• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.1
• /
• pp.1-5
• /
• 2018

The present study investigated the characteristics of vertical sagging down of high temperature in chamber and characteristics of vertical sagging down in the outdoor asphalt sheet and asphalt seal under korea ltimate condition using asphalt seal products of solvent based type, solventless type, water dispersion type, and heat melting type, which are currently applied in Korea. Prior to the investigation of outdoor vertical sagging down characteristics, the assessment of sagging down performance of single use of sealing products at $20^{\circ}C$, $40^{\circ}C$, $60^{\circ}C$ was conducted and the result showed that sagging down did not occur at $20^{\circ}C$ but some solventless type, water dispersion type specimens at $40^{\circ}C$ had sagging down up to 10 mm. In addition, some solventless type, water dispersion type specimens had sagging down up to 55 mm at $60^{\circ}C$. For specimens to which asphalt seal and renovated asphalt sheet were layered over the outdoor concrete vertical surface, sheet sagging and sagging down occurred up to 50 mm in water dispersion specimens after three month later since the construction in summer.

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2016.11a
• /
• pp.198-199
• /
• 2016

기존 콘크리트 구조물의 내력 및 처짐에 저항하기 위하여 섬유시트를 사용한 복합섬유 패널 보강재를 셋 앵커를 이용하여 콘크리트 구조물과 일체화시키는 공법을 개발하였다.. 본 연구에서 적용된 실험 결과에 의하면 엥커+에폭시 보강 I 시험체가 기준시험체에 비하여 최대하중이 3.13배 증가, 동일 앵커갯수인 앵커보강시험체에 비하여 1.14배 증가하여으며, 에폭시보강시험체는 기준시험체에 비하여 최대하중이 3.08배 증가하였으나 계면에서 섬유박리로 인한 취성 파괴가 발생하였다.

• Membrane Journal
• /
• v.25 no.6
• /
• pp.530-537
• /
• 2015

Photovoltaic (PV) modules are environmentally energy conversion devices to generate electricity via photovoltaic effect of semiconductors from solar energy. One of key elements in PV modules is "Backsheet," a multilayered barrier film, which determines their lifetime and energy conversion efficiency. The representative Backsheet is composed of chemically resistant poly(vinyl fluoride) (PVF) and cheap poly(ethylene terephthalate) (PET) films used as core and skin materials, respectively. PVF film is too expensive to satisfy the market requirements to Backsheet materials with production cost as low as possible. The promising alternatives to PVF-based Backsheet are hydrocarbon Backsheets employing semi-crystalline PET films instead of PVF film. It is, however, necessary to provide improved barrier property to water vapor to the PET films, since PET films are suffering from hydrolytic decomposition. In this study, a polyurethane adhesive with reduced water vapor permeation behavior is developed via a homogeneous distribution of hydrophobic silica nanoparticles. The modified adhesive is expected to retard the hydrolysis of PET films located in the core and inner skin. To clarify the efficacy of the proposed concept, the mechanical properties and electrochemical PV performances of the Backsheet are compared with those of a Backsheet employing the polyurethane adhesive without the silica nanoparticles, after the exposure under standard temperature and humidity conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.107-107
• /
• 2010

IT 산업의 발달과 더불어 카메라, 휴대폰, 노트북, 캠코더 등 전기전자 응용분야에 복합기능성 실리콘 고무 시트가 사용되고 있다. 본 연구에서는 실리콘 고무의 사용시 발생하는 정전기를 방지하기 위해 습도와 온도 변화에 따른 정전기 대전전압을 측정하였다. 카본양의 증가에 따라서 대전전압이 감소하였으며 습도가 증가됨에 따라 정전기 대전량은 감소하였다. 12Phr카본 첨가시 대전과 동시에 완화가 일어남을 확인했다.

• Journal of the Korea Institute of Building Construction
• /
• v.3 no.2
• /
• pp.119-127
• /
• 2003

Test specimen test was performed using concrete reinforced with fiber sheet and the test variables were based on the kinds of fiber and the number of reinforcement layers. Using steel-concrete reinforced with fiber sheet, compression tests were performed and the test variables were the kinds of fiber, number reinforcement layers and reinforcement layer order. The following results were obtained: 1) It was demonstrated that compressive strength of the test specimen reinforced during test specimen test and member test increased as the number of reinforcement layers increased. 2) It was shown that non-reinforced test, specimen were destroyed during the member tests, but the specimen reinforced with CFS destroyed and the GFS-reinforced specimen and composite reinforced specimen showed ductile destruction. 3) As a result of tests on kinds of reinforcement fiber, it was demonstrated that CFS-reinforced test specimen had higher compressive strength in a 공시체 test. In the member test, 2ply-and 3ply-GFS reinforced specimens except lplied one had higher compressive strength. It was because partial destruction occurred due to the rate of height/section. 4) For layer strength order, compared with test specimen reinforced only with a single reinforced material, test specimen reinforced with CFS and GFS, and test specimen reinforced with CFS first showed better results in compressive strength and ductility judgement.

• The Journal of the Korea Contents Association
• /
• v.20 no.12
• /
• pp.529-536
• /
• 2020

This paper presents experimental investigations about compressive strength and durability of reinforced concrete compressive members repaired using ductile fiber reinforced cementitious composite (DFRCC) and carbon fiber sheet through freezing and thawing test. Total 24 RC specimens of 100x100x400mm size were tested by compressive strength test and freezing and thawing test by KS F 2456. The specimens were reinforced using 4D10 steels and repaired on 4 sides expect on top cycle. Test results showed that the specimens repaired using fiber carbon sheet revealed about 5% higher values of the compressive strength compared than the cases of DFRCC motar. On the other hand, the resurts did not showed meaningful differences in the aspect of durability. For further research, considerations of the steel interference effect and real old specimens such as taken from real deteriorated structures are needed to be tested after repairing with DFRCC and carbon fiber sheet.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.19-19
• /
• 2012

최근 산업환경 변화에 순응하는 환경 친화적 소재를 사용하여 자동차, 선박, 철도 등 수송용 인테리어 내장재를 구성하는 기술로서, 난연성 및 기계적 물성 유지 기술, 그리고 실내 쾌적감을 부여하기 위한 감성기술 및 심미적 요소를 부여하는 디자인 기술이 가미된 복합 기능화 기술개발이 구되고 있다. 기존의 자동차용 시트 제품은 대부분 PU Foam을 시트원단에 불꽃으로 Lamination 하는 방식으로 제조되었으며, 이러한 제조 방식은 많은 공정을 거치게 되고 PU Foam을 제조하는 공정 및 불꽃으로 Lamination 하는 공정에서 많은 환경유해가스가 발생하는 등 환경적으로도 많은 문제점을 감수하면서 생산하는 방식이다. 또한 각종 원단의 표피재로 많이 사용되고 있는 PU와 PVC의 경우 제조과정에서 용제와 가소제 사용 등으로 인해 환경적으로 많은 문제점이 있으며, 이를 대체하기 위한 노력이 많은 부분에서 이루어지고 있지만, 마땅히 대체할 소재를 찾지 못하고 있는 실정이다. 본 연구에서 제안하는 실리콘수지는 기존의 PU와 PVC를 대체할 수 있는 소재로서 각광받고 있으며, 응용기술 개발을 통해 충분히 적용이 가능한 소재라고 판단된다. 본 연구에서 개발하고자 하는 기술은 난연성을 가진 실리콘 내장 표피재에 불꽃으로 Lamination하는 공정을 배제한 친환경 PUD Foam을 바로 Back Coating함으로써 일체형 고 기능 친환경 제품을 개발함으로써 친환경 복합화 기술 및 SEAT 원단과 표피재의 일체형 모듈화 공법개발을 이루고자 한다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.613-616
• /
• 2008

This study is about appling non-exposure waterproofing method which combines the Cement Polymer Modified Waterproof Membrane coating and Selfadhesive Rubberized Asphalt sheet to the Roof Structure, Because there are a lot of problems in previous methods. So We had the performance tests using waterproofing method which combines two materials, and we analyzed the results. This study showed us very important results. We had bond strength test and tensile test under high, normal and low temperature, and the results were successful. And we also tested for coping with crack and movement. We found that tested materials were safe in those conditions. I think that Non-Exposure waterproofing method which combines the Cement Polymer Modified Waterproof Membrane coating and Selfadhesive Rubberized Asphalt sheet is available to concrete structure.

• Composites Research
• /
• v.35 no.6
• /
• pp.469-476
• /
• 2022

In this paper, the microwave absorbing characteristics after the impact of the radar-absorbing structure (RAS) consisting of periodic pattern sheet (PPS) and glass fiber-reinforced plastic (GFRP) were experimentally investigated. The fabricated RAS effectively absorbed the microwave in the X-band (8.2-12.4 GHz). In order to induce the damage to the RAS, a low-velocity impact test with various impact energy of 15, 40, and 60 J was conducted. Afterward, the impact damage was observed by using visual inspection, non-destructive test, and image processing method. Moreover, the absorbing performance of intact and damaged RAS was measured by the free-space measurement system. The experiment results revealed that the delamination damage from the impact energy of 15 J did not considerably affect the microwave absorbing performance of the RAS. However, fiber breakage and penetration damage with a relatively large damaged area were occuured when the impact energy was increased up to 40 J and 60 J, and these failures significantly degraded the microwave absorbing characteristics of the RAS.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.352-353
• /
• 2003

Clay 분산 유/무기 나노복합재 제조기술은 실리케이트 층상구조의 점토광물을 나노 스케일의 시트상의 기본 단위로 박리(exfoliation)하여 고분자수지에 분산시킴으로써 범용 고분자의 낮은 기계적 물성의 한계를 엔지니어링 플라스틱 수준으로까지 올리고자 하는 것으로서, 기존의 무기 충진재 및 강화재의 입자크기(〉1 $\mu\textrm{m}$)를 나노 스케일까지 분산시켜 기존 무기물 충진 복합재의 단점을 한층 보완하는 것을 목표로 하고 있어 성능 및 원가 면에서 매우 유리한 방법으로 21세기의 복합재료 생산시장의 판도에 상당한 변화를 가져오게 할 수 있는 핵심기술이라 할 수 있다. (중략)