다.