• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.12
• /
• pp.821-827
• /
• 2014

The 4major river project has caused changes in flow and water quality patterns in major rivers in Korea including the Nakdong River where several toxicant release accidents have had occurred. Three dimensional hydrodynamic model, the Environmental Fluid Dynamics Code (EFDC), was applied to evaluate the effect of geomorphological change of the river on the advection and dispersion patterns of a conservative toxic pollutant. A hypothetical scenario was developed using historical data by assuming a toxic release from an upstream location. If there is a toxic release at the Gumi Industrial Complex, the toxic material would be detected after 2.22 and 9.83 days at Chilgok and Gangjung weir, respectively, in the new river system. It was estimated that they took at least 12 times longer than those with the river conditions before the project. Effect of relocation of intake towers for Daegu Metro City to upstream of Gumi City was also evaluated using the developed modeling system. It was observed that hydraulic residence time would be increased due to decreased flow rate and thus due to lowered water level. However, peak concentration differences were found to be about 2% lower in both places due to increased dispersion effect after the relocation.

• Journal of Korea Water Resources Association
• /
• v.41 no.8
• /
• pp.761-772
• /
• 2008

The object of this study is to develop the model that solves the numerically difficult problems in hydraulic engineering and to demonstrate the applicability of this model by means of various test examples, such as, verification in the gradually varied unsteady condition, three steady flow problems with the change of bottom slope with exact solution, and frictional bed with analytical solution. The governing equation of this model is the integral form of the Saint-Venant equation satisfying the conservation laws, and finite volume method with the Riemann solver is used. The evaluation of the mass and momentum flux with the HLL Riemann approximate solver is executed. MUSCL-Hancock scheme is used to achieve the second order accuracy in space and time. This study introduce the new and simple technique to discretize the source terms of gravity and hydrostatic pressure force due to longitudinal width variation for the balance of quantity between nonlinear flux and source terms. The results show that the developed model's implementation is accurate, robust and highly stable in various flow conditions with source terms, and this model is reliable for one-dimensional applications in hydraulic engineering.

• Journal of Conservation Science
• /
• v.29 no.4
• /
• pp.379-388
• /
• 2013

Damaged the Jeoguibon (patterns of the Queen's ceremonial robe) was found during repair work of Daejojeon, Changdeok Palace in 2011. Analytical study on seven colors painted in the patterns has been conducted by P-XRF and Micro-XRD analysis. The result displays that red lead, ultramarine blue, conichalcite or mixed pigment of emerald green and barium white, orpiment and white lead had been used on the patterns. Comparison of the pigments used for the Pyeseulbon (patterns of the Queen's belt ornament covering knees in the front) housed in National Museum of Korea has revealed that not only red lead but also cinnabar and organic pigment had been used in the Jeoguibon and the Pyeseulbon housed in National Museum of Korea. In addition the same pigments has been examined in green and yellow parts of both the Jeoguibon in Daejojeon and the Pyeseulbon housed in National Museum of Korea. The result has shown that western's synthetic green pigment such as emerald green was introduced and used in 1920's. The scientific result from this study expects to be used as useful referencing data for the comparative understanding on pigments used in palace during the 20th century.

• Journal of Conservation Science
• /
• v.26 no.4
• /
• pp.371-376
• /
• 2010

The great jar estimated in Proto-Three Kingdoms period was found at the site from Pyeongtaek Daechuri and the bonding traces from pieces destroyed when they were excavated are observed. Therefore this study would figure out the components of bonding material used in great jars by optical microscope, FT-IR, py-GC/MS and the kind of textile attaching to great jar by transmitted light microscope. As a result of optical microscope for the cross-section, black material is uniformly applied between a piece of jar and the part of bonding and the textile line are observed. Black bonding material is resulted in korean rhus lacquer by FT-IR and py-GC/MS and the kind of textile is identified as hemp by transmitted light microscope. Materials for repairing archaeological objects are hardly known causing little information, but this study proves that the bonding material had used lacquer for great jars before Proto-Three Kingdoms period. Therefore if ancient bonding materials are systematically analysed in the further studies, it would be significant help for studying bonding and restoration materials of ancient objects.

• Journal of Conservation Science
• /
• v.35 no.3
• /
• pp.217-225
• /
• 2019

The chimi(ridge-end tile) of Wangheungsa temple is the oldest in our country. The upper part of the chimi was excavated from the southern side of Wangheungsa temple and the lower part from the northern side. These parts are considered to be portions of the same chimi, because they are similar in shape and are excavated from two sides of the same temple structure. However, the original shape of the chimi cannot be determined owing to substantial deterioration. Hence, in this study, replicas of the deteriorated chimi portions of Wangheungsa temple were fabricated by employing 3D scanning technology and the computer numerical control machining method. While observing the bending phenomenon of the chimi, the proposed model was warped realistically on the basis of the bending direction of the actual chimi. Consequently, the restoration process was modified several times. The results indicated that no gaps can be found between the upper and lower parts, and the corresponding patterns connect naturally. Furthermore, the proposed method is contactless, safe, operable, reproducible, and appropriate for restoration of artifacts. Additionally, the modeling data is semi-permanent. Hence, if modelling data is appropriately applied as per the characteristics of artifacts, it can be utilized in various fields such as virtual exhibitions, hands-on exhibitions, cultural heritage restoration, and production of teaching aids and souvenirs.

• Korean Journal of Heritage: History & Science
• /
• v.50 no.4
• /
• pp.148-165
• /
• 2017

Mural paintings drawn inside ancient tombs are very sensitive to changes in the environment such as temperature and humidity, especially the finish layer of the tomb murals differ in preservability depending on the material properties and humidity conditions. In this study, I examined the mural painting of Songsan-ri Tomb No.6, where the finish layer was made of earth, and identified the physical changes that can occur due to drying, depending on the material properties of the finish layer. I found out through particle size analysis that the finish layer of the mural painting in Songsan-ri Tomb No.6 is about 85.0wt% below silt, about 14.0wt% clay therein, mostly composed of silt and below clay. I also found out through physical property evaluation that surface change rate of samples showed the largest change at 15.5% in reproduced finish layer sample made up of bentonite, followed by 7.8% of reproduced finish layer sample made up of celadon soil, 6.3% of reproduced finish layer sample made up of loess, 6.2% of reproduced finish layer sample composed of white clay and the same order of change in appearance was confirmed in each sample consisted of soil. In addition, it showed the same trend of surface change rate, and the bentonite condition showed the largest change, in the measurement of shrinkage rate and expansion rate. The experiment shows that the finish layer composed of soil is affected by cohesion among particles according to the content of fine parts and the relationship between the agglomeration due to the content of the differentiated part and the stress due to the expansibility depending on the kind of the clay mineral etc. Therefore, it can be concluded that the physical damage occurred in the mural painting finish layer of the Songsan-ri Tomb No.6 is related to the factors such as the material characteristics of the soil and the highly humid environmental change inside the tomb.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.5
• /
• pp.418-428
• /
• 2007

In the calculation of wave propagation by Boussinesq equation model, it is very common to experience numerical noises generated from nonlinear interaction and breaking wave occurrence, and the numerical solution is rapidly diverged unless the noises are properly controlled. A comparative study was here undertaken for the characteristics of three different lowpass filters (FFT filter, Gaussian filter and Shapiro filter) which are all designed to be applied to the interim results of numerical calculation. The numerical results obtained with application of respective filter techniques were compared with the results of an existing hydraulic experiment for the aspects of noise suppression, conservation of main signal and altering time. The results show that the Shapiro filter can be best applied with optimal choices of its element number, pass number and filtering tune interval. The combination of the number of filter element off, pass number of 50 or less, and application interval of 100 to 200 time steps generally showed good performance in both accuracy and efficiency of the numerical calculation.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1219-1223
• /
• 2007

수온은 수계에서 가장 중요한 물리적 특성 중 하나로서, 생물 군집, 특히 어류와 무척추 동물에 관련된 많은 수질 인자에 영향을 미친다. 하천의 생태학적 모습을 개선하기 위한 하천 복원 사업 수행에 있어서, 서식처 및 산란처 조건으로서의 수온 조사 및 모델링의 필요성이 점차 증가하고 있는 상황이다. 본 연구는 낙동강의 중상류에 위치한 반변천 합류부에 평면 이차원 비정상 수치모형인 KU-RLMS 모형을 적용하여 수온의 변화 특성을 규명할 목적으로 수행하였다. KU-RLMS 모형은 하천 및 저수지의 국부적인 수리, 수질, 유사이동 해석을 위해 개발된 평면 이차원 비정상 수치모형이다. 직사각형 격자를 사용하는 유한차분법의 단점을 보완하기 위해, 수심적분된 2차원 연속방정식, 운동량방정식, 이송확산방정식을 불규칙한 경계를 현실적으로 모사할 수 있는 직교곡선 좌표계로 변환한 방정식을 사용한다. 이 모형은 흐름, 농도, 지형변화를 조합하여 계산할 수 있는 모형으로서 점착성 및 비점착성 유사의 이동, 보존성 및 비보존성 오염물질의 이동, 수온 변화를 모의할 수 있다. 수치모형 적용을 위한 현황분석으로 안동 및 임하 조정지댐의 방류량, 안동 수위관측소의 수위, 법흥교 및 포진교 지점의 수온 자료를 분석하였다. 이송확산모형의 보정을 위해, 안동대교 지점의 수온 횡분포 측정자료를 사용하여 확산계수에 대한 매개변수 추정 및 검증을 수행하였다. 또한, 안동조정지댐과 임하조정지댐의 방류량 및 방류수온을 고려하여 수치모의조건을 결정하였으며, 각 조건에 대한 수온 변화 특성을 분석하였다.

• Korean Journal of Ecology and Environment
• /
• v.50 no.1
• /
• pp.70-78
• /
• 2017

The Hwasan wetland vegetation is observed at mountain basin (644~780 m a.s.l.) where had become a potential land for indigenous people since prehistoric period. We phytosociologically investigated old-growth alder (Alnus japonica) forests using the $Z\ddot{u}rich$-Montpellier School's method and analyzed their spatial distribution pattern by actual vegetation map. Species performance was determined by using coverage and r-NCD. Viburnum opulus var. calvescens-Alnus japonica community syntaxonomically belonging to the Alnetea japonicae was first described and composed of three subunits: Salix koreensis subcommunity, typical subcommunity, and Pyrus ussuriensis subcommunity. Present plant community was compared with vicariant syntaxa such as Molinia japonica-Alnus japonica community, Rhamno nipponicae-Alnetum japonicae, and Aceri-Salicetum koreensis. Hwasan's alder forest, an alluvial terrace vegetation type on valley fan in the montane zone, is evaluated as vegetation class [I], which is a sort of benchmark plant community potentially on mountain wetlands in southeastern part of the Korean Peninsula. Simultaneously we suggested an establishment of the national strategy for habitat conservation free from hydrologically radical transform due to military utilization.

• Restorative Dentistry and Endodontics
• /
• v.20 no.2
• /
• pp.487-507
• /
• 1995

Composite resin repair requires strong bond strength between the new and old materials. The objective of the current study was to identify the optimal treatments for sufficient bond strengths. Bondings between same kinds of materials and cross bondings using chemical curing composites and light curing composites were tested. Surface treatments included the methods of sand-blasting, acid etching and coating of bonding agent. Seven kinds cases of combinations from three kinds of methods were experimented and compared with a control group of which surfaces were highly polished. Measurements of shear bond strength and observations of surface morphologic changes using a scanning electron microscope were done. Following conclusions were drawn : 1. The highest bond strength among composite resins were exhibited by the treatment of the sand-blasting and the coating of bonding agent. 2. Acid etched surfaces showed the lowest bond strength. Bond strengths obtained from experimental groups including acid etching were lower than those obtained from same kinds of experimental groups without acid etching. 3. Simple method of the coating of bonding agent produced the slightly increased bond strength on chemical curing composite and reduced bond strength on light curing composite. 4. Bonding surfaces of chemical curing composite resin showed slightly higher bond strengths than light curing composite resin, however significant differences were not confirmed statistically. 5. More significant irregular surfaces were created by sand-blasting method than acid etching method. 6. A principal component of fillers of both resins was silicon. Acid etching method produced the seperations and degradations of fillers, these were significant on light curing composite resins which containing barium fillers.